{"title":"Sebo Dart","description":null,"products":[{"product_id":"axle-for-swivel-neck-supports-for-et-1-and-et-2","title":"SEBO Swivel Neck Support Axle for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eEvery change of direction is absorbed by the neck joint between wand and power head. Part 2928 is the axle the swivel neck supports turn on, drawn at position 126 on SEBO's ET-1\/ET-2, DART and FELIX parts sheets, sitting one number along from the neck switch wiring that runs through the same joint.\u003c\/p\u003e\u003cp\u003eWear here is felt rather than seen. The head starts to lag behind the handle, flops at the end of a stroke, or refuses to follow into a turn at all. The right and left supports the shaft passes through are listed separately as 2311 and 2312 at positions 123 and 124, and they wear in step with it, so put a thumb on both and check for play while the joint is open. If the swivel also feels notchy rather than merely loose, the six-piece metal segment set 2950ER and the swivel neck bearing 2954 are the next two items on the same sheet worth inspecting. Disconnect the machine from the outlet before disturbing anything that carries power down into the head.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2928, supplied singly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e pivot shaft carrying the swivel neck supports\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 126 on the ET-1\/ET-2, DART and FELIX lists\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2311 support right, 2312 support left, 2954 swivel neck bearing, 2950ER metal segment set, 2307GS complete swivel neck\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTypical symptom:\u003c\/strong\u003e a head that wanders, flops or fights the line you are steering\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA SEBO ET-1 axle replacement is a bench job rather than a roadside one, but it is the quickest way to bring the steering back to where it was, and always worth doing while the neck is apart for any other reason. Genuine SEBO stock from an authorized dealer; ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214472339706,"sku":"2928","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2928.jpg?v=1709347663"},{"product_id":"bearing-block-l-h-complete-for-et-1-and-et-2-gray-black","title":"SEBO Left-Hand Bearing Block for ET-1 and ET-2 Power Heads — Gray Black","description":"\u003cp\u003ePosition 102 on SEBO's exploded views marks the left-hand brush roll bearing, and 2314GS is that component in gray black, assembled and ready to seat. The same position number applies across the ET 1 \/ ET 2 power head, DART and FELIX diagrams, so whichever sheet you are working from the reference holds.\u003c\/p\u003e\u003cp\u003eLeft and right blocks are not interchangeable and carry separate part numbers, so identify which end has gone noisy before ordering. Grinding under load, a roll that will not turn freely by hand, or visible play when you rock the roll in its seat all point at the bearing rather than the belt. The distinction matters because a slipping belt and a failed bearing can both leave a head that cleans poorly on carpet, yet the fix and the part are entirely different. With the roll out, spin each bearing on its own: a healthy one runs on smoothly for a few seconds, a failed one feels notchy or stops immediately, and a housing that has worn oval will let the whole bearing turn in its seat.\u003c\/p\u003e\u003cp\u003eBecause both ends accumulate identical hours, pairing this with the right-hand block, part 2313GS, avoids taking the head apart twice. Clear wound hair and thread from the roll shaft before reassembly, since that binding is what loads the bearings in the first place, and check the belt runs central on its pulley once everything is back together. Light gray ET-1 heads use the colour-matched block 2314HG instead of this one.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 as well as ET-2 power heads, switched or unswitched\u003c\/li\u003e\n\u003cli\u003ePart number: 2314GS\u003c\/li\u003e\n\u003cli\u003eLeft-hand brush roll bearing block, supplied complete with the bearing seated\u003c\/li\u003e\n\u003cli\u003eFinish: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 102 in the ET 1 \/ ET 2, DART and FELIX parts lists\u003c\/li\u003e\n\u003cli\u003eRelated numbers: 2313GS right-hand block, 2314HG in light gray\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO part. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214472962298,"sku":"2314GS","price":30.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2314GS.jpg?v=1785150350"},{"product_id":"bearing-block-r-h-complete-for-et-1-and-et-2-gray-black","title":"SEBO Right-Hand Bearing Block for ET-1 and ET-2 Power Heads — Gray Black","description":"\u003cp\u003eA brush roll that squeals at one end, wanders sideways, or takes a moment to come up to speed has usually lost a bearing. Part 2313GS is the right-hand half of that pair in the gray black finish, and it ships complete, so the bearing already sits in its housing and the repair is a swap rather than a press-fit rebuild on the bench.\u003c\/p\u003e\u003cp\u003eSEBO draws this piece at position 105 in the ET 1 \/ ET 2 power head diagram, and at position 105 again in the DART and FELIX diagrams. The failure has a recognisable arc. First comes a rise in running noise that tracks brush speed rather than motor speed, then the belt begins creeping toward one end of its pulley, and finally the roll develops enough play to be rocked visibly in its seat by hand. Left long enough, an out-of-square roll wears its own end cap and starts scrubbing the carpet harder on one side of the opening than the other.\u003c\/p\u003e\u003cp\u003eLook over the opposite end while the roll is out. The left-hand block, part 2314GS in the same finish, carries identical hours and tends to wear on much the same schedule, and doing both at once avoids a second strip-down. Clear wound hair from the roll shaft before reassembly, since that binding loads the bearings every time the head runs. Light gray ET-1 heads take block 2313HG instead, so order by the finish on the head in front of you. Fitment on this gray black block runs across both head widths, which is why one number covers uprights and canisters alike.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 as well as ET-2 power heads, switched or unswitched\u003c\/li\u003e\n\u003cli\u003ePart number: 2313GS\u003c\/li\u003e\n\u003cli\u003eRight-hand brush roll bearing block, supplied complete with the bearing seated\u003c\/li\u003e\n\u003cli\u003eFinish: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 105 in the ET 1 \/ ET 2, DART and FELIX parts lists\u003c\/li\u003e\n\u003cli\u003eRelated numbers: 2314GS left-hand block, 2313HG in light gray\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO part. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214473552122,"sku":"2313GS","price":18.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2313GS_74be7a83-888a-4bc1-812f-9e2c64caf642.jpg?v=1785153960"},{"product_id":"belt-333-3m-htdii-6-for-et-1-et-2-softcase-and-370-comfort","title":"SEBO Toothed Brush Belt 333 3M HTDII-6 for FELIX, DART, ET-1\/ET-2 and 370 COMFORT","description":"\u003cp\u003eA toothed belt cannot slip the way a smooth one does, which is why SEBO drives its brush rolls through a geared profile rather than a flat rubber loop. Part 2923 is the 333 3M HTDII-6, the same belt the SOFTCASE CE12 parts list records under the heading toothed belt 333 HTD 3M 6. It sits at position 103 on the ET-1\/ET-2, DART and FELIX sheets and at position 125 on the SOFTCASE CE12.\u003c\/p\u003e\u003cp\u003eThis is the one true consumable in the drive train. Everything else in the head is metal or moulded plastic; the belt is rubber, it is under constant tension, and it wears whether the machine is used hard or gently. A stretched belt announces itself as a brush that free-wheels, ticks under load, or gives up altogether in deep pile while the suction motor sounds entirely normal. One that has begun shedding teeth leaves black crumbs of its own inside the head, and a belt that has been run slack long enough will glaze and start to smell hot. Because the geared profile has to mesh, a tired belt also chews the pulley it runs on, so replacing it early is the cheaper decision.\u003c\/p\u003e\u003cp\u003eFull fitment is broad: the SEBO ET-1 and ET-2 power heads in both with-switch and without-switch versions, the FELIX Premium and FELIX 2 Premium, the DART, the 370 COMFORT, the CE12 SOFTCASE, the AIRBELT D4 PREMIUM, the AIRBELT E3 Premium, the AIRBELT K3 PREMIUM and the C3.1. On the 370 COMFORT it pairs with brush pulley 2919ER, and motor pulley 2319 is the driven end on the FELIX Premium, FELIX 2 Premium, DART, 370 COMFORT, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM, C3.1 and both ET heads. Access door 2909VO is the orange flap that has to come off to reach it. Keep a spare on the shelf; this is the part that strands a machine mid-room.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSEBO part 2923 — belt 333 3M HTDII-6, toothed\u003c\/li\u003e\n\u003cli\u003eFits: SEBO ET-1 and ET-2 power heads (with or without switch), FELIX Premium, FELIX 2 Premium, DART, 370 COMFORT, CE12 SOFTCASE, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1\u003c\/li\u003e\n\u003cli\u003eParts-diagram positions: 103 (ET-1\/ET-2, DART, FELIX), 125 (SOFTCASE CE12)\u003c\/li\u003e\n\u003cli\u003eType: geared drive belt, so it meshes rather than gripping by friction\u003c\/li\u003e\n\u003cli\u003eTypical symptom: brush free-wheeling, ticking under load, or stalling in deep pile\u003c\/li\u003e\n\u003cli\u003eRelated part numbers: 2919ER brush pulley, 2319 motor pulley, 2909VO access door\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine SEBO\u003c\/strong\u003e; ships in 2–5 business days\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214474535162,"sku":"2923","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0f2340c355f940c6ecec795e4f1492c2.jpg?v=1786668775"},{"product_id":"rear-bottom-plate-for-et-1-gray-black","title":"SEBO Rear Bottom Plate for ET-1 Power Heads — Gray Black","description":"\u003cp\u003eDebris left behind on the pull stroke usually points at the panel behind the roll rather than at suction. Part 2304GS is the gray black rear bottom plate used on ET-1 floor nozzles, closing off the rear of the underside and setting the height at which the trailing lip meets the floor.\u003c\/p\u003e\u003cp\u003eSEBO catalogues it at position 109 in three separate diagrams, the ET 1 \/ ET 2 power head list, the DART list and the FELIX list, each time as the complete rear bottom plate. Scraping, cracking and warping all open a gap along that edge, and a gap there bleeds air away from the roll where the airflow is meant to be doing its work. The symptoms read as a general loss of pickup on carpet, a thin line of grit left behind the head, or a nozzle that feels light and skittish instead of settling onto the floor. Hard flooring and threshold strips do most of the damage, since the plate takes the load every time the head is dragged backwards over a raised edge.\u003c\/p\u003e\u003cp\u003eTurn the head over and sight along the rear lip before ordering. A plate worn thin, missing a corner or bowed away from the shell is doing none of its job, and no amount of bag or filter changing will bring the pickup back while it stays there. The same panel covers a wide spread of machines, since the SEBO FELIX Premium, DART and C3.1 uprights and the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium canisters all run ET-1 heads. This is the gray black version; light gray heads take part 2304HG instead.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2304GS\u003c\/li\u003e\n\u003cli\u003eColour: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 109 in the ET 1 \/ ET 2, DART and FELIX parts lists\u003c\/li\u003e\n\u003cli\u003eSupplied complete\u003c\/li\u003e\n\u003cli\u003eRelated number: 2304HG in light gray\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eShips in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214476042490,"sku":"2304GS","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2304GS.jpg?v=1708929320"},{"product_id":"bumper-for-et-1-gray-black","title":"SEBO ET-1 Power Head Bumper — Gray Black","description":"\u003cp\u003eBaseboards, chair legs and door frames all take their turn against the front of a floor nozzle, and gray black bumper 2302GS is the trim that absorbs the punishment on ET-1 heads. It wraps the leading edge so the housing behind it never makes the contact, and it is the reason a well-kept head still looks straight after years of edge work.\u003c\/p\u003e\u003cp\u003eSEBO lists this moulding at position 101 in the DART parts diagram as the complete bumper. Trim hardens with age rather than with mileage, and the failure is predictable: it splits at a corner, works loose from its retaining channel, then lifts far enough to snag on the very furniture it exists to protect. Once that happens the marks start appearing on skirting boards and on the shell underneath. A strip that has gone rigid enough to rattle in its groove is worth changing before it takes a chip out of the housing. Replacement is a front-edge job with the head laid on its back; clear the channel of grit before pressing the new moulding home, and work from one corner across rather than pushing the middle down first.\u003c\/p\u003e\u003cp\u003eFitment runs wide on this one. The same trim serves the SEBO FELIX Premium, the DART, the C3.1 and the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium canisters, all of which use an ET-1 head, and it suits those heads whether or not they carry an on\/off rocker. Colour is the ordering decision: this is the gray black item, the light gray equivalent is part 2302HG, and the version bundled with the soft carpet front bottom plate is 2302SC.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2302GS\u003c\/li\u003e\n\u003cli\u003eColour: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 101, DART parts list\u003c\/li\u003e\n\u003cli\u003eSupplied complete\u003c\/li\u003e\n\u003cli\u003eRelated numbers: 2302HG in light gray, 2302SC with the soft carpet front bottom plate\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eShips in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214477943034,"sku":"2302GS","price":18.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2302GS_48b2cc77-88a3-4513-8cea-1ba56a2b36ba.jpg?v=1785139706"},{"product_id":"bumper-with-soft-carpet-front-bottom-plate-for-et-1-gray-black","title":"SEBO ET-1 Bumper with Soft Carpet Front Bottom Plate — Gray Black","description":"\u003cp\u003eTwo components in a single order: SKU 2302SC pairs the gray black ET-1 bumper with the soft carpet front bottom plate, the front sole piece SEBO supplies for soft, deep-pile flooring. Ordering them together keeps the leading edge of the head matched above and below rather than mixing a new strip against a scarred plate.\u003c\/p\u003e\u003cp\u003eThe two parts do separate jobs on the same edge. Below the line, the front plate governs how the nozzle enters the pile, and the soft carpet version is shaped to stop the head burying itself and gripping on plush flooring where a standard plate would seal down and make the machine heavy to push. Above the line, the bumper takes the impacts from furniture and skirting so the housing never has to. Damage to either is worth addressing as a pair, because both sit on the same leading edge and both shape how the head behaves at the start of every stroke.