{"title":"Sebo Et-1","description":null,"products":[{"product_id":"axle-for-swivel-neck-supports-for-et-1-and-et-2","title":"SEBO Swivel Neck Support Axle for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eEvery change of direction is absorbed by the neck joint between wand and power head. Part 2928 is the axle the swivel neck supports turn on, drawn at position 126 on SEBO's ET-1\/ET-2, DART and FELIX parts sheets, sitting one number along from the neck switch wiring that runs through the same joint.\u003c\/p\u003e\u003cp\u003eWear here is felt rather than seen. The head starts to lag behind the handle, flops at the end of a stroke, or refuses to follow into a turn at all. The right and left supports the shaft passes through are listed separately as 2311 and 2312 at positions 123 and 124, and they wear in step with it, so put a thumb on both and check for play while the joint is open. If the swivel also feels notchy rather than merely loose, the six-piece metal segment set 2950ER and the swivel neck bearing 2954 are the next two items on the same sheet worth inspecting. Disconnect the machine from the outlet before disturbing anything that carries power down into the head.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2928, supplied singly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e pivot shaft carrying the swivel neck supports\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 126 on the ET-1\/ET-2, DART and FELIX lists\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2311 support right, 2312 support left, 2954 swivel neck bearing, 2950ER metal segment set, 2307GS complete swivel neck\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTypical symptom:\u003c\/strong\u003e a head that wanders, flops or fights the line you are steering\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA SEBO ET-1 axle replacement is a bench job rather than a roadside one, but it is the quickest way to bring the steering back to where it was, and always worth doing while the neck is apart for any other reason. Genuine SEBO stock from an authorized dealer; ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214472339706,"sku":"2928","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2928.jpg?v=1709347663"},{"product_id":"bearing-block-l-h-complete-for-et-1-and-et-2-gray-black","title":"SEBO Left-Hand Bearing Block for ET-1 and ET-2 Power Heads — Gray Black","description":"\u003cp\u003ePosition 102 on SEBO's exploded views marks the left-hand brush roll bearing, and 2314GS is that component in gray black, assembled and ready to seat. The same position number applies across the ET 1 \/ ET 2 power head, DART and FELIX diagrams, so whichever sheet you are working from the reference holds.\u003c\/p\u003e\u003cp\u003eLeft and right blocks are not interchangeable and carry separate part numbers, so identify which end has gone noisy before ordering. Grinding under load, a roll that will not turn freely by hand, or visible play when you rock the roll in its seat all point at the bearing rather than the belt. The distinction matters because a slipping belt and a failed bearing can both leave a head that cleans poorly on carpet, yet the fix and the part are entirely different. With the roll out, spin each bearing on its own: a healthy one runs on smoothly for a few seconds, a failed one feels notchy or stops immediately, and a housing that has worn oval will let the whole bearing turn in its seat.\u003c\/p\u003e\u003cp\u003eBecause both ends accumulate identical hours, pairing this with the right-hand block, part 2313GS, avoids taking the head apart twice. Clear wound hair and thread from the roll shaft before reassembly, since that binding is what loads the bearings in the first place, and check the belt runs central on its pulley once everything is back together. Light gray ET-1 heads use the colour-matched block 2314HG instead of this one.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 as well as ET-2 power heads, switched or unswitched\u003c\/li\u003e\n\u003cli\u003ePart number: 2314GS\u003c\/li\u003e\n\u003cli\u003eLeft-hand brush roll bearing block, supplied complete with the bearing seated\u003c\/li\u003e\n\u003cli\u003eFinish: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 102 in the ET 1 \/ ET 2, DART and FELIX parts lists\u003c\/li\u003e\n\u003cli\u003eRelated numbers: 2313GS right-hand block, 2314HG in light gray\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO part. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214472962298,"sku":"2314GS","price":30.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2314GS.jpg?v=1785150350"},{"product_id":"bearing-block-l-h-complete-for-et-1-light-gray","title":"SEBO Left-Hand Bearing Block for Light Gray ET-1 Power Heads","description":"\u003cp\u003eSeated where the roll meets the left side of a light gray ET-1 head, 2314HG comes as one complete piece, housing and bearing together, so it drops straight into the frame with no press work and no loose parts to align.\u003c\/p\u003e\u003cp\u003eSEBO shows it at position 102 in the FELIX diagram. A tired left-hand block lets the roll sit slightly off square, which turns up as uneven bristle wear along the strip and extra noise every time the head is under load. Because the wear is gradual, most owners notice the cleaning result before they notice the sound: one side of the head keeps lifting pile properly while the other seems to skim over it, and a belt that used to sit central starts creeping toward one end of the pulley. Taking the roll out and spinning each bearing individually separates a worn block from a stretched belt in a few seconds.\u003c\/p\u003e\u003cp\u003eThe matching right-hand block is part 2313HG in the same light gray, and checking both together is the sensible approach given that the pair have run identical hours. Clear packed hair from the roll shaft while it is out, since that binding loads the bearings continuously, and confirm the roll coasts briefly after the head is switched off rather than stopping dead. The gray black version of this block is ordered as 2314GS.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2314HG\u003c\/li\u003e\n\u003cli\u003eComplete left-hand bearing block, bearing already seated in the housing\u003c\/li\u003e\n\u003cli\u003eFinish: light gray, colour-matched to light gray heads\u003c\/li\u003e\n\u003cli\u003eDiagram position: 102, FELIX parts list\u003c\/li\u003e\n\u003cli\u003eRelated numbers: 2313HG right-hand block, 2314GS in gray black\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eAuthentic SEBO stock for anyone searching a FELIX Premium brush roll bearing or an ET-1 left-hand bearing block in light gray. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214472995066,"sku":"2314HG","price":30.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/e8126626d4d9854cb13f92a5ea8bfac7.jpg?v=1786668853"},{"product_id":"bearing-block-r-h-complete-for-et-1-and-et-2-gray-black","title":"SEBO Right-Hand Bearing Block for ET-1 and ET-2 Power Heads — Gray Black","description":"\u003cp\u003eA brush roll that squeals at one end, wanders sideways, or takes a moment to come up to speed has usually lost a bearing. Part 2313GS is the right-hand half of that pair in the gray black finish, and it ships complete, so the bearing already sits in its housing and the repair is a swap rather than a press-fit rebuild on the bench.\u003c\/p\u003e\u003cp\u003eSEBO draws this piece at position 105 in the ET 1 \/ ET 2 power head diagram, and at position 105 again in the DART and FELIX diagrams. The failure has a recognisable arc. First comes a rise in running noise that tracks brush speed rather than motor speed, then the belt begins creeping toward one end of its pulley, and finally the roll develops enough play to be rocked visibly in its seat by hand. Left long enough, an out-of-square roll wears its own end cap and starts scrubbing the carpet harder on one side of the opening than the other.\u003c\/p\u003e\u003cp\u003eLook over the opposite end while the roll is out. The left-hand block, part 2314GS in the same finish, carries identical hours and tends to wear on much the same schedule, and doing both at once avoids a second strip-down. Clear wound hair from the roll shaft before reassembly, since that binding loads the bearings every time the head runs. Light gray ET-1 heads take block 2313HG instead, so order by the finish on the head in front of you. Fitment on this gray black block runs across both head widths, which is why one number covers uprights and canisters alike.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 as well as ET-2 power heads, switched or unswitched\u003c\/li\u003e\n\u003cli\u003ePart number: 2313GS\u003c\/li\u003e\n\u003cli\u003eRight-hand brush roll bearing block, supplied complete with the bearing seated\u003c\/li\u003e\n\u003cli\u003eFinish: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 105 in the ET 1 \/ ET 2, DART and FELIX parts lists\u003c\/li\u003e\n\u003cli\u003eRelated numbers: 2314GS left-hand block, 2313HG in light gray\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO part. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214473552122,"sku":"2313GS","price":18.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2313GS_74be7a83-888a-4bc1-812f-9e2c64caf642.jpg?v=1785153960"},{"product_id":"bearing-block-r-h-complete-for-et-1-light-gray","title":"SEBO Right-Hand Bearing Block for Light Gray ET-1 Power Heads","description":"\u003cp\u003eLight gray ET-1 heads use colour-matched bearing hardware, and 2313HG is the right-hand block made for them. The bearing arrives seated in its housing, so nothing has to be pressed together before the roll goes back in, and the job stays within reach of anyone comfortable taking a sole plate off.\u003c\/p\u003e\u003cp\u003eIn the FELIX parts diagram this one is drawn at position 105. Change it when the roll rattles at the right-hand end, when the belt starts tracking off centre, or when the head has picked up a low hum that rises and falls with brush speed rather than with the suction motor. A quick check settles it: lift the roll out, spin each bearing on its own, and feel for roughness or for a housing that lets the bearing turn inside its seat. A sound one runs on smoothly for several seconds after a flick.\u003c\/p\u003e\u003cp\u003eThe left-hand block for the same head is part 2314HG in matching light gray, and it is worth inspecting at the same time because both ends accumulate identical hours. The gray black version of this right-hand block is 2313GS. Clear packed hair from the roll shaft before reassembly and confirm the belt sits central once everything is back together. A roll that runs quietly and coasts for a moment after the head is switched off is seated properly; one that stops dead is still binding somewhere.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2313HG\u003c\/li\u003e\n\u003cli\u003eComplete right-hand bearing block, bearing already seated in the housing\u003c\/li\u003e\n\u003cli\u003eKeeps the brush roll square to the floor across the width of the opening\u003c\/li\u003e\n\u003cli\u003eFinish: light gray\u003c\/li\u003e\n\u003cli\u003eDiagram position: 105, FELIX parts list\u003c\/li\u003e\n\u003cli\u003eRelated numbers: 2314HG left-hand block, 2313GS in gray black\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eAuthentic SEBO stock for anyone searching a FELIX Premium brush roll bearing or an ET-1 right-hand bearing block in light gray. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214473584890,"sku":"2313HG","price":18.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/1d08c8e4dd7901fb8d792ad71316a793.jpg?v=1786668849"},{"product_id":"belt-333-3m-htdii-6-for-et-1-et-2-softcase-and-370-comfort","title":"SEBO Toothed Brush Belt 333 3M HTDII-6 for FELIX, DART, ET-1\/ET-2 and 370 COMFORT","description":"\u003cp\u003eA toothed belt cannot slip the way a smooth one does, which is why SEBO drives its brush rolls through a geared profile rather than a flat rubber loop. Part 2923 is the 333 3M HTDII-6, the same belt the SOFTCASE CE12 parts list records under the heading toothed belt 333 HTD 3M 6. It sits at position 103 on the ET-1\/ET-2, DART and FELIX sheets and at position 125 on the SOFTCASE CE12.\u003c\/p\u003e\u003cp\u003eThis is the one true consumable in the drive train. Everything else in the head is metal or moulded plastic; the belt is rubber, it is under constant tension, and it wears whether the machine is used hard or gently. A stretched belt announces itself as a brush that free-wheels, ticks under load, or gives up altogether in deep pile while the suction motor sounds entirely normal. One that has begun shedding teeth leaves black crumbs of its own inside the head, and a belt that has been run slack long enough will glaze and start to smell hot. Because the geared profile has to mesh, a tired belt also chews the pulley it runs on, so replacing it early is the cheaper decision.\u003c\/p\u003e\u003cp\u003eFull fitment is broad: the SEBO ET-1 and ET-2 power heads in both with-switch and without-switch versions, the FELIX Premium and FELIX 2 Premium, the DART, the 370 COMFORT, the CE12 SOFTCASE, the AIRBELT D4 PREMIUM, the AIRBELT E3 Premium, the AIRBELT K3 PREMIUM and the C3.1. On the 370 COMFORT it pairs with brush pulley 2919ER, and motor pulley 2319 is the driven end on the FELIX Premium, FELIX 2 Premium, DART, 370 COMFORT, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM, C3.1 and both ET heads. Access door 2909VO is the orange flap that has to come off to reach it. Keep a spare on the shelf; this is the part that strands a machine mid-room.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSEBO part 2923 — belt 333 3M HTDII-6, toothed\u003c\/li\u003e\n\u003cli\u003eFits: SEBO ET-1 and ET-2 power heads (with or without switch), FELIX Premium, FELIX 2 Premium, DART, 370 COMFORT, CE12 SOFTCASE, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1\u003c\/li\u003e\n\u003cli\u003eParts-diagram positions: 103 (ET-1\/ET-2, DART, FELIX), 125 (SOFTCASE CE12)\u003c\/li\u003e\n\u003cli\u003eType: geared drive belt, so it meshes rather than gripping by friction\u003c\/li\u003e\n\u003cli\u003eTypical symptom: brush free-wheeling, ticking under load, or stalling in deep pile\u003c\/li\u003e\n\u003cli\u003eRelated part numbers: 2919ER brush pulley, 2319 motor pulley, 2909VO access door\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine SEBO\u003c\/strong\u003e; ships in 2–5 business days\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214474535162,"sku":"2923","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0f2340c355f940c6ecec795e4f1492c2.jpg?v=1786668775"},{"product_id":"rear-bottom-plate-for-et-1-gray-black","title":"SEBO Rear Bottom Plate for ET-1 Power Heads — Gray Black","description":"\u003cp\u003eDebris left behind on the pull stroke usually points at the panel behind the roll rather than at suction. Part 2304GS is the gray black rear bottom plate used on ET-1 floor nozzles, closing off the rear of the underside and setting the height at which the trailing lip meets the floor.