\u003c\/p\u003e\u003cp\u003eAnyone who has changed flooring to a softer pile tends to want this combination rather than the standard front plate, and it is also the sensible order when a head has been dropped on its nose and both pieces are scarred. Fitment covers the SEBO FELIX Premium, the DART, the C3.1 and the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium, in each case on ET-1 heads built with or without an on\/off rocker. If the front plate is still sound, the bumper alone is part 2302GS in gray black or 2302HG in light gray.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2302SC\u003c\/li\u003e\n\u003cli\u003ePack contents: the bumper plus the soft carpet front bottom plate\u003c\/li\u003e\n\u003cli\u003eColour: gray black\u003c\/li\u003e\n\u003cli\u003eRelated numbers: 2302GS bumper only, 2302HG light gray bumper\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO parts. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214478041338,"sku":"2302SC","price":30.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2302SC_7a9958c8-823c-4dd6-8ee8-9a30ebe0f469.jpg?v=1785137376"},{"product_id":"sliding-button-for-dart-gray-black","title":"SEBO Sliding Button for DART Uprights — Gray Black","description":"\u003cp\u003eThe gray black slider carried under number 7035GS belongs to the SEBO DART and is drawn at item 30 of the DART parts sheet. Reading the sheet in order shows exactly what it belongs to: item 30 is this button, item 31 is the switch frame it runs in, and item 32 is the two-pole rocker switch underneath, carried as part 05138. The button is the visible cap of that stack. Slide it and it drives the rocker over; the frame keeps it square and holds the detent that makes a chosen position stay chosen.\u003c\/p\u003e\u003cp\u003eTwo things go wrong with it. Grit works into the track and the action turns coarse or seizes outright, or the moulded detent rounds off and the button will no longer stay where it is put, creeping under the vibration of a running motor. Neither stops the machine, but a control that drifts is a control changing the setting without being asked. Swapping the button restores a firm, repeatable action, and it is quick work once the handle panel is off.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7035GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e item 30, DART sheet, sliding button\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSits in:\u003c\/strong\u003e the switch frame at item 31, over the two-pole rocker switch 05138 at item 32\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplace it when:\u003c\/strong\u003e the action has gone stiff, the cap rattles in its track, or a setting refuses to stay put\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eWork out which of the three parts has actually failed before ordering, because from outside the handle they present much the same. A button that moves freely but changes nothing points at the rocker switch 05138. A button that will not move points at grit in the track or a snapped tab on the button itself. A button that moves but has lost its positive stop points at either the button or the white switch frame 7178WE. The printed film covering the face of the assembly is 7142 and is worth renewing in the same job, since it rarely survives being lifted once. Genuine SEBO part from an authorized SEBO dealer, shipped in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214478401786,"sku":"7035GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/5959b824c79dabe5eda6f445a6264393.jpg?v=1786669163"},{"product_id":"pile-adjustment-knob-for-et-1-and-et-2-gray-black","title":"SEBO Pile Adjustment Knob for ET-1 and ET-2 Power Heads \u0026mdash; Gray Black","description":"\u003cp\u003eCarpet height on an ET-1 or ET-2 power head is chosen with a single control, and 2931GS is it in gray black. SEBO shows the knob at position 110 on the ET-1\/ET-2 sheet, where the DART list files the same position under pile adjustment button. Turning it steps the brush roll up or down so the bristles meet plush, medium or low carpet at a sensible depth instead of skating over the fibers or stalling in them.\u003c\/p\u003e\u003cp\u003eKnobs catch on furniture legs and split at the hub long before the mechanism underneath gives out. A cracked hub turns without driving the shaft below it, which strands the head on whatever setting it was last left on, and a knob that has gone missing altogether leaves nothing to grip. Fitting a new one restores indexed selection without opening the rest of the adjustment group. If the detents themselves feel mushy rather than the knob feeling loose, look past this part to the spring at 106, part 2929, and to the complete pile adjustment assembly at 107, sold as 2316GS in gray black.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2931GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e gray black, matching the darker head trim\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 110 on the ET-1\/ET-2 sheet, and 110 on the DART list as the pile adjustment button\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther finishes:\u003c\/strong\u003e 2931HG in light gray, 2931SB in silver\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2316GS adjustment assembly, 2929 spring\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eOrder by finish rather than by feel: gray black, light gray and silver knobs share the same fitting but look plainly different on the head. Genuine SEBO part from an authorized dealer, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214480597242,"sku":"2931GS","price":8.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0733ea0293158c3f0fa21738f6b746bf.jpg?v=1786668905"},{"product_id":"release-button-with-leaf-spring-for-et-1-et-2-et-c-et-h-and-disco-swivel-necks-gray-black","title":"SEBO Swivel Neck Release Button with Leaf Spring — Gray Black","description":"\u003cp\u003ePress the neck release and get nothing back — no click, no spring, no release — and the flat spring behind the button has almost certainly cracked. Part 1737GS pairs the gray black button with a fresh leaf spring, so the mechanism is rebuilt rather than patched.\u003c\/p\u003e\u003cp\u003eThe button lives in the swivel neck, the pivoting joint where a power head or floor tool locks onto the machine. Pushing it flexes the leaf spring and withdraws the locking tab; letting go lets the spring drive the tab back into its keeper. Once that spring loses its tension or breaks, the fault shows up in one of two ways. Either the button sinks in and stays down, so the head will not release without a fight, or there is no resistance under the thumb at all and the joint no longer locks, which is felt as a neck that rocks and wanders while the machine is steered. Packed hair and grit in the button recess mimic both symptoms, so it is worth clearing the recess and trying again before condemning the part.\u003c\/p\u003e\u003cp\u003eSEBO draws it at position 117 on both the DART and the FELIX sheets, described on the FELIX drawing as the gray black release button. Button and spring wear as a pair, which is why supplying one without the other would leave half the repair undone.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits machines:\u003c\/strong\u003e SEBO FELIX Premium, FELIX 2 Premium, DART, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits power heads:\u003c\/strong\u003e ET-1 Power Heads (with switch), ET-1 Power Heads (without switch), ET-2 Power Heads (with switch), ET-2 Power Heads (without switch) and ET-C Power Heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso fits:\u003c\/strong\u003e the DISCO Floor Polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied as:\u003c\/strong\u003e button plus leaf spring\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 117 on the DART and FELIX drawings\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 1737GS — order 1737HG for the light gray finish\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part:\u003c\/strong\u003e gray black release button cap 1738GS for ET-C power heads\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO through an authorized dealership, typically shipping in 2–5 business days. Clear hair and grit from the recess first, seat the new spring squarely in its channel, then work the release half a dozen times and confirm the neck locks solidly before the machine goes back to work.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214484070650,"sku":"1737GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/1737GS_b7de5bdb-e63c-4d5a-9b38-aa778abcb519.jpg?v=1785150955"},{"product_id":"grommet-single-for-x1-x2-x4-x5-felix-new-handle-and-dart-gray-black","title":"SEBO Cord Grommet for AUTOMATIC X, FELIX and DART — Gray Black, Single","description":"\u003cp\u003eSometimes only one has perished. Part 5359GS1 is a single gray black grommet for a cord or cable pass-through, and SEBO's AUTOMATIC X4\/X5 parts drawing shows it at item 3, in the group covering the handle and the cord entry next to the cable clamp 5162.\u003c\/p\u003e\u003cp\u003eThe description of the job is short. The grommet lines the hole a cable travels through so that the jacket bears against rubber rather than against a moulded rim. Leave the hole bare and the cable rests on that rim; the small, constant movements a vacuum makes in use then saw the outer sheath at one fixed point until it wears through. That is a slow failure, invisible from the outside, and it usually only comes to light when the machine is stripped for something else entirely. The liner is also what holds the cable still in the panel, so a missing one lets the whole run creep as the machine is pushed and pulled.\u003c\/p\u003e\u003cp\u003eReplacing a single grommet makes sense when the others are still soft and still gripping their panels. If the rubber has hardened generally, the ten-pack under 5359GS covers a whole machine in one go. Either way, unplug at the outlet first and run a finger along the neighbouring length of cable while the panel is open, checking for the flat, shiny patch that says the jacket has been rubbing.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO AUTOMATIC X1, X2, X4, X4 Boost and X5; SEBO FELIX Premium and the FELIX 2 Premium; SEBO DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e moulded rubber cable liner\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 5359GS1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e item 3, AUTOMATIC X4\/X5\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSold:\u003c\/strong\u003e individually\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTen-pack:\u003c\/strong\u003e 5359GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated position:\u003c\/strong\u003e cable clamp 5162, item 8 on the same sheet\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO cable grommet, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214484857082,"sku":"5359GS1","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/29f492ffd45d5ed597fcad805319b7ac.jpg?v=1786668260"},{"product_id":"grommet-10-pack-for-x-series-felix-new-handle-and-dart-gray-black","title":"SEBO Cord Grommet for AUTOMATIC X, FELIX and DART — Gray Black, 10 Pack","description":"\u003cp\u003eTen gray black grommets under one number: 5359GS covers the cable pass-throughs on SEBO's AUTOMATIC X uprights, on the FELIX fitted with the later handle, and on the DART.\u003c\/p\u003e\u003cp\u003eA grommet is the rubber liner that sits in a hole in the moulding wherever a cable has to cross from one section of the machine into another. Its whole purpose is to give the cable a rounded, slightly yielding bearing surface in place of a hard plastic edge. Heat and years take the flexibility out of the rubber; it shrinks, loses its grip on the panel, then splits. From that point the cable lies directly on the rim of the opening, and every push and pull of ordinary use draws the outer jacket across it until the sheath thins and the insulation beneath is at risk. On a machine that has already lost one, the cable is usually marked at exactly that spot.\u003c\/p\u003e\u003cp\u003eAnybody who opens one of these machines tends to find the whole set in the same state, which is the case for buying ten rather than one: renew every pass-through in the machine in a single visit and keep the balance for the next service. Disconnect the machine from the outlet before touching anything on the cord run. On the AUTOMATIC X uprights this grommet is catalogued in the same handle and cord-entry group as the cable clamp 5162 and the switch cap holder 5161GS, which is a useful landmark when working from the parts drawing.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO AUTOMATIC X1, X2, X4, X4 Boost, X5, X7 Premium and X8; SEBO FELIX Premium and the FELIX 2 Premium; SEBO DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e moulded rubber cable liner\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack:\u003c\/strong\u003e 10 grommets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 5359GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSingle unit:\u003c\/strong\u003e 5359GS1, shown at item 3 on SEBO's AUTOMATIC X4\/X5 diagram\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO parts, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214485184762,"sku":"5359GS","price":8.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/f1712a4eb35d12480796852ba5d854cf.jpg?v=1786668255"},{"product_id":"power-supply-cord-for-felix-and-dart-dark-gray","title":"SEBO Power Supply Cord for FELIX and DART Uprights - Dark Gray","description":"\u003cp\u003eCords fail in ordinary, visible ways: a jacket nicked on a doorframe, a flattened length where a chair leg has been parked for a year, a plug that runs warm or will not sit tight in the outlet. The dark gray supply lead SEBO specifies for the DART, the FELIX Premium and the FELIX 2 Premium is ordered as 7127DG.\u003c\/p\u003e\u003cp\u003eNothing else on an upright takes comparable punishment. The lead gets hauled around corners, run over by the machine it belongs to, pulled out of the wall by the cable instead of the plug, and wound onto its hooks while still warm and pulled tight. Damage to insulation is a question of safety, not performance, so exposed conductors, a split plug body or scorching at the pins mean the machine goes out of service that day rather than getting taped up and carried on with. There is a diagnostic reason to change one as well: a lead that conducts only at certain angles is the classic explanation for an upright that seems to die and come back at random, and it is far cheaper to rule out than the electronics behind it.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7127DG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eListed for:\u003c\/strong\u003e the SEBO DART, the FELIX Premium and the FELIX 2 Premium\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e dark gray\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplace it when:\u003c\/strong\u003e the outer jacket is cut or worn through, the plug is loose, discolored or scorched, or power comes and goes as the lead is flexed\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting:\u003c\/strong\u003e hard-wired at the machine end, so this is a technician's job and not a plug-in swap\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe internal wiring that takes over from it is 7064, listed for the same three uprights and drawn at item 2 of the DART sheet. Storage hooks are separate items in the finish of each machine, at item 15 on the FELIX sheet and item 19 on the DART sheet, so a snapped hook does not have to mean living with a trailing cord.\u003c\/p\u003e\u003cp\u003eGenuine SEBO lead supplied by our authorized dealership. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214486298874,"sku":"7127DG","price":41.