\u003c\/p\u003e\u003cp\u003eSEBO catalogues it at position 109 in three separate diagrams, the ET 1 \/ ET 2 power head list, the DART list and the FELIX list, each time as the complete rear bottom plate. Scraping, cracking and warping all open a gap along that edge, and a gap there bleeds air away from the roll where the airflow is meant to be doing its work. The symptoms read as a general loss of pickup on carpet, a thin line of grit left behind the head, or a nozzle that feels light and skittish instead of settling onto the floor. Hard flooring and threshold strips do most of the damage, since the plate takes the load every time the head is dragged backwards over a raised edge.\u003c\/p\u003e\u003cp\u003eTurn the head over and sight along the rear lip before ordering. A plate worn thin, missing a corner or bowed away from the shell is doing none of its job, and no amount of bag or filter changing will bring the pickup back while it stays there. The same panel covers a wide spread of machines, since the SEBO FELIX Premium, DART and C3.1 uprights and the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium canisters all run ET-1 heads. This is the gray black version; light gray heads take part 2304HG instead.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2304GS\u003c\/li\u003e\n\u003cli\u003eColour: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 109 in the ET 1 \/ ET 2, DART and FELIX parts lists\u003c\/li\u003e\n\u003cli\u003eSupplied complete\u003c\/li\u003e\n\u003cli\u003eRelated number: 2304HG in light gray\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eShips in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214476042490,"sku":"2304GS","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2304GS.jpg?v=1708929320"},{"product_id":"rear-bottom-plate-for-et-1-light-gray","title":"SEBO Rear Bottom Plate for ET-1 Power Heads — Light Gray","description":"\u003cp\u003eColour is the whole distinction here. Part 2304HG is the light gray rear bottom plate fitted to ET-1 floor nozzles, identical in duty to the gray black version and catalogued at position 109 in the FELIX diagram as the complete light gray rear plate. The gray black equivalent is part 2304GS.\u003c\/p\u003e\u003cp\u003eThis panel forms the back section of the underside. It holds the trailing lip flat to the floor and closes the air path behind the roll, so a worn or fractured panel shows up as a head that rocks slightly and picks up less on the backward stroke than the forward one. Owners often chase this fault at the bag or the filter first, because the machine still sounds strong and the airway is clear; the loss is happening under the nozzle where nobody looks. Threshold bars, stair nosings and door strips do most of the wearing, and a plate gone thin at the trailing edge will not reseal even after the shell is bolted back down.\u003c\/p\u003e\u003cp\u003eMove any seal or felt strip across from the old panel unless the replacement already carries one, and check that the plate sits flush at both ends before running the head on hard flooring. While the underside is exposed it is worth clearing packed hair from behind the roll, since that debris is what holds the plate off its seat in the first place. SEBO lists this light gray panel for the FELIX Premium, on ET-1 heads built with or without an on\/off rocker.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2304HG\u003c\/li\u003e\n\u003cli\u003eColour: light gray\u003c\/li\u003e\n\u003cli\u003eDiagram position: 109, FELIX parts list\u003c\/li\u003e\n\u003cli\u003eSupplied complete\u003c\/li\u003e\n\u003cli\u003eRelated number: 2304GS in gray black\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO part for anyone searching a FELIX Premium rear sole plate or an ET-1 rear bottom plate replacement in light gray. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214476075258,"sku":"2304HG","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2304HG_e90fe8b9-c9fa-4990-825f-ad1dde52a49b.jpg?v=1785153987"},{"product_id":"bumper-for-et-1-gray-black","title":"SEBO ET-1 Power Head Bumper — Gray Black","description":"\u003cp\u003eBaseboards, chair legs and door frames all take their turn against the front of a floor nozzle, and gray black bumper 2302GS is the trim that absorbs the punishment on ET-1 heads. It wraps the leading edge so the housing behind it never makes the contact, and it is the reason a well-kept head still looks straight after years of edge work.\u003c\/p\u003e\u003cp\u003eSEBO lists this moulding at position 101 in the DART parts diagram as the complete bumper. Trim hardens with age rather than with mileage, and the failure is predictable: it splits at a corner, works loose from its retaining channel, then lifts far enough to snag on the very furniture it exists to protect. Once that happens the marks start appearing on skirting boards and on the shell underneath. A strip that has gone rigid enough to rattle in its groove is worth changing before it takes a chip out of the housing. Replacement is a front-edge job with the head laid on its back; clear the channel of grit before pressing the new moulding home, and work from one corner across rather than pushing the middle down first.\u003c\/p\u003e\u003cp\u003eFitment runs wide on this one. The same trim serves the SEBO FELIX Premium, the DART, the C3.1 and the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium canisters, all of which use an ET-1 head, and it suits those heads whether or not they carry an on\/off rocker. Colour is the ordering decision: this is the gray black item, the light gray equivalent is part 2302HG, and the version bundled with the soft carpet front bottom plate is 2302SC.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2302GS\u003c\/li\u003e\n\u003cli\u003eColour: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 101, DART parts list\u003c\/li\u003e\n\u003cli\u003eSupplied complete\u003c\/li\u003e\n\u003cli\u003eRelated numbers: 2302HG in light gray, 2302SC with the soft carpet front bottom plate\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eShips in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214477943034,"sku":"2302GS","price":18.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2302GS_48b2cc77-88a3-4513-8cea-1ba56a2b36ba.jpg?v=1785139706"},{"product_id":"bumper-for-et-1-light-gray","title":"SEBO ET-1 Power Head Bumper — Light Gray","description":"\u003cp\u003eLight gray trim for the leading edge of an ET-1 floor head, part 2302HG is the cushioning strip that meets furniture and skirting before the housing does. SEBO carries it at position 101 in the FELIX parts diagram, described there as the complete light gray bumper.\u003c\/p\u003e\u003cp\u003eAge tells on this component more than mileage does. The material stiffens, loses its grip in the retaining channel and begins to lift at whichever end has taken the most knocks. A lifted strip absorbs nothing and instead catches on chair legs and door architraves, which is usually the moment an owner notices it at all. Other giveaways are a rattle from the front of the head at speed, a visible gap between trim and shell, and fresh scuff marks on painted skirting where there were none before. None of it affects how the machine cleans, but every week it stays on the head is another week of contact landing on the moulding behind it.\u003c\/p\u003e\u003cp\u003eFitting is a front-edge job with the head laid on its back. Clear the channel of grit before pressing the new strip home, because a single trapped stone will hold one end proud and start the whole cycle over again. Work the ends in first and settle the middle last. Order by finish rather than by shape: this light gray strip is listed by SEBO for the FELIX Premium, the gray black moulding for the same edge is part 2302GS, and 2302SC pairs that gray black trim with the soft carpet front bottom plate for plush flooring.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2302HG\u003c\/li\u003e\n\u003cli\u003eColour: light gray\u003c\/li\u003e\n\u003cli\u003eDiagram position: 101, FELIX parts list\u003c\/li\u003e\n\u003cli\u003eSupplied as a complete strip\u003c\/li\u003e\n\u003cli\u003eRelated numbers: 2302GS in gray black, 2302SC with the soft carpet front bottom plate\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO trim, the part to search for as a FELIX Premium bumper or an ET-1 light gray bumper replacement. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214477975802,"sku":"2302HG","price":18.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/f522e960456f6c6a0ecf641b69019399.jpg?v=1786668815"},{"product_id":"bumper-with-soft-carpet-front-bottom-plate-for-et-1-gray-black","title":"SEBO ET-1 Bumper with Soft Carpet Front Bottom Plate — Gray Black","description":"\u003cp\u003eTwo components in a single order: SKU 2302SC pairs the gray black ET-1 bumper with the soft carpet front bottom plate, the front sole piece SEBO supplies for soft, deep-pile flooring. Ordering them together keeps the leading edge of the head matched above and below rather than mixing a new strip against a scarred plate.\u003c\/p\u003e\u003cp\u003eThe two parts do separate jobs on the same edge. Below the line, the front plate governs how the nozzle enters the pile, and the soft carpet version is shaped to stop the head burying itself and gripping on plush flooring where a standard plate would seal down and make the machine heavy to push. Above the line, the bumper takes the impacts from furniture and skirting so the housing never has to. Damage to either is worth addressing as a pair, because both sit on the same leading edge and both shape how the head behaves at the start of every stroke.\u003c\/p\u003e\u003cp\u003eAnyone who has changed flooring to a softer pile tends to want this combination rather than the standard front plate, and it is also the sensible order when a head has been dropped on its nose and both pieces are scarred. Fitment covers the SEBO FELIX Premium, the DART, the C3.1 and the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium, in each case on ET-1 heads built with or without an on\/off rocker. If the front plate is still sound, the bumper alone is part 2302GS in gray black or 2302HG in light gray.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2302SC\u003c\/li\u003e\n\u003cli\u003ePack contents: the bumper plus the soft carpet front bottom plate\u003c\/li\u003e\n\u003cli\u003eColour: gray black\u003c\/li\u003e\n\u003cli\u003eRelated numbers: 2302GS bumper only, 2302HG light gray bumper\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO parts. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214478041338,"sku":"2302SC","price":30.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2302SC_7a9958c8-823c-4dd6-8ee8-9a30ebe0f469.jpg?v=1785137376"},{"product_id":"pile-adjustment-knob-for-et-1-and-et-2-gray-black","title":"SEBO Pile Adjustment Knob for ET-1 and ET-2 Power Heads \u0026mdash; Gray Black","description":"\u003cp\u003eCarpet height on an ET-1 or ET-2 power head is chosen with a single control, and 2931GS is it in gray black. SEBO shows the knob at position 110 on the ET-1\/ET-2 sheet, where the DART list files the same position under pile adjustment button. Turning it steps the brush roll up or down so the bristles meet plush, medium or low carpet at a sensible depth instead of skating over the fibers or stalling in them.\u003c\/p\u003e\u003cp\u003eKnobs catch on furniture legs and split at the hub long before the mechanism underneath gives out. A cracked hub turns without driving the shaft below it, which strands the head on whatever setting it was last left on, and a knob that has gone missing altogether leaves nothing to grip. Fitting a new one restores indexed selection without opening the rest of the adjustment group. If the detents themselves feel mushy rather than the knob feeling loose, look past this part to the spring at 106, part 2929, and to the complete pile adjustment assembly at 107, sold as 2316GS in gray black.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2931GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e gray black, matching the darker head trim\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 110 on the ET-1\/ET-2 sheet, and 110 on the DART list as the pile adjustment button\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther finishes:\u003c\/strong\u003e 2931HG in light gray, 2931SB in silver\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2316GS adjustment assembly, 2929 spring\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eOrder by finish rather than by feel: gray black, light gray and silver knobs share the same fitting but look plainly different on the head. Genuine SEBO part from an authorized dealer, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214480597242,"sku":"2931GS","price":8.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0733ea0293158c3f0fa21738f6b746bf.jpg?v=1786668905"},{"product_id":"pile-adjustment-knob-for-et-1-light-gray","title":"SEBO Pile Adjustment Knob for FELIX Premium and ET-1 Power Heads \u0026mdash; Light Gray","description":"\u003cp\u003ePale FELIX Premium and ET-1 housings take the light gray version of the height control, and that is 2931HG. Turning it raises or lowers the brush roll so the bristles meet plush, medium or low pile at the right depth, rather than skimming over the fibers or bogging down in them. SEBO places it at position 110 in the FELIX exploded diagram, listed there as the light gray pile adjustment button.\u003c\/p\u003e\u003cp\u003eOrder one when the detents feel mushy, when the knob spins without changing anything underneath, or when the plastic collar has split and the setting drifts on its own partway across a room. Because the knob is the only part of the group you touch, it takes all the knocks from furniture legs and stair nosings and usually fails long before the mechanism it drives. If a new knob does not restore firm, stepped selection, the fault is deeper in the group: the spring at position 106 is part 2929, and the complete pile adjustment assembly at 107 is 2316HG in light gray.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2931HG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e light gray\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e FELIX Premium, and ET-1 power heads with or without the on\/off switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 110 on the FELIX parts schematic\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e manual brush roll height selection for carpet pile\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther finishes:\u003c\/strong\u003e 2931SB in silver, 2931GS in gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2316HG adjustment assembly, 2929 spring\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA SEBO FELIX Premium height knob replacement takes minutes and needs no tools beyond what is already in the drawer, so it is the sensible first move when carpet height stops holding. The FELIX list carries both the light gray and the silver knob under position 110, which is why the part number on the old moulding, rather than the drawing, is the surest guide to what to order. Genuine SEBO production part, sold by an authorized dealer and shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214480695546,"sku":"2931HG","price":8.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/d0011783c3b8b9681c62c6251cff111d.jpg?v=1786668908"},{"product_id":"pile-adjustment-knob-for-et-1-and-et-2-silver","title":"SEBO Pile Adjustment Knob in Silver for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eSilver is the third finish SEBO offers for the height control on its power heads, and 2931SB is that knob. It is the round dial on the head that steps the brush roll up or down to suit the floor underneath: low for flat commercial loop, high for deep pile, so the brush works the fibers instead of stalling against them.\u003c\/p\u003e\u003cp\u003eThe diagrams place the silver knob at position 110 for ET-1 and ET-2 power heads, and again at position 110 on the FELIX sheet. Worn detents are the usual reason one gets ordered. The knob turns too freely, the chosen height no longer holds, and brush contact changes by itself halfway through a room. A split hub is the other common failure, and it shows up as a control that spins without moving anything. Should a new knob fail to cure it, the spring behind the mechanism is 2929 at position 106 and the complete adjustment assembly is 2316GS at 107.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2931SB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e silver\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 110 on the power head sheet and on the FELIX sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction:\u003c\/strong\u003e sets brush roll height by carpet pile depth\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther finishes:\u003c\/strong\u003e 2931HG in light gray, 2931GS in gray black\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eMachines left the factory with different trim, so match the finish already on the head rather than assuming: silver, light gray and gray black knobs interchange mechanically but look nothing alike in place. All three share the same diagram position, which means the drawing alone will not tell them apart and the part number has to do the work. Supplied as factory SEBO stock through an authorized dealer account, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214480892154,"sku":"2931SB","price":8.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/479e9b47e3f9212791c63bcf5b2d2111.jpg?v=1786668910"},{"product_id":"wiring-for-swivel-neck-for-et-1-et-2-and-disco","title":"SEBO Swivel Neck Wiring for ET-1, ET-2 and DISCO Power Heads","description":"\u003cp\u003eOf all the wiring inside a power head, the run through the swivel neck is the one that actually moves. It twists and flexes with every turn of the head and every change of direction, and part 0876ER is the pre-made loom SEBO supplies for exactly that section.\u003c\/p\u003e\u003cp\u003eFlex fatigue is gradual and then sudden. Strands break one at a time inside insulation that still looks perfect, so the brush roll starts cutting out at a particular angle of the handle, comes back when the head is straightened, and eventually stops for good. Fits the ET-1 and ET-2 power heads in both switched and unswitched builds, the DISCO Floor Polisher, and the machines these heads are supplied on: FELIX Premium, FELIX 2 Premium, DART, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and the C3.1.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e SEBO 0876ER, swivel neck wiring\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 114 on the SEBO ET 1 \/ ET 2, DART and FELIX sheets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTypical fault:\u003c\/strong\u003e the roller drops out as the head is steered, then returns when it is straightened\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied:\u003c\/strong\u003e made up to length with its terminations already fitted\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated power head wiring:\u003c\/strong\u003e 0880 for the safety switch with its lead, 0881 for the board-to-switch harness\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMachines these heads ship on:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eWork the new loom through the neck's full range of movement before the housing goes back together, so nothing is trapped, stretched or pinched at the extremes of travel. Repeating the original routing matters more here than anywhere else in the machine, because this is the one length of wire that will be bent several thousand times a year.\u003c\/p\u003e\u003cp\u003eGenuine SEBO swivel neck wiring for ET-1 and ET-2 power heads, ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214487118074,"sku":"0876ER","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0876ER.jpg?v=1785156314"},{"product_id":"wiring-from-pcb-to-on-off-switch-for-et-1-and-et-2","title":"SEBO On\/Off Switch Wiring Harness for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eShort looms take the worst of the vibration, and the run from the on\/off switch back to the board inside an ET power head is one of the shortest on the machine. Part 881 replaces that harness complete on an ET-1 or ET-2 head.\u003c\/p\u003e \u003cp\u003eA conductor fatigued at its crimp gives a switch that works when it feels like it: the head starts, dies as soon as the wand is flexed, then behaves perfectly on the bench a minute later. Because the fault follows movement rather than temperature or run time, it is one of the more frustrating ones to chase, and it is often mistaken for a failing switch or a tired brush motor. Renewing the loom brings back a positive, repeatable switch action, and it is worth looking closely at the switch contacts themselves while the wiring is out of the housing, since the two components fail from the same cause and at roughly the same age.\u003c\/p\u003e \u003cul\u003e \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 881\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eMachines:\u003c\/strong\u003e SEBO ET-1 and ET-2 power heads\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eFunction:\u003c\/strong\u003e factory loom joining the on\/off switch to the board\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003ePoints to it:\u003c\/strong\u003e switching that cuts in and out, a head that responds to being wiggled, a control that needs pressure held on it\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eInstall:\u003c\/strong\u003e match the connector orientation to the harness you remove\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eRelated:\u003c\/strong\u003e part 880, the micro safety switch with wiring for the same heads\u003c\/li\u003e \u003c\/ul\u003e \u003cp\u003eSymptoms separate this part from the interlock switch cleanly enough. Intermittent running, a head that answers to being wiggled, and switching that works one minute and not the next all sit with the harness. A head that stays completely silent from the moment it is connected sits with the micro safety switch, part 880, instead. Matching the symptom to the part first saves ordering both.\u003c\/p\u003e\u003cp\u003eUnplug the vacuum before opening the head, and route the new harness along the original path so it is not trapped when the housing closes. Searches for a SEBO ET-1 switch harness, an ET-2 on off wiring loom or a genuine SEBO power head wiring repair part land on 881. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214487249146,"sku":"881","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0881.jpg?v=1709349133"},{"product_id":"power-head-cover-for-et-1-without-on-off-switch-for-9260am-white","title":"SEBO White Power Head Cover for ET-1 Power Heads Without Switch","description":"\u003cp\u003eWhite covers belong to white machines, and on this part the colour is as much a fitment question as the mounting is. Part 20335WEET is the white top shell for the SEBO ET-1 power head in the version built with no on\/off switch, the head originally supplied on machine 9260AM. SEBO lists it at position 132 on its ET 1, ET 2 Power Heads diagram.\u003c\/p\u003e\u003cp\u003eTwo things decide whether this is the right number. The first is the switch. This shell has no rocker aperture in its top face, so a head carrying a switch up there takes the switched version instead — look at the head, not the machine, because the same canister was sold with both arrangements over the years. The second is the shade. The ET-1 cover is produced across a wide colour range, and only the white one will sit right on a white machine.\u003c\/p\u003e\u003cp\u003eThe cover is the visible upper half of the nozzle. It encloses the drive and brush assembly, keeps grit out of the belt path, and holds the shape the rest of the head is built to, so a split corner is an exposure problem as well as a cosmetic one. Replacing the shell alone leaves everything mechanical untouched, which makes it a far smaller job than fitting a complete power head to a machine that is otherwise working properly.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003ePart number: 20335WEET, SEBO ET-1 power head cover\u003c\/li\u003e\n\u003cli\u003eColour: white\u003c\/li\u003e\n\u003cli\u003eConfiguration: without on\/off switch, no rocker aperture in the top face\u003c\/li\u003e\n\u003cli\u003eDiagram position: 132 on the SEBO ET 1, ET 2 Power Heads sheet\u003c\/li\u003e\n\u003cli\u003eFits: SEBO ET-1 Power Heads built without a switch, as used on the AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003eOther shades in this cover family: black 20337SWET, red 20337DRET, graphite 20337GSET, pastel blue 20337CIET, pastel mint 20337CMET, pastel pink 20337CZET\u003c\/li\u003e\n\u003cli\u003eGenuine SEBO part; ships in 2–5 business days\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214501306618,"sku":"20335WEET","price":30.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/8deba25920f50ebcfba973250653d87e.jpg?v=1786670149"},{"product_id":"power-head-cover-for-et-1-without-on-off-switch-for-9296am-red","title":"SEBO Red Power Head Cover for ET-1 Power Heads Without Switch","description":"\u003cp\u003eRed is the shade most often chased down after an argument with a doorframe, and part 20337DRET is it: the red top cover for SEBO's ET-1 power head, in the version supplied without an on\/off switch. It is the cover originally fitted to machine 9296AM, and SEBO draws it at position 132 on the ET 1, ET 2 Power Heads diagram.\u003c\/p\u003e\u003cp\u003eThis shell is the visible upper half of the power head. It encloses the drive and brush assembly and gives the head its shape, so a split or a missing corner is both an appearance problem and an exposure problem — once the moulding is open, hair and grit reach the belt path directly, and the fixings either side of the break no longer pull the head up tight. Damage of this kind tends to arrive all at once, from a knock or a fall down a flight of stairs, rather than creeping up over years.\u003c\/p\u003e\u003cp\u003eFitting the correct switchless red cover restores the head without disturbing anything mechanical underneath it. Check the top face of the old shell before ordering: if there is a rocker opening in it, the head takes the switched version and this is not the right number. On colour, red is unmistakable against the pastels but should still be matched to the machine, and the rest of the range is listed below by part number.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003ePart number: 20337DRET, SEBO ET-1 power head cover\u003c\/li\u003e\n\u003cli\u003eColour: red\u003c\/li\u003e\n\u003cli\u003eConfiguration: without on\/off switch\u003c\/li\u003e\n\u003cli\u003eDiagram position: 132 on the SEBO ET 1, ET 2 Power Heads sheet\u003c\/li\u003e\n\u003cli\u003eFits: SEBO ET-1 Power Heads built without a switch, as used on the AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003eOther finishes in the same family: white 20335WEET, black 20337SWET, graphite 20337GSET, pastel blue 20337CIET, pastel mint 20337CMET, pastel pink 20337CZET\u003c\/li\u003e\n\u003cli\u003eGenuine SEBO part; ships in 2–5 business days\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214501339386,"sku":"20337DRET","price":30.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/59489a6ef266c0d4578b2cde78dbbf05.jpg?v=1786670291"},{"product_id":"power-head-cover-for-et-1-without-on-off-switch-for-9988am-graphite","title":"SEBO Graphite Power Head Cover for ET-1 Power Heads Without Switch","description":"\u003cp\u003eGraphite darkens the head without going all the way to black, and it is the finish SEBO supplied on machine 9988AM. Part 20337GSET is the graphite upper shell of an ET-1 power head built without an on\/off switch, shown at position 132 on the SEBO ET 1, ET 2 Power Heads diagram. It fits SEBO ET-1 Power Heads in the switchless build, including those supplied on the AIRBELT E3 Premium.\u003c\/p\u003e\u003cp\u003eOrder on two points: the switch and the shade. A plain top with no rocker opening takes this cover, while a head with a switch built into the shell needs a different part number entirely, so the check to make is on the nozzle itself rather than on the machine it plugs into. On shade, graphite is distinct from the gray black used elsewhere in the SEBO range and from plain black, and the difference is far easier to see in daylight against the machine than on a screen. Where there is any doubt, hold the old cover next to an undamaged moulding on the same head.\u003c\/p\u003e\u003cp\u003eThe shell carries no working parts of its own. It closes the top of the nozzle, keeps the drive and brush assembly enclosed, and holds the shape the head is assembled to, which is why a cracked one is worth dealing with before the split runs any further. A cover that has lost a corner also stops the surrounding screws from clamping properly, and the head begins to flex under load. Fitting a new cover disturbs nothing beneath it — the belt, roller and bearing blocks all stay in place.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003ePart number: 20337GSET, genuine SEBO ET-1 power head cover\u003c\/li\u003e\n\u003cli\u003eColour: graphite, as supplied on machine 9988AM\u003c\/li\u003e\n\u003cli\u003eConfiguration: without on\/off switch, solid top\u003c\/li\u003e\n\u003cli\u003eDiagram position: 132 on the SEBO ET 1, ET 2 Power Heads sheet\u003c\/li\u003e\n\u003cli\u003eFits: SEBO ET-1 Power Heads built without a switch, including heads supplied on the AIRBELT E3 Premium\u003c\/li\u003e\n\u003cli\u003eOther finishes in the same family: white 20335WEET, black 20337SWET, red 20337DRET, pastel blue 20337CIET, pastel mint 20337CMET, pastel pink 20337CZET\u003c\/li\u003e\n\u003cli\u003eParts underneath the shell: belt 2923, 12\" brush roller 5010AM, soft-bristle roller 5010GE, bearing blocks 2313GS and 2314GS, motor pulley 2319\u003c\/li\u003e\n\u003cli\u003eConsumables for the E3: Filter Bag Box E 8300AM, Filter Set E 8322AM, Service Box E 8334AM\u003c\/li\u003e\n\u003cli\u003eUpper cover only, supplied singly; ships in 2–5 business days\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214501404922,"sku":"20337GSET","price":30.