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/7127DG_0883ae8e-e669-4462-891f-36cccf088b1a.jpg?v=1785138549"},{"product_id":"wiring-for-swivel-neck-for-et-1-et-2-and-disco","title":"SEBO Swivel Neck Wiring for ET-1, ET-2 and DISCO Power Heads","description":"\u003cp\u003eOf all the wiring inside a power head, the run through the swivel neck is the one that actually moves. It twists and flexes with every turn of the head and every change of direction, and part 0876ER is the pre-made loom SEBO supplies for exactly that section.\u003c\/p\u003e\u003cp\u003eFlex fatigue is gradual and then sudden. Strands break one at a time inside insulation that still looks perfect, so the brush roll starts cutting out at a particular angle of the handle, comes back when the head is straightened, and eventually stops for good. Fits the ET-1 and ET-2 power heads in both switched and unswitched builds, the DISCO Floor Polisher, and the machines these heads are supplied on: FELIX Premium, FELIX 2 Premium, DART, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and the C3.1.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e SEBO 0876ER, swivel neck wiring\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 114 on the SEBO ET 1 \/ ET 2, DART and FELIX sheets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTypical fault:\u003c\/strong\u003e the roller drops out as the head is steered, then returns when it is straightened\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied:\u003c\/strong\u003e made up to length with its terminations already fitted\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated power head wiring:\u003c\/strong\u003e 0880 for the safety switch with its lead, 0881 for the board-to-switch harness\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMachines these heads ship on:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eWork the new loom through the neck's full range of movement before the housing goes back together, so nothing is trapped, stretched or pinched at the extremes of travel. Repeating the original routing matters more here than anywhere else in the machine, because this is the one length of wire that will be bent several thousand times a year.\u003c\/p\u003e\u003cp\u003eGenuine SEBO swivel neck wiring for ET-1 and ET-2 power heads, ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214487118074,"sku":"0876ER","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0876ER.jpg?v=1785156314"},{"product_id":"internal-wiring-et-for-felix-series-and-dart","title":"SEBO Internal Wiring ET Harness for FELIX Premium, FELIX 2 Premium and DART","description":"\u003cp\u003ePart 7064 is the harness SEBO designates ET internal wiring: the loom threading supply and switching down the inside of a DART, FELIX Premium or FELIX 2 Premium. It appears at item 2 on the DART sheet, right at the head of the drawing, since practically every electrical component below depends on what this loom delivers.\u003c\/p\u003e\u003cp\u003eThe sheet also shows where it hands over. At item 114 the swivel neck wiring 0876ER continues the run into the neck, and at item 125 the micro safety switch 0880 sits in that path; beyond them the supply reaches the power head. Nothing in a loom like this stays still. It bends with each movement of the handle, spends its life beside a motor cycling between hot and cold, and is pinched by a clip at every change of direction. Given enough years, individual strands snap inside insulation that shows no mark at all, and crimps quietly loosen.\u003c\/p\u003e\u003cp\u003eWhat the owner sees is a fault with no fixed address: running one minute, silent the next, alive again after the handle is moved or the neck swung across. Hunting that down with a meter takes a long time, and mending one broken conductor in an old loom generally buys a few months before the next one goes. A new harness closes the chapter.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7064\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitment:\u003c\/strong\u003e SEBO DART, FELIX Premium and FELIX 2 Premium\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDescription:\u003c\/strong\u003e ET internal wiring loom\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e item 2, DART sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSymptom:\u003c\/strong\u003e intermittent power that shifts as the handle or the neck is moved\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 0876ER swivel neck wiring, 0880 micro safety switch, 7041ER vacuum motor\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eTake photographs of the run before anything is pulled out; clip positions and the sequence in which conductors cross are impossible to reconstruct once the loom is loose on a bench. Pull the plug first and keep it out for the duration. Genuine SEBO harness from an authorized SEBO dealer, dispatched in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214488232186,"sku":"7064","price":12.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/6603496e6532ccbb548b7f9f063ed4b4.jpg?v=1786669025"},{"product_id":"internal-cable-for-dart-and-felix-1-9802am-with-non-adjusting-handles","title":"SEBO Internal Cable for DART with Non-Adjusting Handle","description":"\u003cp\u003eHandle design, not model year, decides which internal lead a SEBO DART needs. Part 7070 is the internal cable specified for DART uprights built with the fixed, non-adjusting handle, where the wiring run inside the tube stays one constant length instead of extending and retracting with an adjustable grip.\u003c\/p\u003e\u003cp\u003eThe cable carries mains current from the body of the machine up to the switch in the handle, so it lives inside the tube and flexes in the same two or three places every time the vacuum is used. Failure is quiet rather than dramatic. Strands break one at a time where the conductor enters a terminal, or a crimp works loose and begins arcing under the insulation. What an owner notices is a machine that cuts out when the handle is moved, comes back when it is nudged, then behaves perfectly for a fortnight. None of that is visible from outside, which is why a new cable is the sensible repair rather than a hunt for damage sealed inside the sheath.\u003c\/p\u003e\u003cp\u003eSEBO's DART exploded diagram draws the machine's internal wiring ET at item 2, supplied as part 7064, and 7070 is the cable listed for the non-adjusting handle build. The rest of that group on the same sheet gives you the neighbouring numbers worth checking while the tube is open: the tube plug 7076GS at item 27, the complete handle 7164WE at item 28, the sliding button 7035GS at item 30, the switch frame 7178WE at item 31, the two-pole rocker switch 05138 at item 32 and the protection film 7142 at item 39. If the tube itself is bent, the DART takes the 660 mm fixed handle tube, part 7080ER.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitment:\u003c\/strong\u003e SEBO DART uprights with the non-adjusting handle\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7070, internal cable\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e carries current between the machine body and the handle switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplace when:\u003c\/strong\u003e power is intermittent, the vacuum cuts out as the handle moves, or a terminal shows heat discolouration\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 7064 internal wiring ET, 7080ER handle tube, 05138 rocker switch, 7142 protection film\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003ePull the plug from the wall and identify which handle style you have before you order, because adjusting-handle machines run a different lead. This is a genuine SEBO DART internal cable replacement supplied by an authorized SEBO dealer, dispatched in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214488330490,"sku":"7070","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/7070.jpg?v=1785154334"},{"product_id":"dust-bag-housing-for-dart-felix-series-and-felix-ice-blue-new-and-old-handle-configuration","title":"SEBO Dust Bag Housing for FELIX Premium, FELIX 2 Premium and DART Uprights","description":"\u003cp\u003ePart 7143ER is the moulded compartment the filter bag lives inside on a SEBO upright — the chamber the bag collar slides into, not the door that shuts over it and not the bag itself. A single number covers three machines: the FELIX Premium, the FELIX 2 Premium and the DART, in both the newer and the earlier handle configurations, and including the Ice Blue finish. That breadth is why one part turns up on repair orders for machines of very different ages.\u003c\/p\u003e\u003cp\u003eThree faults send people looking for a bag housing. Impact damage from a fall, or from a hard knock against a stair nosing. A crack radiating out of a screw boss, usually after the compartment has been forced shut once too often. And a sealing face pushed out of shape until the collar can no longer sit flat in it. All three do the same thing: they open a route for air to reach the motor without passing through the bag first. The machine keeps running and can even sound stronger for it, while dust that should have been captured travels on into the pre-motor filter and past it.\u003c\/p\u003e\u003cp\u003eWorth ruling out before ordering. On SEBO's FELIX drawing the door that closes over this chamber is a separate colour-matched item at position 16 (7093SW in black), the filter cover is position 17, and the small spring holding that door shut is the cover latch spring at position 29, part 7024ER. A compartment that keeps springing open in use is usually one of those three rather than the housing behind them. A compartment that whistles, or that leaves fine dust on the pre-motor filter after every job, is the housing.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO FELIX Premium, FELIX 2 Premium and DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCovers:\u003c\/strong\u003e both the new and the old handle configurations\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7143ER\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWhat it does:\u003c\/strong\u003e forms the sealed bag chamber and locates the bag collar\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplace when:\u003c\/strong\u003e the chamber is split, a boss has broken away, or the sealing face will not hold the collar square\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated numbers:\u003c\/strong\u003e 7012AM pre-motor filter (position 42 on the FELIX sheet, 13 on the DART), 7029AM AeraPure filter bag (position 22, DART sheet)\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eSEBO 7143ER, FELIX dust bag housing, DART bag compartment replacement: all of those describe this one item, and it is the same part whichever of the three uprights it is going into. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214492000506,"sku":"7143ER","price":32.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/104b8915e19d9a8b2ab099afa6c29036.jpg?v=1786669109"},{"product_id":"cord-hook-for-felix-white-dart-and-rose-white","title":"SEBO Cord Hook for FELIX Premium and DART Uprights — White","description":"\u003cp\u003eWhite is the widest-reaching version of this moulding. Part 7027WE covers both the SEBO FELIX Premium and the SEBO DART, where most of the other shades are tied to a single trim, and SEBO draws it at item 19 on the DART sheet listed simply as the cable hook.\u003c\/p\u003e\u003cp\u003eIt clips to the handle tube and gives the wound mains lead somewhere to sit. The failure is always mechanical and always the same: the moulded stem cracks where it meets its base, either from years of cord tension or from one hard pull at the wrong angle. Nothing about the machine's cleaning changes afterwards, which is why a broken hook so often lives on a shelf for months. The real cost falls on the cord, because a lead that is draped rather than hooked drops to the floor, gets stood on, and loosens its insulation at the point where it enters the body.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7027WE\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO FELIX Premium and SEBO DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e white\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e item 19, DART sheet, cable hook\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso in the white group:\u003c\/strong\u003e 7090WE hose duct, 7164WE handle grip, 7091WE filter cover\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSame hook in other finishes:\u003c\/strong\u003e 7027SW black, 7027GS gray black, 7027DR red, 7027DB dark blue\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eOrdering by colour rather than by model is the reliable approach with this part, because the hook geometry is shared across the trims and only the shade changes between numbers. While the cord is off the machine, look hard at the second hook as well as the broken one: a stem that has gone chalky white or shows a hairline at the base is running on the same clock. Nearby on the DART drawing are the valve spring set 7028ER at item 17 and the AeraPure filter bag 7029AM at item 22, both of which are worth having in the same order if the machine is due a service. Genuine SEBO stock from an authorized SEBO dealer, delivered in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214494425338,"sku":"7027WE","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/bd48e90487a344abc7fccff945b60d53.jpg?v=1786668998"},{"product_id":"air-duct-for-dart-gray-black","title":"SEBO Air Duct for the DART Upright — Gray Black","description":"\u003cp\u003e7002GS is the gray black air duct made for the SEBO DART: the rigid internal channel that carries the airstream through the body of the upright on its way to the filtration.\u003c\/p\u003e\u003cp\u003ePut it in the run and it explains itself. Dirt leaves the cleaning head, travels this channel, and lands in the AeraPure bag listed at position 22 of the DART parts sheet as 7029AM, which hangs in bag housing 7143ER. From there the air crosses pre-motor filter 7012AM at position 13, goes through the motor, and finally passes the exhaust filter at position 24, which clamp 7017GS holds down; SEBO's marine blue exhaust microfilter with textile for this machine is 7095AM08. Above-floor cleaning takes the same route through hose 7050SB at position 33, with retaining ring 7018OR at 38 and tube plug 7076GS at 27.\u003c\/p\u003e\u003cp\u003eRigid ducting does not wear out gradually the way a belt or a brush strip does. It fails at a point: a seam splits after the machine has been dropped or wedged into a doorframe, or something solid lodges in the bend and stays there. Both faults produce the same odd report — the motor sounds exactly as it always has, the bag is not full, the filters are clean, and the nozzle has stopped lifting anything. A split lets the motor draw easy air from inside the machine rather than hard air from the carpet; a blockage simply throttles it. Either way the pull that reaches the floor is gone.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7002GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitted to:\u003c\/strong\u003e SEBO DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction:\u003c\/strong\u003e internal air channel carrying dirt from the cleaning path to the bag chamber\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSame airway:\u003c\/strong\u003e 7050SB hose, 7018OR retaining ring, 7076GS tube plug, 7143ER bag housing\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConsumables downstream:\u003c\/strong\u003e 7029AM filter bags, 7012AM pre-motor filter\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplace when:\u003c\/strong\u003e the channel is split, distorted, or permanently obstructed\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA SEBO DART air duct, a gray black airway moulding and a DART suction loss repair are all descriptions of this component. Factory SEBO moulding, authorized dealer stock, sent out in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214499766522,"sku":"7002GS","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/a0129ba8d0d774c369681db879dfbd75.jpg?v=1786669160"},{"product_id":"hose-duct-for-felix-white-dart-and-rose-white","title":"SEBO Hose Duct for FELIX Premium and DART Uprights — Arctic White","description":"\u003cp\u003eTwo different SEBO uprights take this same duct. The FELIX Premium and the DART both use part 7090WE, moulded in the arctic white SEBO applies to its lighter bodies, and the FELIX exploded diagram lists it at item 14.