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/7aeb2a68ce500323149d18abcacf722f.jpg?v=1786670294"},{"product_id":"power-head-cover-for-et-1-without-on-off-switch-for-9261am-black","title":"SEBO ET-1 Power Head Cover — Black, Switchless Version","description":"\u003cp\u003eCracked plastic across the top of an ET-1 nozzle leaves the belt and gear drive open to grit. Part 20337SWET is the black upper shell moulded for ET-1 nozzles that were built with no rocker switch, so its top face is solid and carries no switch aperture anywhere on it.\u003c\/p\u003e\u003cp\u003eSEBO catalogues it at position 132 of the ET 1, ET 2 Power Heads exploded view, listed there as the black ET-1 cover. Colour and switch layout both have to match before ordering, because the switched shell is a separate number and will not sit correctly on a switchless head. The reverse is equally true: fitting a solid cover to a head whose switch is mounted in the shell leaves no way to operate it.\u003c\/p\u003e\u003cp\u003eDamage to a cover of this kind is nearly always impact damage, which is worth knowing because it means the mechanism underneath is usually sound. A head that still drives its roll properly and simply looks broken needs a shell, not a replacement nozzle. The moulding lifts off and the new one goes on without touching the belt, the roll or the bearings, so this is a repair that suits a home owner as much as a workshop.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003ePart number: 20337SWET, SEBO ET-1 power head cover\u003c\/li\u003e\n\u003cli\u003eColour: black\u003c\/li\u003e\n\u003cli\u003eConfiguration: without on\/off switch, solid top face\u003c\/li\u003e\n\u003cli\u003eDiagram position: 132 on the SEBO ET 1, ET 2 Power Heads parts list\u003c\/li\u003e\n\u003cli\u003eFits: SEBO ET-1 Power Heads supplied with no on\/off rocker, as used on the AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003eOther finishes in the same family: white 20335WEET, red 20337DRET, graphite 20337GSET, pastel blue 20337CIET, pastel mint 20337CMET, pastel pink 20337CZET\u003c\/li\u003e\n\u003cli\u003eGenuine SEBO moulding, sold singly; ships in 2–5 business days\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214501535994,"sku":"20337SWET","price":30.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/f723f79f4f0f85b8978651475341ab5f.jpg?v=1786670154"},{"product_id":"power-head-cover-for-et-1-red","title":"SEBO ET-1 Power Head Cover — Red","description":"\u003cp\u003eRed ET-1 heads take this upper shell, ordered as 2326DR. It is the moulded lid that closes over the belt, pulley and wiring run inside the nozzle, and it is what gives the head its finished colour.\u003c\/p\u003e\u003cp\u003eCovers tend to fail mechanically long before anything underneath them does. A locating tab snaps and the shell stops sitting flush, a screw boss splits so the fastener no longer pulls it down, or an edge scuffs through after enough contact with baseboards. None of that stops the head cleaning straight away, but a cover that no longer closes properly lets hair and grit reach the drive components it was there to keep clean, and a loose shell rattles at speed. The other common reason to order one is cosmetic, on a machine that works perfectly but has taken a knock somewhere visible.\u003c\/p\u003e\u003cp\u003eFitment covers ET-1 power heads with or without the on\/off rocker, and SEBO also lists this cover against the AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1. Colour is the ordering decision, so match the shade against your own head before buying rather than relying on a photograph; the graphite gray black shell for the same head is part 2326GSET. Check that every locating tab engages before running the screws down, because forcing a cover that is not seated is what breaks the next one. With the shell off it is worth clearing hair from around the pulley and checking the belt, since neither will be this accessible again until the cover comes off a second time.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits SEBO ET-1 power heads, with or without the on\/off rocker\u003c\/li\u003e\n\u003cli\u003eAlso listed by SEBO for the AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1\u003c\/li\u003e\n\u003cli\u003ePart number: 2326DR\u003c\/li\u003e\n\u003cli\u003eColour: red\u003c\/li\u003e\n\u003cli\u003eUpper cover with no printed model name\u003c\/li\u003e\n\u003cli\u003eEncloses the belt, pulley and internal wiring run\u003c\/li\u003e\n\u003cli\u003eSupplied as the upper shell alone\u003c\/li\u003e\n\u003cli\u003eRelated number: 2326GSET in graphite gray black\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO part. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214501601530,"sku":"2326DR","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/615a6b1c4352dec68e7422e95e280bdd.jpg?v=1786670296"},{"product_id":"power-head-cover-for-et-1-graphite-gray-black","title":"SEBO ET-1 Power Head Cover — Graphite Gray Black","description":"\u003cp\u003eGraphite gray black is the finish on this ET-1 shell, ordered as 2326GSET. SEBO draws the cover at position 135 in the ET 1 \/ ET 2 power head diagram, which is the fastest way to confirm you are looking at the right piece before committing to an order.\u003c\/p\u003e\u003cp\u003eThe shell does two jobs at once. It keeps dust and hair away from the drive components sitting under it, and it holds the clip points and screw locations in line so the head closes flat against the chassis. A cracked one manages neither, and the consequences show up gradually: debris working its way onto the belt and pulley, a rattle from the top of the head when it is pushed at speed, and a gap along one edge that grows every time the cover is taken off and refitted. Snapped locating tabs are the usual failure, followed by split screw bosses and scuffed edges on machines that spend their lives against skirting.\u003c\/p\u003e\u003cp\u003eFitting is straightforward with the head off the wand. Seat every tab before running the screws down, because forcing a shell that is not fully engaged is what cracks the next one, and inspect the belt and pulley while the interior is open. This cover is listed for ET-1 power heads switched or unswitched, and SEBO also carries it against the AIRBELT E3 Premium. The red version of the same shell is part 2326DR, so the ordering decision comes down to the finish already on your machine. Both are the upper shell alone, supplied without internals.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits SEBO ET-1 power heads, switched or unswitched\u003c\/li\u003e\n\u003cli\u003eAlso listed by SEBO for the AIRBELT E3 Premium\u003c\/li\u003e\n\u003cli\u003ePart number: 2326GSET\u003c\/li\u003e\n\u003cli\u003eColour: graphite gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 135, ET 1 \/ ET 2 power head parts list\u003c\/li\u003e\n\u003cli\u003eUpper shell enclosing the belt, pulley and wiring\u003c\/li\u003e\n\u003cli\u003eHolds the clip points and screw locations that let the head close flat\u003c\/li\u003e\n\u003cli\u003eRelated number: 2326DR in red\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eAuthentic SEBO stock. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214501667066,"sku":"2326GSET","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/7aeb2a68ce500323149d18abcacf722f_36d151a5-c34f-4503-9776-9c469fd3be1a.jpg?v=1786670299"},{"product_id":"power-head-cover-for-et-1-black","title":"SEBO ET-1 Power Head Cover - Black","description":"\u003cp\u003eA snapped locating tab, a split running out from a screw hole, or a top that no longer sits flush are the usual reasons to order 2326SWET, the black upper shell of the SEBO ET-1 power head. It is supplied plain, with no model name printed across the face, which is exactly what separates it from the printed black shell in the same family.\u003c\/p\u003e\u003cp\u003eThe cover is the molded top of the nozzle. It clips and screws down over the drive side of the head, holds the housing square, and keeps carpet fibre and grit out of the belt and pulley underneath. SEBO draws it at position 135 on the sheet titled ET 1, ET 2 Power Heads, which is the name of a diagram rather than a fitment list, so order against the number rather than the sheet. A crack that starts at a mounting boss keeps opening under vibration until the head no longer closes flat, and from that point dust works its way onto the belt. Swapping the shell takes minutes with the head already apart, and it is the natural moment to look over the belt and the state of the bristle strip while access is easy.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2326SWET, sold singly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e black, plain molding with no print applied\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-1 power heads, both the switched and the unswitched builds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed by SEBO for:\u003c\/strong\u003e AIRBELT D4 PREMIUM and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 135, SEBO ET 1 \/ ET 2 power head sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied as:\u003c\/strong\u003e the shell alone, with no internal components\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther ET-1 shells:\u003c\/strong\u003e 2326WEET in white, 2326VOET in orange, 2360SWSE, the printed black shell, which is a separate number again\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eIf you are hunting a genuine SEBO ET-1 power head cover, or a black nozzle top for an AIRBELT D4 PREMIUM or AIRBELT K3 PREMIUM, this is the number to quote. SEBO catalogs its small hardware separately as well, so a chewed fixing need not hold up the repair: screw 3.9 x 16 is listed as 0103 singly and 0103ER in a ten pack, with locking washers as 0141 and 0141ER. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214501699834,"sku":"2326SWET","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/03fd84758e199f5452bcde0db513974e.jpg?v=1786670160"},{"product_id":"power-head-cover-for-et-1-orange","title":"SEBO ET-1 Power Head Cover - Orange","description":"\u003cp\u003eOrange is the giveaway on a FELIX, and 2326VOET is the orange ET-1 upper shell in its plain form, molded without any name printed across the top. Nothing electrical comes with it. This is the cover itself, the piece that clips and screws down over the drive side of the nozzle and gives the head its finished face.\u003c\/p\u003e\u003cp\u003eGetting the shade right matters as much as getting the model right, because SEBO issues a separate number for every finish and every print in this family. The plain orange cover is the one on this page; the orange shell wearing the FELIX wordmark is ordered as 2333VOSE, while 2326SWET and 2326WEET cover plain black and plain white. SEBO places the ET-1 cover at position 135 on its ET 1 \/ ET 2 power head diagram.\u003c\/p\u003e\u003cp\u003eReach for a new shell when a locating tab has broken off, when a crack has opened around a screw boss, or when the top will not pull down flush on the base any more. A head that cannot close square lets grit past the joint and onto the belt, and the crack itself grows every time the machine is worked.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2326VOET\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e orange, unprinted\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-1 power heads, switched or unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed by SEBO for:\u003c\/strong\u003e FELIX Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 135 on the ET 1 \/ ET 2 sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack:\u003c\/strong\u003e one cover, no fixings or internals included\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated numbers:\u003c\/strong\u003e 2333VOSE orange with FELIX print, 2326SWET black, 2326WEET white\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eSearches for an orange SEBO ET-1 power head cover, or a FELIX Premium nozzle top, land on this part. Genuine SEBO stock, shipping in 2-5 business days. SEBO lists common fasteners on their own too, so if a screw came out damaged, 0104 covers screw 3.9 x 25 singly and 0104ER supplies the same in a ten pack.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214501732602,"sku":"2326VOET","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/aa362d66588a140dca9ccae77349ed0a.jpg?v=1786668873"},{"product_id":"power-head-cover-for-et-1-white","title":"SEBO ET-1 Power Head Cover - White","description":"\u003cp\u003eOf all the white ET-1 shells SEBO lists, 2326WEET is the one with the broadest fitment, and it is the plain version, molded with no printed model name across the top. Matching a broken cover means getting the shade and the fitment right in the same order, and this number settles both for a wide spread of machines.\u003c\/p\u003e\u003cp\u003eThe shell carries the clip points and screw bosses for the whole nozzle, so it is doing structural work rather than simply looking tidy. Once one has cracked, the head stops closing square, dust starts finding its way onto the belt, and the split keeps travelling under vibration until the top no longer seats. SEBO calls the cover out at position 135 in its ET 1 \/ ET 2 power head diagram, a drawing that covers two head families on one sheet, so treat the sheet title as the name of a diagram and let the part number decide the fitment. With the head open for the swap, check the belt tension and how much bristle is left on the strip before closing everything back up, since neither is easy to reach again afterwards.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2326WEET\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e white, plain, no print applied\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-1 power heads, with or without the switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed by SEBO for:\u003c\/strong\u003e AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 135, ET 1 \/ ET 2 power head sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied as:\u003c\/strong\u003e the bare shell, sold individually\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNot included:\u003c\/strong\u003e belt, brush roller, switch or fixings\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrinted white alternatives:\u003c\/strong\u003e 2331WEAM and 2331WESE, each carrying a printed model name on the face\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther plain shells:\u003c\/strong\u003e 2326SWET in black, 2326VOET in orange\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eIf the machine in front of you is an AIRBELT E3 Premium or a C3.1 and the white nozzle top has split, this is the SEBO ET-1 power head cover replacement to order. The printed white shells look near identical in a photograph but are different part numbers, so buy against the number rather than the picture. SEBO catalogs its small hardware separately as well, listing screw 3.9 x 16 as 0103 singly and 0103ER in a ten pack, with locking washers as 0141 and 0141ER, which is useful when the original fixings come out chewed. Genuine SEBO part; ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214501765370,"sku":"2326WEET","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/8deba25920f50ebcfba973250653d87e_f77373ec-0e91-45b4-ac85-3de882651380.jpg?v=1786670163"},{"product_id":"power-head-cover-for-et-1-with-felix-print-red","title":"SEBO ET-1 Power Head Cover with FELIX Print - Red","description":"\u003cp\u003eThe FELIX wordmark is printed straight onto this shell, and that is what separates 2330DRSE from a plain red ET-1 cover. Same molding underneath, different face. An unprinted shell will bolt on and function, but the machine will not look right afterwards, so order against the number rather than the outline.