\u003c\/p\u003e\u003cp\u003eFunctionally it is the rigid section that accepts air at the hose connection and turns it through into the bag compartment. That puts it at a stress point. The hose is levered against it whenever the tools are in use, and the assembly is loaded again each time the machine gets towed rather than carried. Flex a moulding that way for a decade and it cracks at the collar or opens along a seam. Neither failure makes a noise anyone notices, and both drain suction from the wand while letting fine debris out of the airway well before the bag.\u003c\/p\u003e\u003cp\u003eBoth machines carry the same components either side of it. The hose is 7050SB, with the retaining ring and spring 7018OR clamping its cuff, drawn at item 27 on the FELIX sheet and item 38 on the DART sheet. The pre-motor filter 7012AM appears at item 42 in the FELIX drawing and item 13 in the DART drawing, and bags for both arrive as the 7029AM filter bag box. Pairing with this duct in the same finish is the arctic white filter cover 7091WE.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitment:\u003c\/strong\u003e SEBO FELIX Premium uprights and the SEBO DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour and finish:\u003c\/strong\u003e arctic white\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7090WE\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e item 14 on SEBO's FELIX sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplace when:\u003c\/strong\u003e the joint sings under load, the hose end has gone loose, or a crack is visible\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 7050SB hose, 7018OR retaining ring, 7091WE filter cover, 7029AM filter bags, 7012AM pre-motor filter\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA direct-fit genuine SEBO part, stocked by an authorized SEBO dealer and dispatched in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214500323578,"sku":"7090WE","price":18.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/7090WE.jpg?v=1709348383"},{"product_id":"lower-housing-for-dart-white","title":"SEBO Lower Housing for DART Upright — White","description":"\u003cp\u003eEvery baseboard, chair leg and door frame a DART meets is met by its lower body shell, and after enough of them the shell is what gives — a screw boss opened out, a split rib, a corner gone entirely. 7169AM is SEBO's white replacement for it.\u003c\/p\u003e\u003cp\u003eWhite is a full trim family on this machine rather than a one-off. SEBO lists the handle complete as 7164WE, the switch frame as 7178WE, the cord hook as 7027WE and the power head cover with DART print as 2331WEAM, all for the DART. This lower housing is the same finish, which matters because a mismatched shell is the most visible repair you can make to an upright. For reference, the equivalent row on SEBO's FELIX sheet is drawn in black (7173SE) and dark blue (70166SE); those are separate numbers.\u003c\/p\u003e\u003cp\u003eKeep the body shell and the floor head apart in your head when diagnosing. SEBO numbers the DART's ET-1 power head hardware from row 100 upwards — chassis 2324GS, brush roller 5010AM, belt 2923 and the bearing blocks 2314GS and 2313GS — and each of those is its own order. A clattering, brush-related noise usually belongs to that group. What belongs to the lower housing is a body that flexes, fasteners that will not tighten because their bosses have opened out, cracks radiating from an impact point, and rattles that move with the machine rather than with the brush.\u003c\/p\u003e\u003cp\u003eWith the machine open it is worth checking the pre-motor filter 7012AM, the box of eight AeraPure bags 7029AM and the hose 7050SB, all listed for the DART.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitment:\u003c\/strong\u003e SEBO DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShade:\u003c\/strong\u003e white\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWhat it is:\u003c\/strong\u003e the lower body shell of the upright, supplied on its own\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eChange it when:\u003c\/strong\u003e the shell is cracked, screw bosses no longer hold, or the body feels loose in use\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMatching trim and service numbers:\u003c\/strong\u003e 7164WE handle, 7178WE switch frame, 7027WE cord hook, 2331WEAM power head cover, 7012AM pre-motor filter\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO component, dispatched in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214500454650,"sku":"7169AM","price":20.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/ca83c29700e22320cbf4eb068dc46af9_de78bdd4-548b-47cb-933d-2f9c8a35a78e.jpg?v=1786669187"},{"product_id":"power-head-cover-for-et-1-with-dart-print-white","title":"SEBO ET-1 Power Head Cover with DART Print - Arctic White","description":"\u003cp\u003eDART machines carry a printed shell of their own, and 2331WEAM is it. SEBO gives the finish its own name in the parts book, arctic white, and prints the DART wordmark across the top face of the ET-1 power head cover.\u003c\/p\u003e\u003cp\u003ePosition 132 is where it sits in the DART diagram, which is worth noting if you are working from the sheet rather than from the number, since most of the ET-1 covers are drawn at 135 on their own diagrams. The cover itself is the molded upper half of the nozzle, screwed and clipped down over the drive side, sealing the belt and pulley away from the grit the machine is picking up an inch below. Replace it when a corner has broken out, when a fixing point has cracked and the top no longer pulls down tight, or when the printed surface has worn away and the head looks tired next to the rest of the machine. A cover that cannot seat flush lets the housing flex, and that flex ends up in the belt path.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2331WEAM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor and finish:\u003c\/strong\u003e arctic white, SEBO's own name for the shade, with the DART print applied\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e the SEBO DART, and ET-1 power heads whether switched or unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 132, DART parts diagram\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied as:\u003c\/strong\u003e the shell alone, sold singly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNot included:\u003c\/strong\u003e brush roller, belt, switch or fixings\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther white shells:\u003c\/strong\u003e 2326WEET in plain white, and 2331WESE, the other printed white version\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe print is the only thing separating this from the other white ET-1 covers in the range, and photographs rarely show it clearly, so order by number. Searches for a SEBO DART power head cover replacement, or for a genuine SEBO arctic white ET-1 cover, both point here. If a fixing is beyond reuse, SEBO lists its hardware individually too, with screw 3.9 x 16 as 0103 and 0103ER for a ten pack. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214502027514,"sku":"2331WEAM","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/740d84c7c2d64bf5a84b83450959ac06.jpg?v=1786669152"},{"product_id":"retaining-ring-with-spring-for-felix-series-and-dart-hose-orange","title":"SEBO Hose Retaining Ring with Spring for FELIX Premium, FELIX 2 Premium and DART — Orange","description":"\u003cp\u003eSEBO's orange collar 7018OR arrives with the spring that loads it, and between them they hold a hose end captive in the machine body. Seat the hose and the spring pushes the collar into a groove around the cuff; operate the release and the collar retreats far enough to free it. Both drawings show the same assembly: item 38 on the DART sheet, item 27 on the FELIX sheet, the latter listed as retaining ring complete.\u003c\/p\u003e\u003cp\u003eWhat fails is the load, not the moulding. Owners describe a hose that gradually slides out under its own weight while attachments are in use, or one that seats with a convincing click and then lets go at the first proper pull on the wand. There is a quieter version too: a collar that no longer clamps hard leaves the joint whistling, so the tools go weak while the floor nozzle behaves normally, which sends people to the bag and the filters for nothing. Since a slack spring and a worn collar look identical from outside, SEBO does not split them into separate numbers.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7018OR\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitment:\u003c\/strong\u003e SEBO DART, FELIX Premium and FELIX 2 Premium\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied as:\u003c\/strong\u003e collar and spring together\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e orange\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e DART sheet item 38, FELIX sheet item 27\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSymptoms:\u003c\/strong\u003e a hose that works loose, refuses to latch, or leaks air at the joint\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 7050SB complete hose at item 33, 7028ER valve spring set at item 17\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eOrange marks the components SEBO expects a user to handle, which is why the 2937OR foot pedal and the 2909VO access door on the power head wear the same shade. Examine the hose cuff for scoring once the collar is off: a scored cuff will grind through a fresh collar exactly as it did the last one, and at that point the complete hose 7050SB is the honest repair. Authorized SEBO dealer stock, dispatched in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214504419578,"sku":"7018OR","price":8.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/c239b1fd503409339ae7d25759651af4.jpg?v=1786668976"},{"product_id":"access-door-with-axle-and-spring-for-et-1-and-et-2-orange","title":"SEBO Access Door with Axle and Spring for ET-1 and ET-2 Power Heads \u0026mdash; Orange","description":"\u003cp\u003eET-1 and ET-2 power heads pass this hinged door on to every machine built around them, which is why one orange component covers so much of the SEBO range. Part 2909VO ships complete with its axle and spring, and SEBO puts it at position 108 on the ET-1\/ET-2, DART and FELIX parts sheets alike.\u003c\/p\u003e\u003cp\u003eThe door is what gets opened for belt and brush access, so its hinge sees more cycles than almost anything else on the head. As the spring slackens or the axle wears its bore oval, the door stops sitting flush: it hangs open a few millimetres, drags on carpet as the head is pulled back, rattles over hard floors, and eventually breaks at the pivot where the plastic has been working. Fitting the assembled part restores the pivot and the closing tension in one go, with no hardware to transfer across from a broken door and nothing to line up by hand.\u003c\/p\u003e\u003cp\u003eFull fitment runs to the SEBO ET-1 and ET-2 power heads in both the with-switch and without-switch versions, the FELIX Premium and FELIX 2 Premium, the DART, the AIRBELT D4 PREMIUM, the AIRBELT E3 Premium, the AIRBELT K3 PREMIUM and the C3.1. Behind the same door sit the parts most often replaced with it: toothed belt 2923, axle 2928, spring 2929 and orange foot pedal assembly 2937OR. Roller sizes split by head — the 12 inch 5010AM covers the ET-1 heads, FELIX Premium, DART, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1, while the ET-2 heads and the FELIX 2 Premium take the 15 inch 2838AM. Searches for a SEBO access door with its axle and spring fitted, an ET-1 belt door or a FELIX brush access door land here.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSEBO part 2909VO — hinged access door, axle and spring included\u003c\/li\u003e\n\u003cli\u003eFits: SEBO ET-1 and ET-2 power heads (with or without switch), FELIX Premium, FELIX 2 Premium, DART, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1\u003c\/li\u003e\n\u003cli\u003eColor: orange\u003c\/li\u003e\n\u003cli\u003eParts-diagram position: 108 on the ET-1\/ET-2, DART and FELIX sheets\u003c\/li\u003e\n\u003cli\u003eTypical symptom: a door that will not latch flush, drags on carpet, or has snapped at the hinge\u003c\/li\u003e\n\u003cli\u003eRelated part numbers: 2923 belt, 2928 axle, 2929 spring, 2937OR foot pedal with axle and spring\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine SEBO\u003c\/strong\u003e; ships in 2–5 business days\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214507041018,"sku":"2909VO","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2909VO_bbb0cc33-49e9-460f-8834-32029ed2e7b1.jpg?v=1785150214"},{"product_id":"chassis-for-et-1-gray-black","title":"SEBO ET-1 Power Head Chassis — Gray Black","description":"\u003cp\u003eEverything inside an ET-1 head bolts to the chassis: motor, roll bearings, wheels and the height linkage all take their alignment from it. Part 2324GS is that frame in gray black, supplied as the frame alone so the original internals move across into it.\u003c\/p\u003e\u003cp\u003eA split screw boss or a frame twisted by a hard fall puts the roll out of parallel with the floor, and no set of new bearings will correct that. The symptoms are the ones that survive every other repair: a head that still runs noisy after fresh bearing blocks, a belt that keeps tracking off despite a new pulley, uneven bristle wear across the strip, or a wheel mount that no longer holds its position. Stairs account for most of the damage, followed by heads that have been leaned on while the machine was parked upright. SEBO shows the ET-1 chassis as position 100 in the DART diagram.\u003c\/p\u003e\u003cp\u003eAllow proper time for the transfer and keep fasteners grouped by where they came from, because the same screw is not always used at every location. Inspect the bearing blocks, the belt and the pulley while the internals are out, since all three are far easier to reach with the frame stripped than they will ever be again. Fitment covers the SEBO FELIX Premium, DART and C3.1 uprights and the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium canisters. Light gray heads take chassis 2324HG.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2324GS\u003c\/li\u003e\n\u003cli\u003eColour: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 100, DART parts list\u003c\/li\u003e\n\u003cli\u003eSupplied as the bare frame; original internals transfer across\u003c\/li\u003e\n\u003cli\u003eRelated number: 2324HG in light gray\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO part. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214508777722,"sku":"2324GS","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/298c2e475930d6a048e10c3c4addee01.jpg?v=1786668867"},{"product_id":"cover-dust-bag-housing-for-dart-with-non-adjusting-handle-white","title":"SEBO Dust Bag Housing Cover for DART with Non-Adjusting Handle - White","description":"\u003cp\u003ePart number 7092WE is the white bag door fitted to a SEBO DART built with the fixed handle, the panel that swings open at the front of the body every time a filter bag comes out. SEBO qualifies this cover by handle style rather than by year or badge, so the thing to look at before ordering is your own handle: if it does not adjust for height, this is the cover the machine was built with.