\u003c\/p\u003e\u003cp\u003eThis is the top half of the power head: the piece that closes over the belt, pulley and drive side of the nozzle and takes every knock the head collects against furniture legs and baseboards. SEBO lists it at position 135 in the FELIX parts diagram. The symptom that sends most people looking is a cracked or missing corner, a mounting tab that has broken away, or a printed surface worn through after enough years of use. Left alone, a split spreads from the fixing outward until the shell works loose, the head rattles, and grit that ought to stay outside ends up on the belt.\u003c\/p\u003e\u003cp\u003eFitting the new cover is a screwdriver job once the head is apart, and it is the sensible moment to look over the belt and the bristle strip while everything is accessible. The shell arrives bare: no belt, no roller, no switch and no fixings, so reuse the originals unless they are damaged.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2330DRSE\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor and finish:\u003c\/strong\u003e red, with the FELIX name printed on the top face\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-1 power heads, with or without the switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed by SEBO for:\u003c\/strong\u003e FELIX Premium\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 135, FELIX parts diagram\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack:\u003c\/strong\u003e single cover, no internal components\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther printed ET-1 shells:\u003c\/strong\u003e 2360SWSE in black, 2361DBSE in dark blue, 2331WESE in white, 2333VOSE in orange\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePlain shells\u003c\/strong\u003e carry their own numbers, among them 2326SWET, 2326VOET and 2326WEET\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003ePeople type this one in as a red FELIX Premium power head cover, or as a genuine SEBO ET-1 cover with FELIX print, and both describe 2330DRSE. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214501863674,"sku":"2330DRSE","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/066e541ec5984ed1133bc40c7b177129.jpg?v=1786668876"},{"product_id":"power-head-cover-for-et-1-with-dart-print-white","title":"SEBO ET-1 Power Head Cover with DART Print - Arctic White","description":"\u003cp\u003eDART machines carry a printed shell of their own, and 2331WEAM is it. SEBO gives the finish its own name in the parts book, arctic white, and prints the DART wordmark across the top face of the ET-1 power head cover.\u003c\/p\u003e\u003cp\u003ePosition 132 is where it sits in the DART diagram, which is worth noting if you are working from the sheet rather than from the number, since most of the ET-1 covers are drawn at 135 on their own diagrams. The cover itself is the molded upper half of the nozzle, screwed and clipped down over the drive side, sealing the belt and pulley away from the grit the machine is picking up an inch below. Replace it when a corner has broken out, when a fixing point has cracked and the top no longer pulls down tight, or when the printed surface has worn away and the head looks tired next to the rest of the machine. A cover that cannot seat flush lets the housing flex, and that flex ends up in the belt path.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2331WEAM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor and finish:\u003c\/strong\u003e arctic white, SEBO's own name for the shade, with the DART print applied\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e the SEBO DART, and ET-1 power heads whether switched or unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 132, DART parts diagram\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied as:\u003c\/strong\u003e the shell alone, sold singly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNot included:\u003c\/strong\u003e brush roller, belt, switch or fixings\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther white shells:\u003c\/strong\u003e 2326WEET in plain white, and 2331WESE, the other printed white version\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe print is the only thing separating this from the other white ET-1 covers in the range, and photographs rarely show it clearly, so order by number. Searches for a SEBO DART power head cover replacement, or for a genuine SEBO arctic white ET-1 cover, both point here. If a fixing is beyond reuse, SEBO lists its hardware individually too, with screw 3.9 x 16 as 0103 and 0103ER for a ten pack. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214502027514,"sku":"2331WEAM","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/740d84c7c2d64bf5a84b83450959ac06.jpg?v=1786669152"},{"product_id":"power-head-cover-for-et-1-with-felix-print-white","title":"SEBO ET-1 Power Head Cover with FELIX Print - White","description":"\u003cp\u003eTwo things set this shell apart from a plain white one: the FELIX print across the top, and the number itself, 2331WESE. Underneath, it is the same ET-1 cover closing the nozzle over its drive side, with the same clip points and the same screw bosses.\u003c\/p\u003e\u003cp\u003eCracks in a cover almost always begin at a mounting point and spread from there, so it pays to catch one early rather than wait for the shell to work loose in use. A cover that no longer sits down tight lets the head flex, and that flex passes straight into the belt path underneath, which is how a cosmetic split turns into a drive complaint. SEBO draws this part at position 135 in the FELIX diagram, and the swap is a screwdriver job once the head is open. While it is apart, the belt and the bristle strip are both worth a look, because access to either is awkward once everything is closed up again.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2331WESE\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor and finish:\u003c\/strong\u003e white, with the FELIX name printed on the face\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-1 power heads, with or without the switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed by SEBO for:\u003c\/strong\u003e FELIX Premium\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 135, FELIX parts diagram\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack:\u003c\/strong\u003e one cover, no internals supplied\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDistinct from:\u003c\/strong\u003e 2326WEET, the unprinted white shell, and 2331WEAM, the other printed white shell\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrinted shells in other colors:\u003c\/strong\u003e 2360SWSE black, 2330DRSE red, 2361DBSE dark blue, 2333VOSE orange\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA shopper looking for a white FELIX Premium power head cover, or for a genuine SEBO ET-1 cover with the FELIX print, wants this number rather than one of the plain shells. Should any of the original fixings be past reuse, SEBO lists them separately, with screw 2.9 x 13 as 0107 and 0107ER for a ten pack. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214502060282,"sku":"2331WESE","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/83152753f3478dda08b86fe24b748b09.jpg?v=1786668879"},{"product_id":"power-head-cover-for-et-1-with-felix-print-for-fun-orange","title":"SEBO ET-1 Power Head Cover with FELIX Print - Orange","description":"\u003cp\u003eOrange with the FELIX print, 2333VOSE differs from the plain orange shell in two ways: the printed name on top, and a narrower listing, because SEBO records this one only against ET-1 power heads built with the switch. That detail is easy to miss and it is the reason to identify the head before ordering.\u003c\/p\u003e\u003cp\u003eThe cover is the molded top of the nozzle, screwed and clipped down over the belt and pulley. It gives the head its color and its printed identity, and it absorbs the impacts that come with cleaning around furniture and baseboards. Reach for a new one when the original has cracked, dropped a locating tab, gone brittle at a fixing, or worn through its printed surface after enough years of service. A shell that no longer closes flat lets dust into the drive area, which is the practical argument for replacing it rather than living with it.\u003c\/p\u003e\u003cp\u003eNothing internal comes in the box. This is the shell on its own, so the belt, roller, switch and fixings all carry over from the head being repaired. If a screw is chewed, SEBO catalogs its hardware separately, listing screw 3.9 x 25 as 0104 singly and 0104ER in a ten pack.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2333VOSE\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor and finish:\u003c\/strong\u003e orange, carrying the FELIX print\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-1 power heads built with the switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed by SEBO for:\u003c\/strong\u003e FELIX Premium\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNot listed for:\u003c\/strong\u003e unswitched ET-1 heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack:\u003c\/strong\u003e single shell, no internal components\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThe plain orange shell\u003c\/strong\u003e is a separate order under 2326VOET\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther FELIX printed shells:\u003c\/strong\u003e 2360SWSE black, 2330DRSE red, 2331WESE white, 2361DBSE dark blue\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eIf the search that brought you here was an orange FELIX Premium power head cover, or a genuine SEBO ET-1 cover with FELIX print, this is the number that matches. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214502158586,"sku":"2333VOSE","price":30.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0848539d6f8722535150b49f55770c2f.jpg?v=1786668882"},{"product_id":"power-head-cover-for-et-1-with-felix-print-black","title":"SEBO ET-1 Power Head Cover with FELIX Print - Black","description":"\u003cp\u003eBlack shells carrying the FELIX print use part number 2360SWSE, which SEBO draws at position 135 in the FELIX parts diagram. The unprinted black ET-1 cover is a separate number, so match the print as well as the color when the order goes in.\u003c\/p\u003e\u003cp\u003eOnce a shell has cracked around a screw boss it keeps opening up under vibration, and the nozzle loses the flat, sealed fit it needs to work properly. From there dust reaches the belt and pulley, the head starts to rattle, and what began as a cosmetic split turns into a drive problem. A new cover puts that right and takes minutes with the head already apart. While it is open, the belt and the bristle strip are both worth a look, since neither is easy to inspect once everything is closed back up.\u003c\/p\u003e\u003cp\u003eThe part is supplied as the bare shell: no belt, no roller, no switch and no fixings, all of which carry across from the existing head. If a screw is past reuse SEBO catalogs its hardware individually, listing screw 3.9 x 16 as 0103 singly and 0103ER in a ten pack, with locking washers as 0141 and 0141ER.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2360SWSE\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor and finish:\u003c\/strong\u003e black, with the FELIX name printed on\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-1 power heads, with or without the switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed by SEBO for:\u003c\/strong\u003e FELIX Premium\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 135, FELIX parts diagram\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack:\u003c\/strong\u003e one shell, no internals included\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePlain black equivalent:\u003c\/strong\u003e 2326SWET, a different part number\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eSearches for a black FELIX Premium power head cover, or for a genuine SEBO ET-1 cover with FELIX print, both resolve to this number. The other printed ET-1 shells in the range are 2330DRSE in red, 2361DBSE in dark blue, 2331WESE in white and 2333VOSE in orange. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214502224122,"sku":"2360SWSE","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/42afb0e3e16be043781b83a2db952cec.jpg?v=1786668885"},{"product_id":"power-head-cover-for-et-1-with-felix-print-dark-blue","title":"SEBO ET-1 Power Head Cover with FELIX Print - Dark Blue","description":"\u003cp\u003eSEBO records this dark blue cover against a single machine, the FELIX Premium, and that is the whole of its listed fitment. It is ordered as 2361DBSE and arrives with the FELIX print already applied to the top face.\u003c\/p\u003e\u003cp\u003eThe shell forms the molded top of the power head, closing over the drive side of the nozzle and taking the day-to-day knocks that come with it. Position 135 in the FELIX parts diagram is the reference to check against the machine in front of you. What sends most owners looking for one is a crack running out from a screw boss, a locating tab that has broken off, or a cover gone dull and scuffed while the rest of the machine still looks presentable. A shell that no longer seats flush lets the head flex, and the flex works its way into the belt path underneath, so the sooner it is changed the less it costs.\u003c\/p\u003e\u003cp\u003eSupplied on its own, without belt, roller, switch or fixings, this is a straight exchange once the head is apart. If a screw comes out chewed, SEBO lists its hardware separately, with screw 3.9 x 16 as 0103 singly and 0103ER in a ten pack, and locking washers as 0141 and 0141ER.