\u003c\/p\u003e\u003cp\u003eLatched shut, the panel closes the bag chamber tightly enough that the suction motor has no route into the airstream except straight through the paper bag. The catch faces carry that load every second the machine runs, helped by the small springs SEBO sells as latch spring set 7024ER, and they are where a tired panel gives up first. Rounded catches, a fracture creeping out of a hinge corner, an edge that sits proud of the body: from any of those the machine starts breathing through the gap instead of the bag. Pickup on carpet drops away, a gray line of dust builds along the seam, and the bag stops filling evenly.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7092WE\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO DART uprights built with the non-adjusting handle\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e white\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction:\u003c\/strong\u003e closes and seals the filter bag chamber\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eChange it when:\u003c\/strong\u003e the panel is cracked, will not stay latched, or leaks dust at its edge\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOrdering note:\u003c\/strong\u003e 7092GW is the equivalent white cover carried under a separate number for the other fixed-handle build, so quote 7092WE for the DART\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eMost of what sits behind this door is worth checking while it is off. The molded shell the bag sits in is 7143ER, the latch springs are 7024ER, and the bagged dust goes into the AeraPure bags SEBO packs as 7029AM, all of which are listed for the DART. If the machine has been knocked around, white filter cover 7091WE and white handle set 7164WE keep the finish consistent. Genuine SEBO stock supplied through our authorized dealership. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214512382202,"sku":"7092WE","price":22.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/5ec20fb71a656ad6cd804c1efc2939c7_651fde2b-eca5-4434-b852-fc0c660201a9.jpg?v=1786669177"},{"product_id":"valve-cover-for-dart-and-felix-1-9802am-with-non-adjusting-handles-light-gray","title":"SEBO Valve Cover for DART — Light Gray, Non-Adjusting Handle","description":"\u003cp\u003eThis one is matched by build rather than by badge. 7057HG is SEBO's light gray valve cover for a DART fitted with the fixed handle that does not adjust. Confirm the handle style first, because the gray black panel 7056GS is a separate moulding under a separate number and the two do not swap.\u003c\/p\u003e\u003cp\u003eThe cover seals and positions the valve portion of the airway, keeping that stretch closed so the motor pulls through the nozzle instead of through the machine's own body. Being plastic, and sitting at the joint between body and handle, it is the first casualty when an upright goes over or the neck clips a stair edge. Afterwards nothing sounds wrong at all, which is precisely the difficulty. Only the pickup at floor level betrays it, as part of the airflow now enters through the crack.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7057HG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO DART with the fixed, non-adjusting handle\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e light gray\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e moulded plastic panel located by tabs\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConfirm first:\u003c\/strong\u003e that the handle on the machine does not adjust\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 7056GS gray black valve cover, 7028ER valve spring set\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eUnderneath, the valve is returned by a spring, sold as the 7028ER set with the earlier and later patterns in one packet, and it forms the other half of any investigation that starts with pickup falling off for no reason. Other light gray and white items listed for these machines include the switch frame 7178WE and the tube plug 7076GS. Ease the tabs out carefully during removal; on an aged panel they snap first, and they are what makes the difference between a cover that seals and one that just sits there. Genuine SEBO part from an authorized SEBO dealer, shipped in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214516969722,"sku":"7057HG","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/d0084d0479f93643a6df814a33489dcf.jpg?v=1786669165"},{"product_id":"button-cover-for-premium-parquet-brush-7200gs-gray-black","title":"SEBO Button Cover for the Premium Parquet Brush — Gray Black","description":"\u003cp\u003eSEBO's Premium Parquet Brush, part 7200GS, carries a small gray black cap over its button, and that cap is the piece that absorbs the wear a thumb delivers over a few thousand uses. It is catalogued as 7212GS and drawn at position 64 of the FELIX parts sheet, where the factory names it the button cover for the 7200GS brush. Position 63 on the same sheet is the brush itself, which is a useful way to confirm you are ordering the cap for the right tool.\u003c\/p\u003e\u003cp\u003eCaps of this size fail in three familiar ways. The moulded surface polishes smooth until the button is hard to find by feel, the edge splits and lifts, or the cover departs entirely and leaves the mechanism beneath open to grit and knocks. None of that stops the brush working, but the action stops feeling definite, and an uncovered button collects the dust that eventually makes it sticky. Fitting the replacement cap is a few seconds of work and restores a clean, positive press.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits SEBO:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, AIRBELT D1 TURBO, AIRBELT D4 PREMIUM, AIRBELT E1 KOMBI, AIRBELT E2 TURBO, AIRBELT E3 Premium, AIRBELT K2 KOMBI, AIRBELT K2 TURBO, AIRBELT K3 PREMIUM, C1.1 and C2.1, and C3.1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFor the tool:\u003c\/strong\u003e Premium Parquet Brush 7200GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 64 on the FELIX parts drawing\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSold:\u003c\/strong\u003e one cover\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated wear part:\u003c\/strong\u003e brush strip set 7207ER, two strips with end caps for the same 7200GS brush\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplace when:\u003c\/strong\u003e the cap is cracked, worn featureless, loose in its recess, or lost\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eCheck the number moulded into the underside of your parquet brush before ordering, since SEBO uses different caps across its tool range and 7212GS is specific to the 7200GS. Genuine SEBO parquet brush button cover, supplied by an authorized dealer. Ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214517690618,"sku":"7212GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/a17fc834b46d770142c100fa35fb5064.jpg?v=1786669143"},{"product_id":"filter-cover-for-felix-ice-blue-white-dart-and-rose-white","title":"SEBO Filter Cover for FELIX Premium, FELIX 2 Premium and DART — Arctic White","description":"\u003cp\u003eOne arctic white panel covers the exhaust filter bay on three different SEBO uprights, and 7091WE is that panel. It serves the FELIX Premium, the FELIX 2 Premium and the DART alike, and SEBO draws it at item 17 of the FELIX exploded diagram as the arctic white filter cover.\u003c\/p\u003e\u003cp\u003eClamping the filter is the entire function. Crack the panel or lose a retaining tab and the media no longer sits tight in its recess, letting some proportion of the exhaust slip out around the edge unfiltered. This one is easy to miss because suction is completely unaffected, so the machine gives no hint that anything has changed. The evidence turns up elsewhere: dust returning to the room, a filter that moves when pressed through the closed panel, and a bay lip that no longer wipes clean. Nothing else in the housing can substitute for a cover that has stopped clamping.\u003c\/p\u003e\u003cp\u003eBehind it, the exhaust filter appears at item 41 of the FELIX sheet with the pre-motor filter 7012AM at item 42, while the DART sheet places that same pre-motor filter at item 13 and its own exhaust filter at item 24. Fitting fresh media before the panel goes back on is the sensible order of work. Among the other white parts, the bag housing cover is 7093WE, the complete handle is 7164WE and the hose duct is 7090WE, with bags supplied as the 7029AM filter bag box.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitment:\u003c\/strong\u003e SEBO FELIX Premium, FELIX 2 Premium, DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour and finish:\u003c\/strong\u003e arctic white\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7091WE\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e item 17, arctic white filter cover\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e keeps the exhaust filter square and pressed onto its seat\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 7012AM pre-motor filter, 7029AM filter bag box, 7164WE complete handle, 7093WE bag housing cover\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eDirect-fit genuine SEBO replacement, held by an authorized SEBO dealer and dispatched in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214519984378,"sku":"7091WE","price":24.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/389a052925194cdc963663be922ae3f7.jpg?v=1786669079"},{"product_id":"button-cover-on-et-1-for-dart-gray-black","title":"SEBO Release Button Cover for the DART and ET-1 Power Head — Gray Black","description":"\u003cp\u003eGray black moulded plastic caps the release button on the ET-1 power head, and 2962GS is the factory replacement SEBO supplies for it. The cap spreads pressure from a foot or a thumb across the button underneath and keeps the dust a working head throws around out of the release mechanism. SEBO fits it to the DART and to ET-1 power heads in both the switched and the unswitched build, and the gray black finish is what matches it to the neck hardware around it rather than to the coloured power head shells.\u003c\/p\u003e\u003cp\u003eSEBO draws the button cover as item 118 on the DART parts sheet. Immediately below it at 117 sits the release button with its leaf spring, part 1737GS, and the socket cover for the TS neck is alongside at 120 as part 2961GS; all three come into view in the same strip-down, so it is worth looking at the set together. Worn caps go glassy and slick, and the foot slides off mid-press. Cracked ones let the button rock in its aperture, and the release loses its clean single-press action — usually described as a neck that refuses to let go first time. A cap that has broken away completely leaves the button stem open to grit, and the mechanism stiffens from there.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2962GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e the SEBO DART, and ET-1 power heads with or without the switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 118 on the DART parts sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction:\u003c\/strong\u003e protective cap over the neck release button\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated numbers:\u003c\/strong\u003e 1737GS release button with leaf spring at 117, 2961GS socket cover at 120\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied:\u003c\/strong\u003e as a single cover\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA search for a SEBO button cover, a DART release button cap or simply for part 2962GS lands on this same small component, and swapping it takes minutes once the head is on the bench and the neck hardware is exposed. Supplied genuine by an authorized SEBO dealer, shipping in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214525849850,"sku":"2962GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2962GS.jpg?v=1709347866"},{"product_id":"socket-cover-ts-neck-on-et-1-for-dart-gray-black","title":"SEBO TS-Neck Socket Cover for the DART and ET-1 Power Head \u0026mdash; Gray Black","description":"\u003cp\u003eDART owners replacing the socket cap on the ET-1 head need this exact version, 2961GS in gray black. It closes over the electrical socket in the TS-neck so the contacts feeding the brush motor stay covered while the head swivels along underneath the machine.\u003c\/p\u003e\u003cp\u003eSEBO's DART parts diagram carries it at position 120, two places on from the release button and its leaf spring at 117 and the button cover at 118. Age and handling do most of the damage here: the cap gets gripped whenever the neck is separated, and a hairline split eventually runs far enough that the piece drops away, leaving the socket open to whatever the head picks up off the floor. Once that happens the connection stops being held square, and a brush roll that cuts in and out as the neck flexes usually follows.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2961GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e the DART, and ET-1 power heads with or without the on\/off switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 120 on the DART sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCovers:\u003c\/strong\u003e the electrical socket inside the TS-neck\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2962GS button cover at 118, 1737GS release button with leaf spring at 117, 2954 swivel neck bearing at 122, 2309GS complete neck assembly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBefore starting:\u003c\/strong\u003e disconnect the machine from the outlet\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eTwo similar caps exist in the SEBO catalogue and they are not interchangeable listings, so order by the number on this page when the head in front of you is the DART build. The neck also carries a button cover and a release button within three positions of the socket cap, and all three take a beating from the same handling, which makes it worth checking them together while the joint is open. Keeping the socket enclosed is what stops a clean contact turning into an intermittent one. Genuine SEBO part held on an authorized dealer account. Ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214526177530,"sku":"2961GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/110420b00da0c9f2fc45881beeb128d6.jpg?v=1786669154"},{"product_id":"filter-indicator-complete-for-felix-series-and-dart","title":"SEBO Filter Indicator Assembly for FELIX and DART Uprights","description":"\u003cp\u003eEverything in this part arrives built. 7094ER is the SEBO filter indicator supplied complete, ready to go into a DART, a FELIX Premium or a FELIX 2 Premium without anyone having to track down the separate carrier, spring and lens and hope they match.\u003c\/p\u003e\u003cp\u003eAn indicator is the only report a machine gives on the state of its filter bag, so an unreliable one puts the owner back onto guesswork, and guesswork costs money in both directions. Bags get thrown away early because nobody trusts what the window shows, or the upright works on for weeks against a packed bag, dragging the motor harder while pickup slides away too gradually for anyone to notice. A display that has stuck in one position, hazed over, or stopped reacting when a fresh bag goes in is worth changing rather than reading around.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7094ER\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eListed for:\u003c\/strong\u003e the SEBO DART, the FELIX Premium and the FELIX 2 Premium\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied:\u003c\/strong\u003e built up as one assembly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReports:\u003c\/strong\u003e when a filter bag has reached the end of its useful life\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplace it when:\u003c\/strong\u003e the display sticks, ignores a bag change, or has clouded past reading\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eWhat the indicator reports on sits within a few inches of it and is worth putting on the same order: bags 7029AM in the eight-bag pack, with cartons 7029A1 and 7029A2 for anyone who gets through them faster; pre-motor filter 7012AM, which guards the suction motor; and 7143ER, the molded shell a bag seats into. Every one of those is listed for the same three uprights, so one service order can cover the whole bag path from inlet to motor.\u003c\/p\u003e\u003cp\u003eFitting is a straight exchange for the original assembly, no calibration and nothing to set. Genuine SEBO stock through our authorized dealership. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214528143610,"sku":"7094ER","price":14.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/f3254baa3ac9e27411c4814a408d5e1b.jpg?v=1786669096"},{"product_id":"on-off-button-lens-for-et-1-and-et-2","title":"SEBO On\/Off Button Lens for Switched ET-1 and ET-2 Power Heads","description":"\u003cp\u003eSwitched power heads carry a small moulded lens over the on\/off control. Part 2957 is that piece: the face your thumb presses and the cover that keeps carpet dust away from the switch sitting behind it.\u003c\/p\u003e\u003cp\u003eSEBO lists it at position 139 on the ET-1\/ET-2 power head diagram, where it is noted as the left hand item, at 139 on the FELIX sheet and at 136 on the DART. Yellowing, a star crack across the face, or a lens that has popped out and vanished under the sofa are the reasons this part gets ordered. Because the lens is only a cover, it is worth confirming that the switch itself still operates cleanly while the head is open: the single pole switch is 05114, the lever and leaf spring behind it are 2958ER, and SEBO sells the whole switch group built up as 2959ER if the fault turns out to be electrical rather than cosmetic.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2957\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads built with the on\/off switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 139 on the power head and FELIX sheets, 136 on the DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e button face and dust cover for the head's on\/off switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2956 brush light lens at 140, 05114 switch, 2958ER lever with leaf spring, 2959ER complete switch assembly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCheck first:\u003c\/strong\u003e confirm the switch still latches before blaming the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eUnswitched heads have no lens to lose, so check which build you have before ordering a SEBO ET-1 on\/off button lens. The brush light lens on the other side of the head is 2956, a different moulding at the next position along, and the two are easy to confuse when working from the drawing rather than the number. Genuine SEBO stock from an authorized dealer; ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214528340218,"sku":"2957","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/c4e52fcde7b157052422e5b0922e5a20.jpg?v=1786668948"},{"product_id":"lens-right-brush-light-for-et-1-and-et-2","title":"SEBO Brush Light Lens, Right Hand, for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eClear plastic keeps grit off the brush light while letting the beam through, and 2956 is the right hand lens for that duty. It seats in the power head housing over the lamp, taking the scuffs and knocks that come from working tight against baseboards, table legs and stair risers.\u003c\/p\u003e\u003cp\u003eSEBO catalogues the right hand lens at position 140 on the ET-1\/ET-2 diagram, at 140 on the FELIX sheet and at 137 on the DART, immediately alongside the on\/off button lens. Lenses cloud with age and crack on impact, and a hazed lens dims the light long before the lamp behind it gives up, which is why a machine that seems to have lost its brush light often only needs the plastic changed. Wipe out the lamp recess while the lens is off the head, and check the seat for old grit so the new lens sits flush rather than proud.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2956, right hand lens\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 140 on the power head and FELIX sheets, 137 on the DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e protects and covers the brush light in the head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2957 on\/off button lens at 139, 2684ER printed circuit board\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTip:\u003c\/strong\u003e clean the lamp recess before the new lens goes in\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eBuyers hunting a SEBO ET-2 brush light lens replacement should note the handing: this is the right hand moulding, and the switch lens on the other side of the head is a separate number entirely. Both sit within one position of each other on the same diagram, so it is easy to order the wrong one from a drawing alone. Genuine SEBO lens supplied through an authorized dealer, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214528372986,"sku":"2956","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2956_411f9f5a-468b-4659-aca8-e6fd83aa6b4e.jpg?v=1785142869"},{"product_id":"foot-pedal-with-axle-and-spring-for-et-1-et-2-and-disco-orange","title":"SEBO Foot Pedal with Axle and Spring for FELIX, ET-1, ET-2 and DISCO \u0026mdash; Orange","description":"\u003cp\u003eOrange plastic, a steel pivot pin and a return spring arrive together as one item in 2937OR. Step on the pedal and the handle unlocks from upright so the machine can be reclined for a pass under a table; lift your foot and the spring carries the pedal back, ready for the next release.\u003c\/p\u003e\u003cp\u003eSEBO draws the pedal at position 112 on the ET-1\/ET-2 power head sheet, at 112 on the DART diagram and at 112 on the FELIX diagram, with the wheel at 111 on one side of it and the complete swivel neck at 113 on the other. The DISCO floor polisher parts list carries the same pedal at position 24. Fit a new one when the handle drops loose the moment the pedal is brushed, when the pedal stays down after being pressed, or when a snapped spring leaves the lock rattling as you push. Since the pin and spring come in the pack, nothing has to be salvaged off the old assembly.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2937OR\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied as:\u003c\/strong\u003e pedal, axle and return spring together\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e orange\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched, and the DISCO floor polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 112 on the power head, DART and FELIX sheets; 24 on the DISCO list\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2306GS wheel at 111, 2307GS complete swivel neck at 113\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis is one of the most-searched SEBO FELIX pedal repairs for a reason: the pedal takes a boot every time the machine is used, and it is the part that decides whether the handle release still feels positive. German-made SEBO component from an authorized dealer, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214528733434,"sku":"2937OR","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2937OR_efad1f05-495b-44c7-8c75-1a58885a96c8.jpg?v=1785139812"},{"product_id":"handle-grip-complete-2-pcs-with-grommet-clamp-and-screws-for-felix-ice-blue-white-rose-and-dart-white","title":"SEBO Handle Grip Set for FELIX Premium, FELIX 2 Premium and DART — White, 2 Pieces with Hardware","description":"\u003cp\u003eOne grip kit, three machines. SEBO 7164WE is the complete white handle grip for the FELIX Premium, the FELIX 2 Premium and the DART, supplied as two pieces along with the grommet, the clamp and the screws that pull them together.\u003c\/p\u003e\u003cp\u003eIt turns up in both factory drawings, which is how you know it really is one kit. The DART sheet carries it at position 28, on a row written up as the complete handle supplied with its screws. The FELIX sheet carries it at position 21, written up there as the arctic white complete handle, and the two rows resolve to the same number. Position 21 is drawn three times over on that FELIX sheet, once per finish — 7164WE arctic white, 7164GSSW black and 7164DB dark blue — so it is the number, never the position, that gets the right colour into the box.\u003c\/p\u003e\u003cp\u003eA grip is the part of an upright that gets handled every day: twisted, leaned on, used to drag the machine over a threshold. It wears in ways the body never does, giving you a clamp that will not stay tight, a half that rotates on the tube, or a crack spreading out of a screw boss. Since the kit brings the grommet, clamp and screws with it, there is no separate hardware to work out. It is not the handle tube, though — the FELIX sheet draws that at position 11 as 7081ER, and a bent or split tube needs its own order. The DART sheet's other white-suffixed rows sit close by as well: handle frame 7178WE at position 31 and cable hook 7027WE at 19.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitment:\u003c\/strong\u003e SEBO FELIX Premium and FELIX 2 Premium uprights, plus the DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShade:\u003c\/strong\u003e white, printed on the FELIX sheet as arctic white — a match for the Ice Blue, the White and the Rose trims as well as for the DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIn the pack:\u003c\/strong\u003e a pair of grip halves with grommet, clamp and screws\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDrawn at:\u003c\/strong\u003e position 28 on the DART sheet, position 21 on the FELIX sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated numbers:\u003c\/strong\u003e 7164GSSW black grip kit, 7081ER handle tube\u003c\/li\u003e\n\u003cli\u003eGenuine SEBO kit, ships in 2–5 business days\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214529093882,"sku":"7164WE","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/20cf926c7dfc31320de87998b7027730.jpg?v=1786669130"},{"product_id":"tube-plug-for-dart-gray-black","title":"SEBO Tube Plug for DART — Gray Black","description":"\u003cp\u003eItem 27 on SEBO's DART exploded diagram is one of those parts nobody thinks about until it turns up missing after a service. It is the tube plug, and 7076GS is that moulding in gray black for the SEBO DART upright.\u003c\/p\u003e\u003cp\u003eIts job is to cap a tube end, keeping that run of the airway closed and the moulding finished as SEBO intended. On the DART sheet it sits in the middle of the handle and tube group, drawn just ahead of the complete handle at item 28, the sliding button at item 30 and the switch frame at item 31, with the hose at item 33 and its retaining ring at item 38 further down the same drawing. Leave that end open and it whistles under load, gathers dust down the bore and presents a raw plastic edge where a smooth face belongs.\u003c\/p\u003e\u003cp\u003ePlugs get mislaid on the bench, or they split once enough heating and cooling has worked the plastic hard. There is no good improvised substitute, since tape leaks immediately and keeps leaking as the adhesive creeps, and a wad of anything softer gets drawn into the airway. The right plug presses home into its seat in a few seconds, with no tools involved and nothing to line up. Because it is moulded to SEBO's original dimensions, it grips rather than rattles.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitment:\u003c\/strong\u003e SEBO DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7076GS, sold singly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e item 27 on SEBO's DART sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplace when:\u003c\/strong\u003e the plug is missing, split, or no longer grips its seat\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 7080ER 660 mm handle tube, 7164WE complete handle, 7050SB hose, 7018OR hose retaining ring\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eWorth ordering alongside any other DART tube or handle work rather than on its own, since it is the sort of small moulding that gets lost exactly when the machine is already apart. Stocked genuine here as an authorized SEBO dealer, with orders leaving in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214529323258,"sku":"7076GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2b30a0fb2fc5fc44c23e8baf4ba87d83.jpg?v=1786669172"},{"product_id":"handle-tube-660-mm-for-dart-and-felix-1-9802am-with-non-adjusting-handles","title":"SEBO 660 mm Handle Tube for DART — Non-Adjusting Handle","description":"\u003cp\u003e660 mm is the number that matters on this one. Part 7080ER is the fixed-length handle tube fitted to SEBO DART uprights built with the non-adjusting handle, and it replaces that tube outright rather than repairing it.\u003c\/p\u003e\u003cp\u003eThis tube is the backbone of the whole machine. It absorbs every push and pull, the leverage of a vacuum being dragged across a room by its grip, and the shock of a fall onto a hard floor. Damage is rarely obvious to look at. What you notice instead is a springy feel in use, a handle sitting a degree or two out of square, and fittings clamped along the tube that no longer line up, which pushes the load onto the joints at either end. Straightening it back seldom holds, because the tube has already yielded once in that spot.\u003c\/p\u003e\u003cp\u003eLength is the other reason to order the right part rather than a near-enough one. Nothing here telescopes, so the 660 mm dimension fixes how tall the vacuum stands in use and how long the wiring run inside it needs to be. On SEBO's DART diagram the parts that live at either end are the tube plug at item 27, part 7076GS, the complete handle at item 28, part 7164WE, the sliding button at item 30, part 7035GS, and the switch frame at item 31, part 7178WE. The cable that runs up inside a non-adjusting DART handle is part 7070.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitment:\u003c\/strong\u003e SEBO DART, non-adjusting handle build only\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength:\u003c\/strong\u003e 660 mm exactly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e non-telescoping, fixed handle tube\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7080ER\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplace when:\u003c\/strong\u003e the tube is bent, dented at a clamp point, or the handle no longer sits square to the body\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 7070 internal cable, 7076GS tube plug, 7164WE complete handle, 7178WE switch frame\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eMeasure the old tube first if the handle style on your machine is not obvious, because adjustable-handle FELIX uprights are built around a different tube altogether. Genuine SEBO DART handle tube replacement from an authorized SEBO dealer, dispatched in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214529356026,"sku":"7080ER","price":26.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/f4490792686d09e82dbbe1c0aba9b8c4.jpg?v=1786669175"},{"product_id":"exhaust-filter-clamp-for-felix-ice-blue-fun-and-dart-gray-black","title":"SEBO Exhaust Filter Clamp for FELIX Premium, FELIX 2 Premium and DART — Gray Black","description":"\u003cp\u003e7017GS is the gray black exhaust filter clamp for SEBO's FELIX uprights and the DART. It is neither the filter nor the outer cover but the frame between them, and it is the piece that decides whether the pad underneath actually does any work.