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2361DBSE\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor and finish:\u003c\/strong\u003e dark blue, wearing the FELIX print\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e the SEBO FELIX Premium\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 135, FELIX parts diagram\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied as:\u003c\/strong\u003e the cover alone, sold singly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNarrowest fitment\u003c\/strong\u003e of the printed ET-1 shells, so order by number rather than by eye\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eColor and print both differ from the rest of the family. The printed alternatives are 2360SWSE in black, 2330DRSE in red, 2331WESE in white and 2333VOSE in orange, and none of them is a substitute on a dark blue machine. Genuine SEBO part; ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214502289658,"sku":"2361DBSE","price":34.0,"currency_code":"USD","in_stock":true}]},{"product_id":"access-door-with-axle-and-spring-for-et-1-and-et-2-orange","title":"SEBO Access Door with Axle and Spring for ET-1 and ET-2 Power Heads \u0026mdash; Orange","description":"\u003cp\u003eET-1 and ET-2 power heads pass this hinged door on to every machine built around them, which is why one orange component covers so much of the SEBO range. Part 2909VO ships complete with its axle and spring, and SEBO puts it at position 108 on the ET-1\/ET-2, DART and FELIX parts sheets alike.\u003c\/p\u003e\u003cp\u003eThe door is what gets opened for belt and brush access, so its hinge sees more cycles than almost anything else on the head. As the spring slackens or the axle wears its bore oval, the door stops sitting flush: it hangs open a few millimetres, drags on carpet as the head is pulled back, rattles over hard floors, and eventually breaks at the pivot where the plastic has been working. Fitting the assembled part restores the pivot and the closing tension in one go, with no hardware to transfer across from a broken door and nothing to line up by hand.\u003c\/p\u003e\u003cp\u003eFull fitment runs to the SEBO ET-1 and ET-2 power heads in both the with-switch and without-switch versions, the FELIX Premium and FELIX 2 Premium, the DART, the AIRBELT D4 PREMIUM, the AIRBELT E3 Premium, the AIRBELT K3 PREMIUM and the C3.1. Behind the same door sit the parts most often replaced with it: toothed belt 2923, axle 2928, spring 2929 and orange foot pedal assembly 2937OR. Roller sizes split by head — the 12 inch 5010AM covers the ET-1 heads, FELIX Premium, DART, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1, while the ET-2 heads and the FELIX 2 Premium take the 15 inch 2838AM. Searches for a SEBO access door with its axle and spring fitted, an ET-1 belt door or a FELIX brush access door land here.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSEBO part 2909VO — hinged access door, axle and spring included\u003c\/li\u003e\n\u003cli\u003eFits: SEBO ET-1 and ET-2 power heads (with or without switch), FELIX Premium, FELIX 2 Premium, DART, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1\u003c\/li\u003e\n\u003cli\u003eColor: orange\u003c\/li\u003e\n\u003cli\u003eParts-diagram position: 108 on the ET-1\/ET-2, DART and FELIX sheets\u003c\/li\u003e\n\u003cli\u003eTypical symptom: a door that will not latch flush, drags on carpet, or has snapped at the hinge\u003c\/li\u003e\n\u003cli\u003eRelated part numbers: 2923 belt, 2928 axle, 2929 spring, 2937OR foot pedal with axle and spring\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine SEBO\u003c\/strong\u003e; ships in 2–5 business days\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214507041018,"sku":"2909VO","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2909VO_bbb0cc33-49e9-460f-8834-32029ed2e7b1.jpg?v=1785150214"},{"product_id":"chassis-for-et-1-gray-black","title":"SEBO ET-1 Power Head Chassis — Gray Black","description":"\u003cp\u003eEverything inside an ET-1 head bolts to the chassis: motor, roll bearings, wheels and the height linkage all take their alignment from it. Part 2324GS is that frame in gray black, supplied as the frame alone so the original internals move across into it.\u003c\/p\u003e\u003cp\u003eA split screw boss or a frame twisted by a hard fall puts the roll out of parallel with the floor, and no set of new bearings will correct that. The symptoms are the ones that survive every other repair: a head that still runs noisy after fresh bearing blocks, a belt that keeps tracking off despite a new pulley, uneven bristle wear across the strip, or a wheel mount that no longer holds its position. Stairs account for most of the damage, followed by heads that have been leaned on while the machine was parked upright. SEBO shows the ET-1 chassis as position 100 in the DART diagram.\u003c\/p\u003e\u003cp\u003eAllow proper time for the transfer and keep fasteners grouped by where they came from, because the same screw is not always used at every location. Inspect the bearing blocks, the belt and the pulley while the internals are out, since all three are far easier to reach with the frame stripped than they will ever be again. Fitment covers the SEBO FELIX Premium, DART and C3.1 uprights and the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium canisters. Light gray heads take chassis 2324HG.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2324GS\u003c\/li\u003e\n\u003cli\u003eColour: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 100, DART parts list\u003c\/li\u003e\n\u003cli\u003eSupplied as the bare frame; original internals transfer across\u003c\/li\u003e\n\u003cli\u003eRelated number: 2324HG in light gray\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO part. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214508777722,"sku":"2324GS","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/298c2e475930d6a048e10c3c4addee01.jpg?v=1786668867"},{"product_id":"chassis-for-et-1-light-gray","title":"SEBO ET-1 Power Head Chassis — Light Gray","description":"\u003cp\u003eRebuilding a light gray ET-1 head around a cracked frame rarely holds, which is where 2324HG comes in. It is the replacement chassis in the matching finish, carrying the bearing seats, the motor mounting and the wheel locations that keep the brush roll square to the floor.\u003c\/p\u003e\u003cp\u003eSEBO draws it at position 100 in the FELIX diagram. This is the part to reach for when a head has been dropped down a flight of stairs, when a screw boss has split so a fastener no longer pulls up tight, or when a repair that should have worked did not. Fresh bearing blocks in a twisted frame will still let the roll sit out of parallel, and a new belt on a frame with a distorted motor mount will keep tracking off no matter how carefully it is fitted. Signs to look for are hairline cracks radiating from screw locations, a wheel mount that has opened up, and a visible twist when the frame is set down on a flat surface.\u003c\/p\u003e\u003cp\u003eThe original internals transfer across into the new frame, so the work is mostly patience and a tidy bench rather than anything needing special tooling. Group the fasteners by location as they come out, check the bearing blocks and the belt while everything is accessible, and set the pile height mechanism back to a known position before closing up. The gray black version of this chassis is 2324GS, and the two differ only in finish. This is also a good moment to renew any wear part already close to the end of its life, because access to the interior of an ET-1 head is never better than with the frame stripped.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2324HG\u003c\/li\u003e\n\u003cli\u003eColour: light gray\u003c\/li\u003e\n\u003cli\u003eDiagram position: 100, FELIX parts list\u003c\/li\u003e\n\u003cli\u003eSets the alignment for the brush roll, motor and wheels\u003c\/li\u003e\n\u003cli\u003eSupplied as the bare frame; internals transfer from the old chassis\u003c\/li\u003e\n\u003cli\u003eCarries the bearing seats, motor mounting and wheel locations\u003c\/li\u003e\n\u003cli\u003eRelated number: 2324GS in gray black\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eAuthentic SEBO stock. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214509957370,"sku":"2324HG","price":34.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2324HG_3b92a50b-9b53-46b6-bc24-6986deecbb68.jpg?v=1785158122"},{"product_id":"back-cover-ts-neck-for-et-1-et-2-felix-except-white-and-disco-gray-black","title":"SEBO Back Cover for the TS-Neck \u0026mdash; FELIX, ET-1, ET-2 and DISCO, Gray Black","description":"\u003cp\u003eBehind the TS-neck joint sits a molded panel that caps the back of the head. Part 2947GS is that panel in gray black, shaped to the housing contour and drilled for the original screws, so the head goes back together without packing or shimming anything into place.\u003c\/p\u003e\u003cp\u003eSEBO's power head diagram numbers the cover 115, and the FELIX sheet uses the same number, immediately after the swivel neck wiring at 114 and just before the metal segment set at 116. Panels crack where they get gripped during a wand change, or when the head is tipped hard against a stair nose. Once broken, the opening lets dust reach the neck hardware and the joint loses some of its stiffness, so the head feels less planted underfoot. Replacing the cover is a screwdriver job with the head on the bench, and it is the right moment to look at the segments and slide inside the same joint.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2947GS, TS-neck back cover\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched, and the DISCO floor polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 115 on the power head and FELIX sheets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther finish:\u003c\/strong\u003e light gray panel 2947HG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 0876ER swivel neck wiring at 114, 2950ER segment set at 116, 2945GS slide at 119\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting tip:\u003c\/strong\u003e photograph the screw layout before the old panel comes off\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA genuine SEBO TS-neck cover keeps the dust out of the joint it protects, which is the whole reason to fit the correct moulding rather than tape over a split. Factory SEBO part supplied by an authorized dealer, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214514970874,"sku":"2947GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0ef463bbc1139d200d413b609783f585.jpg?v=1786668920"},{"product_id":"back-cover-ts-neck-for-felix-white-and-et-1-light-gray","title":"SEBO Back Cover, TS-Neck, for FELIX Premium and ET-1 Power Heads \u0026mdash; Light Gray","description":"\u003cp\u003eMatching the pale housings, this rear panel caps the back of the head where the TS-neck joins it, and carries part number 2947HG. It is the light gray version of the moulding; darker machines take 2947GS instead, so pick by the colour of the trim already on the head rather than by the shape of the part.\u003c\/p\u003e\u003cp\u003eThe FELIX schematic lists it at position 115, directly after the swivel neck wiring at 114 and before the metal segment set at 116. A cover with a corner missing is worth attending to promptly, because the gap is exactly where fine dust settles onto the neck hardware. The panel also does quiet structural work, tying the rear of the head together at the point where the neck loads it, which is why a badly cracked one can make the whole joint feel softer than it should.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2947HG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e light gray\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e FELIX Premium, and ET-1 power heads with or without the on\/off switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 115 on the FELIX parts sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e uses the original fasteners, no drilling\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther finish:\u003c\/strong\u003e 2947GS in gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 0876ER swivel neck wiring, 2950ER segment set, 2945HG light gray slide, 2951HG light gray socket cover\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eAnyone searching for a SEBO FELIX Premium back cover replacement is usually looking at a split corner or a lost panel, and both are worth fixing before grit reaches the neck. The panel comes off with the same screws that hold it, so the only real preparation is noting which fastener came from where before the old moulding is lifted away. With the back of the head open it costs nothing extra to look at the segments and slide inside the joint, since those are the parts that quietly decide how the machine steers. Genuine SEBO stock held under an authorized dealer account. Ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214515003642,"sku":"2947HG","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/772759d090fafba09f6f4cc71e583935.jpg?v=1786668922"},{"product_id":"release-button-cover-for-et-1-et-2-felix-swivel-neck-2307gs-and-disco-gray-black","title":"SEBO Release Button Cover for FELIX, ET-1, ET-2 and DISCO Swivel Necks \u0026mdash; Gray Black","description":"\u003cp\u003eEvery time the handle is reclined, a thumb lands on the neck release button and on the cap that covers it. Part 2952GS is that cap in gray black, giving the button a defined face to press and keeping the mechanism beneath it sealed away from dust.\u003c\/p\u003e\u003cp\u003eSEBO numbers the button cover 118 on the ET-1\/ET-2 power head diagram and 118 again on the FELIX sheet, immediately after the release button and its leaf spring at 117. When the cap splits or works its way loose, the release starts to feel vague: you press, nothing obvious happens, and the handle only drops on the second or third attempt. If a new cap does not restore a crisp action, the button assembly itself is the next item to check, listed in gray black as 1737GS, and the complete gray black swivel neck it all mounts into is 2307GS.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2952GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched, and the DISCO floor polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNeck reference:\u003c\/strong\u003e used on swivel neck 2307GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 118 on the power head and FELIX sheets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther finish:\u003c\/strong\u003e light gray cap 2952HG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 1737GS release button with leaf spring, 2951GS socket cover, 2945GS slide\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eSmall parts like this decide how a machine feels in the hand, and a sound cap is the difference between a handle that releases on the first press and one that has to be worked at. Order by finish rather than by shape, since the light gray cap fits the same button but sits obviously wrong against darker trim. Authorized SEBO dealer stock, packed and shipped in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214525653242,"sku":"2952GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/92dff885fa0a839dc6919563415f13e0.jpg?v=1786668936"},{"product_id":"release-button-cover-for-felix-white-and-et-1-swivel-neck-2307hg-light-gray","title":"SEBO Release Button Cover for FELIX Premium and ET-1 Swivel Necks \u0026mdash; Light Gray","description":"\u003cp\u003ePressed thousands of times over a machine's life, the release button cap eventually wears smooth or cracks across its face. 2952HG is the light gray replacement, listed by SEBO for the FELIX Premium and the ET-1 power head, and used on swivel neck 2307HG.