\u003c\/p\u003e\u003cp\u003eEven pressure is the whole point. Air leaving the motor takes whichever route is easiest, so a pad lifted at one corner is a pad that a good share of the exhaust simply bypasses, carrying back into the room the fine dust the machine has just collected. The clamp holds the pad flat across its full face; the outer filter cover — 7091WE in white on these machines — then closes over the top. SEBO draws the exhaust filter itself separately, at position 41 of the FELIX sheet and at 24 on the DART sheet, which is a useful reminder that clamp and filter are ordered as two lines.\u003c\/p\u003e\u003cp\u003eBeing in the hand at each filter change, this clamp is the component most often broken during ordinary servicing rather than by accident. A locating tab snaps, or the frame splits across, and afterwards no amount of careful placing will make the pad sit down properly. Replacing it costs a fraction of the service it protects.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 7017GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitted to:\u003c\/strong\u003e SEBO FELIX Premium and FELIX 2 Premium uprights, plus the DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRole:\u003c\/strong\u003e keeps the exhaust filter pad flat on its seat\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSold as:\u003c\/strong\u003e clamp alone, filter ordered separately\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSame clamp in other shades for the FELIX Premium:\u003c\/strong\u003e 7017HG light gray, 7017SB silver\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFiltration on the same machines:\u003c\/strong\u003e 7012AM pre-motor filter, 7185ER anti-odor pre-motor filter, 7094ER filter indicator\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe gray black shade matches the rest of the gray black trim on these uprights, including crevice nozzle 1092GS, so a replacement does not stand out. While the compartment is open it is worth looking at the pre-motor side too, since both filters fall due on the same rough schedule. Factory SEBO clamp, authorized dealer stock, sent out in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214531813626,"sku":"7017GS","price":8.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/5f4de282931d854e41dcec091b1598f6.jpg?v=1786668966"},{"product_id":"lever-with-leaf-spring-for-et-1-and-et-2","title":"SEBO Switch Lever with Leaf Spring for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eBetween your thumb and the electrical contacts sits a lever backed by a leaf spring, and 2958ER supplies both as one piece. The spring gives the on\/off action its snap and returns the lever to rest after each press, so the control commits to on or to off rather than hovering somewhere between the two.\u003c\/p\u003e\u003cp\u003eSEBO draws the lever at position 131 on the ET-1\/ET-2 power head sheet, at 131 on the FELIX diagram and at 139 on the DART, where it sits with the single pole switch 05114 and the wire 0881 in the group that makes up the complete switch. A tired or broken spring shows up as a mushy button, a lever that stays pushed in, or a brush roll that shuts itself off when the head takes a knock against a chair leg. The lever is also supplied inside the built-up assembly 2959ER, which is the better choice when the switch body or its wiring has failed as well.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2958ER, lever and leaf spring together\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 131 on the power head and FELIX sheets, 139 on the DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e gives the on\/off control its travel, snap and return\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2959ER complete switch assembly, 05114 single pole switch, 0881 wire to the board, 2957 button lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eWhen a SEBO ET-1 switch feels dead under the thumb but the machine still runs, the lever and its spring are the parts to look at before anything electrical gets condemned, and they are far less work to change than the board behind them. Genuine SEBO parts, authorized dealer supply, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214532763898,"sku":"2958ER","price":8.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2958ER.jpg?v=1785151879"},{"product_id":"screw-sts-4-x-16-t20-single-for-x7-x8-felix-dart-softcase-300-350-and-disco","title":"SEBO Screw STS 4 x 16 (T20 Torx) for X7, X8, FELIX, DART, SOFTCASE, 300\/350 and DISCO","description":"\u003cp\u003eA T20 Torx head is what separates this fastener from the older slotted and cross-head screws in the SEBO parts book. The six-lobe recess spreads the driver load around a much larger contact area, so it takes far more torque before it rounds, and it is the head fitted on the X7 and X8, on FELIX and DART machines, on the SOFTCASE, on the 300 and 350, and on the DISCO.\u003c\/p\u003e\u003cp\u003eUse a proper T20 bit rather than a close-fitting hex key or a flat blade. A rounded recess on an STS 4 x 16 usually ends in drilling the head off, which is a far longer afternoon than replacing a screw that first felt loose. The screws worth inspecting are the ones on any machine that has been apart more than once, because a recess that has begun to round will still drive today and slip at the worst possible moment during the next service.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 1016\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO X7 and X8, FELIX, DART, SOFTCASE, 300 and 350, DISCO\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDrive:\u003c\/strong\u003e T20 Torx, six-lobe recess\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 4 mm diameter, 16 mm long\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e STS body screw\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSold:\u003c\/strong\u003e each\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSame drive, other lengths:\u003c\/strong\u003e part 1036 at 13 mm and part 1017 at 20 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eMeasure before ordering. SEBO lists 4 mm Torx screws at 13, 16 and 20 mm, all with the same head and the same T20 recess, and telling them apart by eye once they are loose in a tray is guesswork. Putting the 13 mm where the 16 mm belongs leaves the joint half clamped, which shows up later as a creak along a seam rather than as an obvious failure.\u003c\/p\u003e\u003cp\u003eReplace one when the recess has begun to open out, when the screw no longer draws the panel down however far it is turned, or when a strip-down has left you a fastener short. None of those is worth working around, because a body screw that has stopped clamping passes its share of the load to the fixings on either side of it, and those then fail in turn.\u003c\/p\u003e\u003cp\u003eAnyone searching for a SEBO X8 body screw, a FELIX Torx screw, a SEBO DART casing fastener or a genuine SEBO T20 4 x 16 replacement is after this part number. Genuine hardware from an authorized SEBO dealer, shipping in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214535287034,"sku":"1016","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0a89347fb046aa2a16f52895d4beeed6.jpg?v=1786670976"},{"product_id":"screw-sts-4-x-20-t20-single-for-felix-and-e-series-dart-and-370-comfort","title":"SEBO Screw STS 4 x 20 (T20 Torx) for FELIX, E Series, DART and 370 COMFORT","description":"\u003cp\u003eFour millimetres across and twenty long, this is the deeper of the two T20 body screws, used where a fastener passes through a thick section before it finds its boss. SEBO specifies it for the FELIX and E series, the DART and the 370 COMFORT, and supplies it individually as part 1017. The six-lobe T20 recess is the same one used across the rest of the modern SEBO range, so a single bit covers the whole strip-down.\u003c\/p\u003e\u003cp\u003eSubstituting the 16 mm version is a common shortcut and a poor one. The shorter screw engages only the top few threads, then works loose under vibration and brings the plastic with it when it finally pulls out. What starts as one loose fastener ends as a torn boss and a housing that will no longer hold anything at that point. Part 1017 puts the correct length back into the joint.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 1017\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO FELIX and E series machines, the DART and the 370 COMFORT\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDrive:\u003c\/strong\u003e T20 Torx\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 4 mm diameter, 20 mm long\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e STS body screw\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSold:\u003c\/strong\u003e each\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShorter versions:\u003c\/strong\u003e part 1016 at 16 mm and part 1036 at 13 mm, same 4 mm Torx family\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eReplace one when the recess has rounded, when the screw no longer holds torque, or when a strip-down has left you one short. Drive it home firmly but stop the moment the head seats, since over-torquing into plastic is exactly what creates the next stripped hole and the next set of loose panels around it.\u003c\/p\u003e\u003cp\u003eKeep the screws from a machine laid out in the order they were removed. Lengths are mixed within a single casing on these models, and the T20 head gives no clue as to which hole a screw came from once it has left it. Two minutes of order at the start of a job saves a good deal of trial and error at the end of one.\u003c\/p\u003e\u003cp\u003eUseful search phrasing for this one includes SEBO FELIX screw replacement, SEBO 370 COMFORT body screw, SEBO E series Torx fastener and genuine SEBO STS 4 x 20. Genuine SEBO fastener supplied by an authorized dealer, shipping in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214535352570,"sku":"1017","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/01017.jpg?v=1709348821"},{"product_id":"screw-4-x-13-tx-20-single-for-x7-x8-g4-g5-dart-softcase-370-comfort-300-350-d-e","title":"SEBO Screw 4 x 13 (Tx 20) for X7\/X8, G4\/G5, DART, SOFTCASE, 370 COMFORT, 300\/350, D and E Series","description":"\u003cp\u003eSitting below the 16 and 20 mm Torx screws, the 4 x 13 with a Tx 20 recess is the short one, and its fitment list runs right across the SEBO line: the X7 and X8, the G4 and G5, the DART, the SOFTCASE, the 370 COMFORT, the 300 and 350, and the D and E series. Part 1036 is the single-screw order for all of them.\u003c\/p\u003e\u003cp\u003eThe six-lobe Torx recess is what makes these screws survive repeated servicing, since the driver load is carried around a large contact area rather than on two thin cross flutes. That advantage disappears once the recess has begun to round. Anywhere a machine has been apart more than once the Torx screws are worth inspecting, because one that still drives today will slip at the worst possible moment during the next service, and extracting a spun screw from a plastic boss takes far longer than replacing it early.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 1036\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO X7 and X8, G4 and G5, DART, SOFTCASE, 370 COMFORT, 300 and 350, D and E series\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDrive:\u003c\/strong\u003e Tx 20, six-lobe recess\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 4 mm diameter, 13 mm long\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSold:\u003c\/strong\u003e each\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLonger screws, same drive:\u003c\/strong\u003e part 1016 at 16 mm and part 1017 at 20 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eMatch the length before ordering, as the 16 mm and 20 mm screws carry the same head and the same drive and cannot be told from this one at a glance. Use a genuine T20 bit rather than an approximate substitute, and stop driving the moment the head seats rather than leaning into the last quarter turn.\u003c\/p\u003e\u003cp\u003eBecause one screw covers so much of the range, this is the sensible one to keep spares of. A single T20 bit and a few of these cover a brush roll change, a filter housing strip and a hose cuff swap across most of the modern SEBO uprights and canisters listed above, and none of those jobs is improved by discovering halfway through that a fastener has given up.\u003c\/p\u003e\u003cp\u003eSearches that lead here include SEBO G5 body screw, SEBO X8 Torx screw, SEBO 370 COMFORT casing fastener and genuine SEBO 4 x 13 Tx 20. Genuine SEBO fastener from an authorized dealer, shipping in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214535614714,"sku":"1036","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/01036.jpg?v=1709348824"},{"product_id":"screw-amtec-3-x-12-tx-10-single-black-for-g4-g5","title":"SEBO Vacuum Motor Seal for FELIX, DART and 370 Series Uprights","description":"\u003cp\u003eAir that escapes inside the machine never does any work at the floor. The vacuum motor sits in a sealed chamber, and part 1047 is the SEBO gasket that closes the gap between motor and housing so the whole airstream is drawn through the bag and filters rather than around them.\u003c\/p\u003e\u003cp\u003eSEBO places it at position 7 on the FELIX parts sheet and position 8 on the DART sheet, identified on both as the vacuum motor seal. Seals compress, harden and take a permanent set over years of heat cycling, and a flattened one leaks quietly: suction falls away with no blockage anywhere to find, and the bag stops filling the way it used to. Fits the SEBO FELIX Premium, FELIX 2 Premium, DART, 370 COMFORT and ELECTRONIC 370.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e SEBO 1047, vacuum motor seal\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, 370 COMFORT and ELECTRONIC 370\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 7 on the FELIX sheet, 8 on the DART sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSeals:\u003c\/strong\u003e the vacuum motor to its housing\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFit it when:\u003c\/strong\u003e the motor comes out for any reason at all\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFit alongside:\u003c\/strong\u003e 05140S, the carbon brush set for the FELIX and DART suction motor\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplace when:\u003c\/strong\u003e suction has faded with no blockage to find, or the old seal is flattened and hard\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction:\u003c\/strong\u003e keeps the airstream inside the bag and filter path instead of leaking around the motor\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eRenewing the seal during a carbon or bearing job avoids a second teardown later, since an old gasket rarely re-seats as well once it has been disturbed and lifted. Set the motor down squarely on the new seal and draw its fixings up evenly rather than one at a time, so the gasket compresses across its whole face.\u003c\/p\u003e\u003cp\u003eGenuine SEBO motor seal for the FELIX, DART and 370 uprights, ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214535811322,"sku":"1047","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/f49a92da8a69d6eedadaff217ba2e3fb.jpg?v=1786668802"},{"product_id":"screw-m4-x-10-k-single-for-felix-dart-softcase-370-series-300-350-and-duo","title":"SEBO M4 x 10 Screw for FELIX, DART, SOFTCASE, 370, 300\/350 and DUO — Single","description":"\u003cp\u003eA rebuild stops dead over one missing fastener. Part 127 is the M4 x 10 k screw SEBO specifies across a wide slice of its range, sold as a single piece so a one-screw repair does not mean buying a bag of fifty. It carries a metric M4 thread 10 mm long, which is short enough to sit in a shallow seat and still be recovered and refitted at the next service.\u003c\/p\u003e\u003cp\u003eThreads flatten out after a few teardowns, and a screw that no longer holds torque lets the cover it clamps drift loose while the machine is running. The early symptoms are a panel that lifts under a fingernail at one corner and a buzz that appears only at certain motor speeds. Left alone, the loose panel loads the fasteners either side of it and the single-screw repair grows.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 127\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO FELIX and DART, the SOFTCASE, the 370 series, the 300 and 350, and the DUO\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread:\u003c\/strong\u003e M4 x 10 k\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuantity:\u003c\/strong\u003e one screw\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFit:\u003c\/strong\u003e drops into the factory hole, with no drilling or tapping\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated M4 screws:\u003c\/strong\u003e part 129 at M4 x 12 to DIN 966 and part 112 at AM4 x 10 to DIN 7985\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eHold it against the screw you removed to confirm both head style and length before ordering. Several M4 screws with different heads appear on a single SEBO machine, and while any of them will start in the hole, only the correct one seats the way the design intended. Order more than one if the repair calls for it, since these are supplied individually.\u003c\/p\u003e\u003cp\u003eThe advantage of a metric machine thread in this position is that it survives being taken apart. Where a self-tapping screw wears its own seat away a little on every removal, this one engages a thread that already exists and returns to the same tightness each time, which is why it turns up at the access points a technician opens as a matter of routine rather than once in the life of the machine.\u003c\/p\u003e\u003cp\u003eSearches that lead to this listing include SEBO FELIX M4 screw, SEBO 370 series fastener, SEBO DUO cover screw and genuine SEBO 127. Genuine SEBO hardware supplied by an authorized dealer, shipping in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214537023738,"sku":"127","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0127.jpg?v=1709348814"},{"product_id":"screw-sts-4-x-16-t20-10-pack-for-x7-x8-felix-dart-softcase-300-350-and-disco","title":"SEBO Torx T20 Screw STS 4 x 16 for X7\/X8, FELIX, DART, SOFTCASE, 300\/350 and DISCO — 10 Pack","description":"\u003cp\u003eItem 161 in the AUTOMATIC X7\/X8 parts diagram, supplied ten to a bag under 01016ER, is the 4.0 x 16 mm Torx 20 fastener SEBO carries across a broad slice of its range.\u003c\/p\u003e\u003cp\u003eBuying in tens is the practical choice for a screw this widely used, since one bag covers work on more than one machine and the same size turns up on uprights, canister-style bodies and the DISCO polisher alike. It also removes the temptation to refit a fastener whose recess has begun to round. A screw that no longer takes a clean T20 bite will strip on the next service and turn a five-minute job into a drilling exercise, and by then the head is usually sitting in a recess where a drill is awkward to hold square.\u003c\/p\u003e\u003cp\u003eNothing about the specification changes from the single-piece listing: 4.0 mm nominal diameter, 16 mm under the head, Torx 20 drive, described on SEBO's own sheet as an AMTEC screw. Keep a bag on the bench alongside the 4 x 20 mm version and the two lengths stay apart, because once they are mixed in a tray they are almost impossible to tell by eye.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO AUTOMATIC X7 Premium, AUTOMATIC X7 Pet and AUTOMATIC X8; FELIX Premium and FELIX 2 Premium; DART; CE12 Softcase; 300 Mechanical and 350 Mechanical; DISCO Floor Polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize and drive:\u003c\/strong\u003e 4.0 x 16 mm, Torx 20\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuantity:\u003c\/strong\u003e 10 screws, part 01016ER\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSingle screw:\u003c\/strong\u003e part 01016\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e item 161, AUTOMATIC X7\/X8 sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLonger version:\u003c\/strong\u003e 4 x 20 mm, part 01017ER\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe reason to keep a bag rather than order singles is simple arithmetic. Any one of the machines below carries several of these, and a rebuild that runs short of one fastener is stalled just as thoroughly as a rebuild missing a major part. Ten covers a full strip-down with spares left over.\u003c\/p\u003e\u003cp\u003eUse a genuine T20 bit, not a substitute that merely sits in the socket. The Torx recess is the reason this screw survives repeated servicing, and a rounded one gives that advantage straight back.\u003c\/p\u003e\u003cp\u003eGenuine SEBO fasteners from an authorized dealer. Ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214537548026,"sku":"01016ER","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/b14970eb666c94a3e03bf66280d4b964.jpg?v=1786668543"},{"product_id":"screw-sts-4-x-20-t20-10-pack-for-felix-and-e-series-dart-and-370-comfort","title":"SEBO Torx T20 Screw STS 4 x 20 for FELIX, DART, 370 COMFORT and AIRBELT E — 10 Pack","description":"\u003cp\u003eKeeping a bag of 01017ER on the bench means the 4 x 20 mm Torx screw is never the thing holding up a FELIX or DART rebuild.\u003c\/p\u003e\u003cp\u003eThese take the deeper fixing holes in the machines listed below, and being longer they carry more of the clamping load in an assembly. That also makes them the ones most likely to be over-torqued and stretched by an impact driver, or to have their T20 recess rounded by a bit that was already worn when the job started. Ten in a bag is enough to renew every screw in a housing instead of putting back the ones that felt a little soft, which is the difference between a machine that stays tight and one that comes back in a month.\u003c\/p\u003e\u003cp\u003eThe specification matches the single-piece listing exactly: 4 mm nominal, 20 mm under the head, Torx T20 drive, shown at item 52 on the FELIX diagram and item 21 on the DART diagram. Store them separately from the 4 x 16 mm screws in part 01016ER. The heads are indistinguishable at a glance and the only reliable way to tell them apart afterwards is to measure.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO FELIX Premium, FELIX 2 Premium, DART, 370 Comfort, and the AIRBELT E1 Kombi, AIRBELT E2 Turbo and AIRBELT E3 Premium canisters\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize and drive:\u003c\/strong\u003e 4 x 20 mm, Torx T20\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuantity:\u003c\/strong\u003e 10 screws, part 01017ER\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSingle screw:\u003c\/strong\u003e part 01017\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e FELIX item 52, DART item 21\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShorter version:\u003c\/strong\u003e 4 x 16 mm, part 01016ER\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA quick way to tell the two STS lengths apart without measuring: keep them in their bags until the moment they go back in the machine, and put the loose ones from the strip-down in a separate tray. Once the 16 mm and 20 mm screws are mixed, only a ruler will separate them again.\u003c\/p\u003e\u003cp\u003eEvery screw in the bag is genuine SEBO hardware, made to the same specification as the ones fitted on the production line.\u003c\/p\u003e\u003cp\u003eGenuine SEBO hardware. Ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214537613562,"sku":"01017ER","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/5c991463529bcf2409f15f48509e097a.jpg?v=1786668781"},{"product_id":"screw-f-3-9-x-21-din-968-10-pack-for-et-1-and-et-2","title":"SEBO Screw F 3.9 x 21 (DIN 968) for ET-1 and ET-2 Power Heads, FELIX and DART — 10 Pack","description":"\u003cp\u003eTen of the long 3.9 x 21 mm shell screws, packed as 01020ER for anyone who opens SEBO power heads on a regular basis.\u003c\/p\u003e\u003cp\u003eBrush rolls, belts and bearing blocks all live behind these fasteners, so they come out and go back far more often than most hardware on a machine, and thread wear accumulates every time. Renewing them rather than refitting the originals keeps the shell halves properly drawn together, which is what stops a head flexing and chewing through the next belt. A bag of ten is roughly what a full strip and rebuild consumes if every fixing in the housing is replaced at once.\u003c\/p\u003e\u003cp\u003eThe screws are made to DIN 968: a cross-recessed pan head with a collar beneath it, on a 3.9 mm tapping thread, 21 mm long with a flat F point. The collar puts the clamping load on a wider footprint of plastic, which matters in a housing that vibrates continuously in use. SEBO shows the same part at item 130 on the ET-1\/ET-2 and DART diagrams and item 150 on the FELIX diagram. Order the 13 mm version as 01021 and the short 9.5 mm one as 01027 if the whole set of shell fixings is being replaced together.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-1 power heads and ET-2 power heads, with or without switch; FELIX Premium and FELIX 2 Premium; DART; AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium; C3.1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 3.9 x 21 mm, DIN 968\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuantity:\u003c\/strong\u003e 10 screws, part 01020ER\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSingle screw:\u003c\/strong\u003e part 01020\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e ET-1\/ET-2 item 130, DART item 130, FELIX item 150\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther lengths for the same shell:\u003c\/strong\u003e 01021ER and 01027ER\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eStore the bag with the belts and brush spares rather than in a general fastener tin. Power head servicing goes far more quickly when the correct screws are already sorted by length, and the 21 mm, 13 mm and 9.5 mm fixings from the same shell are close enough in appearance to be worth keeping apart.\u003c\/p\u003e\u003cp\u003eAuthorized SEBO dealer stock. Ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214537646330,"sku":"01020ER","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0837c0981032117c1fdd6e485c2b3474.jpg?v=1786668783"},{"product_id":"screw-f-3-9-x-13-din-968-10-pack-for-et-1-et-2-and-softcase","title":"SEBO Screw F 3.9 x 13 (DIN 968) for ET-1\/ET-2 Power Heads and CE12 SOFTCASE — 10 Pack","description":"\u003cp\u003eTen DIN 968 screws in 3.9 x 13 mm, listed as 01021ER, covering the power head and SOFTCASE fixings in a single order.\u003c\/p\u003e\u003cp\u003eThis is the mid-length screw in the ET-1 and ET-2 shell, working alongside a longer 21 mm fastener and a short 9.5 mm one elsewhere in the same housing. Servicing a head means pulling several of each, and mixing them up on the way back together is a well-known route to a screw tip poking through a moulding or a boss split from the inside. A bag of the correct length takes the guesswork out of reassembly and leaves enough spares that nothing has to be refitted twice.\u003c\/p\u003e\u003cp\u003eThe DIN 968 form carries a collar under the pan head, giving the fixing a wider bearing surface on the plastic than the similarly sized DIN 7981 screw sold as 0102ER. The two measure the same and are not interchangeable, so it is worth keeping the bags apart on the shelf. SEBO lists this part at item 127 on the ET-1\/ET-2 and DART diagrams, item 151 on the FELIX diagram and item 163 on the SOFTCASE CE12 diagram, which is the quickest way to confirm you are ordering the right one before the machine is even open.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-1 and ET-2 power heads (switched and unswitched), FELIX Premium, FELIX 2 Premium, DART, CE12 Softcase, AIRBELT D4 Premium, AIRBELT E3 Premium, AIRBELT K3 Premium and C3.1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 3.9 x 13 mm, DIN 968\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuantity:\u003c\/strong\u003e 10 screws, part 01021ER\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSingle unit:\u003c\/strong\u003e part 01021\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther lengths for the same shell:\u003c\/strong\u003e 01020ER at 21 mm, 01027ER at 9.5 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eReassembly goes fastest when the fixings are sorted before anything is put back. Take the screws out onto a tray in the positions they came from, replace them from the bag length by length, and the shell closes on the first attempt rather than after a fastener has been found sitting in the wrong hole.\u003c\/p\u003e\u003cp\u003eGenuine SEBO fasteners from an authorized dealer. Ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214537679098,"sku":"01021ER","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/391ab7df24df2e4d8dcb871a580bf758.jpg?v=1786668753"},{"product_id":"screw-f-3-9-x-9-5-din-7981-10-pack-for-et-1-and-et-2","title":"SEBO Screw F 3.9 x 9.5 (DIN 7981) for ET-1 and ET-2 Power Heads — 10 Pack","description":"\u003cp\u003eA bag of ten short 3.9 x 9.5 mm screws, part 01027ER, for the shallow fixings in SEBO power heads and the machines that carry them.\u003c\/p\u003e\u003cp\u003eShallow-seated fasteners are the ones that shake free first, since there is less thread holding them and they sit in a high-vibration part of the machine. Finding one rattling loose in the base usually means a second has already gone missing unnoticed. Ten spares let the whole set be renewed in one pass instead of chasing them one at a time over successive services, and it saves the bench time compared with hunting for a screw mid-rebuild.\u003c\/p\u003e\u003cp\u003eThe specification is DIN 7981 with a flat F point, 3.9 mm across and 9.5 mm long, appearing at item 121 on the ET-1\/ET-2 and DART diagrams and item 152 on the FELIX diagram. Keep them separate from the longer shell screws, because the difference between 9.5 mm and 13 mm is not obvious in a parts tray and only one of the two belongs in a shallow boss. The 13 mm version is 01021ER and the 21 mm one is 01020ER, which together cover every screw length in a standard power head strip-down.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-1 power heads and ET-2 power heads, with or without switch; FELIX Premium and FELIX 2 Premium; DART; AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium; C3.1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 3.9 x 9.5 mm, DIN 7981 F point\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuantity:\u003c\/strong\u003e 10 screws, part 01027ER\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSingle screw:\u003c\/strong\u003e part 01027\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e ET-1\/ET-2 and DART item 121, FELIX item 152\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther lengths for the same shell:\u003c\/strong\u003e 01021ER and 01020ER\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA small habit worth adopting on a power head rebuild: replace every short fixing from the bag rather than mixing new screws with the ones that came out. A single tired fastener in a shell held by several is enough to let a corner lift, and the whole point of the bag is that there is no reason to let it happen.\u003c\/p\u003e\u003cp\u003eGenuine SEBO fasteners from an authorized dealer. Ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214537744634,"sku":"01027ER","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/5ff153e5e6bc3de783ebc1602876c3e8.jpg?v=1786668786"}],"url":"https:\/\/evacuumsandmore.com\/collections\/sebo-dart.oembed?page=5","provider":"Vacuums and More","version":"1.0","type":"link"}