\u003c\/p\u003e\u003cp\u003ePosition 118 on the FELIX parts diagram identifies it, sitting directly after the release button and leaf spring at 117. A cap that has broken away leaves the button proud and unprotected, so grit finds its way into the mechanism and the action grows stiff. Fitting a new one restores a defined face for the thumb and a clean stop at the end of the press. Where the button underneath has also gone soft, the light gray button and spring assembly is 1737HG, and the complete light gray neck it lives in is 2307HG.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2952HG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e light gray\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e FELIX Premium, and ET-1 power heads with or without the on\/off switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNeck reference:\u003c\/strong\u003e swivel neck 2307HG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 118 on the FELIX sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlternative finish:\u003c\/strong\u003e gray black cap 2952GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 1737HG release button with leaf spring, 2951HG socket cover, 2945HG slide\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eIt is a small moulding with an outsized effect on how the machine handles, and it is the first thing to replace when a SEBO FELIX Premium handle release stops feeling positive. Both finishes cover the same button and share position 118 on the parts list, so the suffix on the number is what separates them rather than anything you can see in the drawing. Fitting is quick with the neck already open, and doing it at the same time as the socket cover and slide saves taking the joint apart twice for parts that all live within two positions of each other. Genuine SEBO component from an authorized dealer. Ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214525817082,"sku":"2952HG","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/20d1f5f0f69fb00b77f133370f88abec.jpg?v=1786668940"},{"product_id":"button-cover-on-et-1-for-dart-gray-black","title":"SEBO Release Button Cover for the DART and ET-1 Power Head — Gray Black","description":"\u003cp\u003eGray black moulded plastic caps the release button on the ET-1 power head, and 2962GS is the factory replacement SEBO supplies for it. The cap spreads pressure from a foot or a thumb across the button underneath and keeps the dust a working head throws around out of the release mechanism. SEBO fits it to the DART and to ET-1 power heads in both the switched and the unswitched build, and the gray black finish is what matches it to the neck hardware around it rather than to the coloured power head shells.\u003c\/p\u003e\u003cp\u003eSEBO draws the button cover as item 118 on the DART parts sheet. Immediately below it at 117 sits the release button with its leaf spring, part 1737GS, and the socket cover for the TS neck is alongside at 120 as part 2961GS; all three come into view in the same strip-down, so it is worth looking at the set together. Worn caps go glassy and slick, and the foot slides off mid-press. Cracked ones let the button rock in its aperture, and the release loses its clean single-press action — usually described as a neck that refuses to let go first time. A cap that has broken away completely leaves the button stem open to grit, and the mechanism stiffens from there.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2962GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e the SEBO DART, and ET-1 power heads with or without the switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 118 on the DART parts sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction:\u003c\/strong\u003e protective cap over the neck release button\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated numbers:\u003c\/strong\u003e 1737GS release button with leaf spring at 117, 2961GS socket cover at 120\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied:\u003c\/strong\u003e as a single cover\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA search for a SEBO button cover, a DART release button cap or simply for part 2962GS lands on this same small component, and swapping it takes minutes once the head is on the bench and the neck hardware is exposed. Supplied genuine by an authorized SEBO dealer, shipping in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214525849850,"sku":"2962GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2962GS.jpg?v=1709347866"},{"product_id":"socket-cover-ts-neck-for-et-1-et-2-felix-except-white-and-disco-gray-black","title":"SEBO TS-Neck Socket Cover for FELIX, ET-1, ET-2 and DISCO \u0026mdash; Gray Black","description":"\u003cp\u003ePower reaches the brush motor through contacts in the neck, and 2951GS is the gray black cap that closes over them. It keeps carpet fluff and grit off the connection point where the power head joins the machine, in a spot that sits low down and collects everything the floor has to offer.\u003c\/p\u003e\u003cp\u003eSEBO places the socket cover at position 120 on both the ET-1\/ET-2 power head diagram and the FELIX sheet, next along from the swivel neck slide at 119. A cracked or absent cap tends to announce itself electrically rather than visually: the brush roll cuts in and out as the neck flexes, because nothing is holding the connection square any more. Unplug the machine at the outlet before opening the neck, and check the swivel neck wiring, part 0876ER, for chafing while the contacts are exposed.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2951GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched, and the DISCO floor polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 120 on the power head and FELIX sheets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther finish:\u003c\/strong\u003e light gray cap 2951HG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 0876ER swivel neck wiring, 2945GS slide, 2952GS release button cover, 2947GS back cover\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSafety step:\u003c\/strong\u003e disconnect from the outlet before working on the neck\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eAn intermittent brush roll is one of the more frustrating faults to chase on a SEBO ET-1, and a missing socket cover is among the first causes worth ruling out before anything electrical is condemned. Genuine SEBO part, authorized dealer stock, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214526013690,"sku":"2951GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/f79c4382de9b7ab7eece7ba8e5737685.jpg?v=1786668928"},{"product_id":"socket-cover-ts-neck-for-felix-white-and-et-1-light-gray","title":"SEBO TS-Neck Socket Cover for FELIX Premium and ET-1 Power Heads \u0026mdash; Light Gray","description":"\u003cp\u003eA missing cap over the TS-neck socket leaves bare contacts sitting in the dust path, which is the last place they should be. Part 2951HG is the light gray replacement, sized to sit over the socket on the neck and shield the link between machine and power head.\u003c\/p\u003e\u003cp\u003eOn the FELIX parts diagram it is item 120, one along from the swivel neck slide at 119. Most of these fail from age rather than abuse: the plastic hardens over a decade of service, then one knock against a door frame splits it. Renewing the cap keeps the contact area enclosed and stops grit packing in around the terminals, which is what eventually turns a clean connection into an intermittent one. Take the plug out of the wall before the neck comes apart, and give the swivel neck wiring, 0876ER, a look for chafing while everything is open.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2951HG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e light gray\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e FELIX Premium, and ET-1 power heads with or without the on\/off switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 120 on the FELIX schematic\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e protects the electrical socket in the swivel neck\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDarker finish:\u003c\/strong\u003e gray black version listed as 2951GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 0876ER neck wiring, 2945HG slide, 2952HG release button cover, 2947HG back cover\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eOwners searching for a SEBO FELIX Premium socket cover are usually holding two halves of a split cap, and the light gray moulding is the one that matches pale trim. The gray black version carries a different suffix and looks wrong against a light head even though it does the same job, so order by the finish in front of you. Fitting takes a screwdriver and a few minutes with the neck already parted, and it is the sort of repair worth doing the moment the old cap starts to move rather than waiting for it to disappear. Sold as genuine SEBO by an authorized dealer, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214526111994,"sku":"2951HG","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/f8134ef36fbe1c8bae5c9772d3ff8892.jpg?v=1786668933"},{"product_id":"socket-cover-ts-neck-on-et-1-for-dart-gray-black","title":"SEBO TS-Neck Socket Cover for the DART and ET-1 Power Head \u0026mdash; Gray Black","description":"\u003cp\u003eDART owners replacing the socket cap on the ET-1 head need this exact version, 2961GS in gray black. It closes over the electrical socket in the TS-neck so the contacts feeding the brush motor stay covered while the head swivels along underneath the machine.\u003c\/p\u003e\u003cp\u003eSEBO's DART parts diagram carries it at position 120, two places on from the release button and its leaf spring at 117 and the button cover at 118. Age and handling do most of the damage here: the cap gets gripped whenever the neck is separated, and a hairline split eventually runs far enough that the piece drops away, leaving the socket open to whatever the head picks up off the floor. Once that happens the connection stops being held square, and a brush roll that cuts in and out as the neck flexes usually follows.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2961GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e the DART, and ET-1 power heads with or without the on\/off switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 120 on the DART sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCovers:\u003c\/strong\u003e the electrical socket inside the TS-neck\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2962GS button cover at 118, 1737GS release button with leaf spring at 117, 2954 swivel neck bearing at 122, 2309GS complete neck assembly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBefore starting:\u003c\/strong\u003e disconnect the machine from the outlet\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eTwo similar caps exist in the SEBO catalogue and they are not interchangeable listings, so order by the number on this page when the head in front of you is the DART build. The neck also carries a button cover and a release button within three positions of the socket cap, and all three take a beating from the same handling, which makes it worth checking them together while the joint is open. Keeping the socket enclosed is what stops a clean contact turning into an intermittent one. Genuine SEBO part held on an authorized dealer account. Ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214526177530,"sku":"2961GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/110420b00da0c9f2fc45881beeb128d6.jpg?v=1786669154"},{"product_id":"lens-left-without-on-off-switch-for-et-1-and-et-2","title":"SEBO Left Lens for ET-1 and ET-2 Power Heads — Switchless Version","description":"\u003cp\u003eClouded or cracked, a lens is a cosmetic fault that also lets grit reach the front of the nozzle. SKU 20955 is the left-hand lens moulded for the ET-1 and ET-2 power head families in the configuration supplied with no on\/off rocker, and it covers the light aperture at the leading corner of the head.\u003c\/p\u003e\u003cp\u003eTwo details decide whether this is the right ordering choice. The first is side: left and right lenses carry separate part numbers and do not interchange, so set the head down on its sole plate, look at it from the operating position, and work out which corner you are replacing before ordering. The second is switch layout, because heads built with an on\/off rocker use different front mouldings and a lens lifted from one will not seat properly in the other. Get either wrong and the new part sits proud of its recess instead of clipping flush, which puts it straight back in the firing line of the next chair leg.\u003c\/p\u003e\u003cp\u003eReplacement is usually prompted by a lens gone milky enough to dim the light it sits over, one starred by an impact, or one that has lost a retaining tab and keeps working its way out on corners. Fitting it into a clean recess matters more than it sounds, since grit trapped behind the moulding will crack the next one just as quickly. SEBO also lists this lens against the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium, all of which are supplied with power heads from the same families, so canister owners can order the same number with confidence.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits ET-1 and ET-2 power heads supplied with no on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 20955\u003c\/li\u003e\n\u003cli\u003eAlso listed by SEBO for the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eLeft-hand side; the right-hand lens is a separate number\u003c\/li\u003e\n\u003cli\u003eClear moulded lens, genuine SEBO\u003c\/li\u003e\n\u003cli\u003eSold individually\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eShips in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214528307450,"sku":"20955","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/ea22de16f3c40a252791f6381e55bf41.jpg?v=1786670157"},{"product_id":"on-off-button-lens-for-et-1-and-et-2","title":"SEBO On\/Off Button Lens for Switched ET-1 and ET-2 Power Heads","description":"\u003cp\u003eSwitched power heads carry a small moulded lens over the on\/off control. Part 2957 is that piece: the face your thumb presses and the cover that keeps carpet dust away from the switch sitting behind it.\u003c\/p\u003e\u003cp\u003eSEBO lists it at position 139 on the ET-1\/ET-2 power head diagram, where it is noted as the left hand item, at 139 on the FELIX sheet and at 136 on the DART. Yellowing, a star crack across the face, or a lens that has popped out and vanished under the sofa are the reasons this part gets ordered. Because the lens is only a cover, it is worth confirming that the switch itself still operates cleanly while the head is open: the single pole switch is 05114, the lever and leaf spring behind it are 2958ER, and SEBO sells the whole switch group built up as 2959ER if the fault turns out to be electrical rather than cosmetic.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2957\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads built with the on\/off switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 139 on the power head and FELIX sheets, 136 on the DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e button face and dust cover for the head's on\/off switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2956 brush light lens at 140, 05114 switch, 2958ER lever with leaf spring, 2959ER complete switch assembly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCheck first:\u003c\/strong\u003e confirm the switch still latches before blaming the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eUnswitched heads have no lens to lose, so check which build you have before ordering a SEBO ET-1 on\/off button lens. The brush light lens on the other side of the head is 2956, a different moulding at the next position along, and the two are easy to confuse when working from the drawing rather than the number. Genuine SEBO stock from an authorized dealer; ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214528340218,"sku":"2957","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/c4e52fcde7b157052422e5b0922e5a20.jpg?v=1786668948"},{"product_id":"lens-right-brush-light-for-et-1-and-et-2","title":"SEBO Brush Light Lens, Right Hand, for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eClear plastic keeps grit off the brush light while letting the beam through, and 2956 is the right hand lens for that duty. It seats in the power head housing over the lamp, taking the scuffs and knocks that come from working tight against baseboards, table legs and stair risers.\u003c\/p\u003e\u003cp\u003eSEBO catalogues the right hand lens at position 140 on the ET-1\/ET-2 diagram, at 140 on the FELIX sheet and at 137 on the DART, immediately alongside the on\/off button lens. Lenses cloud with age and crack on impact, and a hazed lens dims the light long before the lamp behind it gives up, which is why a machine that seems to have lost its brush light often only needs the plastic changed. Wipe out the lamp recess while the lens is off the head, and check the seat for old grit so the new lens sits flush rather than proud.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2956, right hand lens\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 140 on the power head and FELIX sheets, 137 on the DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e protects and covers the brush light in the head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2957 on\/off button lens at 139, 2684ER printed circuit board\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTip:\u003c\/strong\u003e clean the lamp recess before the new lens goes in\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eBuyers hunting a SEBO ET-2 brush light lens replacement should note the handing: this is the right hand moulding, and the switch lens on the other side of the head is a separate number entirely. Both sit within one position of each other on the same diagram, so it is easy to order the wrong one from a drawing alone. Genuine SEBO lens supplied through an authorized dealer, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214528372986,"sku":"2956","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2956_411f9f5a-468b-4659-aca8-e6fd83aa6b4e.jpg?v=1785142869"},{"product_id":"foot-pedal-with-axle-and-spring-for-et-1-et-2-and-disco-orange","title":"SEBO Foot Pedal with Axle and Spring for FELIX, ET-1, ET-2 and DISCO \u0026mdash; Orange","description":"\u003cp\u003eOrange plastic, a steel pivot pin and a return spring arrive together as one item in 2937OR. Step on the pedal and the handle unlocks from upright so the machine can be reclined for a pass under a table; lift your foot and the spring carries the pedal back, ready for the next release.\u003c\/p\u003e\u003cp\u003eSEBO draws the pedal at position 112 on the ET-1\/ET-2 power head sheet, at 112 on the DART diagram and at 112 on the FELIX diagram, with the wheel at 111 on one side of it and the complete swivel neck at 113 on the other. The DISCO floor polisher parts list carries the same pedal at position 24. Fit a new one when the handle drops loose the moment the pedal is brushed, when the pedal stays down after being pressed, or when a snapped spring leaves the lock rattling as you push. Since the pin and spring come in the pack, nothing has to be salvaged off the old assembly.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2937OR\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied as:\u003c\/strong\u003e pedal, axle and return spring together\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e orange\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched, and the DISCO floor polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 112 on the power head, DART and FELIX sheets; 24 on the DISCO list\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2306GS wheel at 111, 2307GS complete swivel neck at 113\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis is one of the most-searched SEBO FELIX pedal repairs for a reason: the pedal takes a boot every time the machine is used, and it is the part that decides whether the handle release still feels positive. German-made SEBO component from an authorized dealer, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214528733434,"sku":"2937OR","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2937OR_efad1f05-495b-44c7-8c75-1a58885a96c8.jpg?v=1785139812"},{"product_id":"bearing-segments-metal-ts-neck-for-all-et-1-et-2-and-disco-swivel-necks-6-pc-set","title":"SEBO Metal Bearing Segments for the TS-Neck Swivel \u0026mdash; 6 Piece Set","description":"\u003cp\u003eSix machined metal segments carry the load inside a SEBO TS-neck swivel, and 2950ER supplies the full set. They ring the joint between power head and neck, spreading steering forces so the head turns on metal instead of grinding plastic against plastic.\u003c\/p\u003e\u003cp\u003eSEBO shows the segments as a six-piece set at position 116 on the ET-1\/ET-2 power head diagram and at 116 on the FELIX sheet, with the DISCO floor polisher list carrying them at position 7. Change all six together. Mixing tired segments with new ones loads the joint unevenly, and the swivel keeps the notchy, sloppy feel that sent you looking for this part in the first place. The two neighbours on the same diagram wear at a similar rate, so pull the slide 2945GS at position 119 and the swivel neck bearing 2954 at 122 while the joint is open and judge all three together.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2950ER\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack:\u003c\/strong\u003e six metal segments, sold as one complete set\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e metal, for the TS-neck swivel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e the TS-neck swivel on ET-1 and ET-2 power heads, switched and unswitched, and on the DISCO floor polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 116 on the power head and FELIX sheets, 7 on the DISCO list\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2945GS and 2945HG slides, 2954 neck bearing, 2947GS back cover\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eOf every part in a SEBO ET-1 or ET-2 swivel neck rebuild, this set does the most to bring back a tight, quiet joint, because it is the metal that actually takes the steering load rather than the plastic wrapped around it. Fitting the set is a strip-and-rebuild of the neck, so it is worth ordering everything the joint needs in one go. Authorized SEBO dealer supply, out the door in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214531027194,"sku":"2950ER","price":14.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/efa97c3bba2028741c79821e4c216750.jpg?v=1786668925"},{"product_id":"lever-with-leaf-spring-for-et-1-and-et-2","title":"SEBO Switch Lever with Leaf Spring for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eBetween your thumb and the electrical contacts sits a lever backed by a leaf spring, and 2958ER supplies both as one piece. The spring gives the on\/off action its snap and returns the lever to rest after each press, so the control commits to on or to off rather than hovering somewhere between the two.\u003c\/p\u003e\u003cp\u003eSEBO draws the lever at position 131 on the ET-1\/ET-2 power head sheet, at 131 on the FELIX diagram and at 139 on the DART, where it sits with the single pole switch 05114 and the wire 0881 in the group that makes up the complete switch. A tired or broken spring shows up as a mushy button, a lever that stays pushed in, or a brush roll that shuts itself off when the head takes a knock against a chair leg. The lever is also supplied inside the built-up assembly 2959ER, which is the better choice when the switch body or its wiring has failed as well.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2958ER, lever and leaf spring together\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 131 on the power head and FELIX sheets, 139 on the DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e gives the on\/off control its travel, snap and return\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2959ER complete switch assembly, 05114 single pole switch, 0881 wire to the board, 2957 button lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eWhen a SEBO ET-1 switch feels dead under the thumb but the machine still runs, the lever and its spring are the parts to look at before anything electrical gets condemned, and they are far less work to change than the board behind them. Genuine SEBO parts, authorized dealer supply, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214532763898,"sku":"2958ER","price":8.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2958ER.jpg?v=1785151879"},{"product_id":"swivel-neck-slide-for-et-1-et-2-felix-except-white-and-disco-gray-black","title":"SEBO Swivel Neck Slide for FELIX, ET-1, ET-2 and DISCO \u0026mdash; Gray Black","description":"\u003cp\u003eSteering feel comes from the swivel neck, and the slide is the piece that guides it. Finished in gray black, 2945GS rides in the neck joint linking head to handle, holding the pivot on a controlled path as the machine is swept left and right along a wall.\u003c\/p\u003e\u003cp\u003eSEBO draws this slide at position 119 on the ET-1\/ET-2 power head sheet and at the same number on the FELIX diagram, one place after the button cover at 118 and one before the socket cover at 120. A slide worn thin lets the neck feel loose and vague; one that has scored or picked up grit makes the head fight every change of direction. Either symptom points straight at this part. While the joint is apart it is worth checking the two components that share the load with it: the six-piece metal segment set 2950ER at position 116 and the swivel neck bearing 2954 at 122. If the neck itself is cracked rather than merely worn, the complete gray black assembly is 2307GS at 113.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2945GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched, and the DISCO floor polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 119 on the power head and FELIX sheets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish check:\u003c\/strong\u003e the light gray equivalent is stocked separately as 2945HG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2950ER segment set, 2954 neck bearing, 2947GS back cover, 2951GS socket cover\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eSearches for a SEBO ET-2 swivel neck repair usually end at one of three parts, and the slide is the one to rule out before committing to a full rebuild of the joint. Authorized SEBO dealer stock, dispatched in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214533714170,"sku":"2945GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0d89380aa5368074327b0d406778b531.jpg?v=1786668915"},{"product_id":"swivel-neck-slide-for-felix-white-and-et-1-light-gray","title":"SEBO Swivel Neck Slide for FELIX Premium and ET-1 Power Heads \u0026mdash; Light Gray","description":"\u003cp\u003eLight gray bodywork takes the matching slide, part 2945HG. It sits inside the swivel neck and guides the pivot where the head meets the handle, so the nozzle follows your wrist instead of drifting wide of the line you are steering.\u003c\/p\u003e\u003cp\u003ePosition 119 on SEBO's FELIX parts diagram marks this component, sitting between the button cover at 118 and the socket cover at 120. Years of steering wear the bearing face down, and the result is felt rather than seen: a neck that flops when the machine is stood up, or one that grinds and resists as you turn along a baseboard. Renewing the slide tightens the joint back up. Because the same joint carries two other wear items, it is worth pulling the metal segment set 2950ER at position 116 and the swivel neck bearing 2954 at 122 for inspection while everything is apart. A neck that has cracked rather than worn is replaced complete as 2307HG in light gray.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2945HG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e light gray\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e FELIX Premium, and ET-1 power heads with or without the on\/off switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 119 on the FELIX schematic\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRole:\u003c\/strong\u003e guides the pivot inside the swivel neck\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther finish:\u003c\/strong\u003e gray black slide 2945GS is listed separately\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2950ER segment set, 2954 neck bearing, 2947HG back cover, 2951HG socket cover\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eMatch by trim colour before ordering, since the light gray and gray black slides do the same job but look plainly different once the head is back together. Both share position 119 on the FELIX list, so the drawing will not separate them and the suffix on the part number is what matters. Fitting is a bench job with the neck already open, which is the argument for doing the segments and bearing in the same sitting rather than twice. Genuine SEBO spare from an authorized dealer; ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214533746938,"sku":"2945HG","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/5750dacc5fe3c80c16cf108881bb5dc2.jpg?v=1786668917"}],"url":"https:\/\/evacuumsandmore.com\/collections\/sebo-et-1.oembed?page=4","provider":"Vacuums and More","version":"1.0","type":"link"}