{"title":"Sebo Et-2","description":null,"products":[{"product_id":"axle-for-swivel-neck-supports-for-et-1-and-et-2","title":"SEBO Swivel Neck Support Axle for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eEvery change of direction is absorbed by the neck joint between wand and power head. Part 2928 is the axle the swivel neck supports turn on, drawn at position 126 on SEBO's ET-1\/ET-2, DART and FELIX parts sheets, sitting one number along from the neck switch wiring that runs through the same joint.\u003c\/p\u003e\u003cp\u003eWear here is felt rather than seen. The head starts to lag behind the handle, flops at the end of a stroke, or refuses to follow into a turn at all. The right and left supports the shaft passes through are listed separately as 2311 and 2312 at positions 123 and 124, and they wear in step with it, so put a thumb on both and check for play while the joint is open. If the swivel also feels notchy rather than merely loose, the six-piece metal segment set 2950ER and the swivel neck bearing 2954 are the next two items on the same sheet worth inspecting. Disconnect the machine from the outlet before disturbing anything that carries power down into the head.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2928, supplied singly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e pivot shaft carrying the swivel neck supports\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 126 on the ET-1\/ET-2, DART and FELIX lists\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2311 support right, 2312 support left, 2954 swivel neck bearing, 2950ER metal segment set, 2307GS complete swivel neck\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTypical symptom:\u003c\/strong\u003e a head that wanders, flops or fights the line you are steering\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA SEBO ET-1 axle replacement is a bench job rather than a roadside one, but it is the quickest way to bring the steering back to where it was, and always worth doing while the neck is apart for any other reason. Genuine SEBO stock from an authorized dealer; ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214472339706,"sku":"2928","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2928.jpg?v=1709347663"},{"product_id":"bearing-block-l-h-complete-for-et-1-and-et-2-gray-black","title":"SEBO Left-Hand Bearing Block for ET-1 and ET-2 Power Heads — Gray Black","description":"\u003cp\u003ePosition 102 on SEBO's exploded views marks the left-hand brush roll bearing, and 2314GS is that component in gray black, assembled and ready to seat. The same position number applies across the ET 1 \/ ET 2 power head, DART and FELIX diagrams, so whichever sheet you are working from the reference holds.\u003c\/p\u003e\u003cp\u003eLeft and right blocks are not interchangeable and carry separate part numbers, so identify which end has gone noisy before ordering. Grinding under load, a roll that will not turn freely by hand, or visible play when you rock the roll in its seat all point at the bearing rather than the belt. The distinction matters because a slipping belt and a failed bearing can both leave a head that cleans poorly on carpet, yet the fix and the part are entirely different. With the roll out, spin each bearing on its own: a healthy one runs on smoothly for a few seconds, a failed one feels notchy or stops immediately, and a housing that has worn oval will let the whole bearing turn in its seat.\u003c\/p\u003e\u003cp\u003eBecause both ends accumulate identical hours, pairing this with the right-hand block, part 2313GS, avoids taking the head apart twice. Clear wound hair and thread from the roll shaft before reassembly, since that binding is what loads the bearings in the first place, and check the belt runs central on its pulley once everything is back together. Light gray ET-1 heads use the colour-matched block 2314HG instead of this one.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 as well as ET-2 power heads, switched or unswitched\u003c\/li\u003e\n\u003cli\u003ePart number: 2314GS\u003c\/li\u003e\n\u003cli\u003eLeft-hand brush roll bearing block, supplied complete with the bearing seated\u003c\/li\u003e\n\u003cli\u003eFinish: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 102 in the ET 1 \/ ET 2, DART and FELIX parts lists\u003c\/li\u003e\n\u003cli\u003eRelated numbers: 2313GS right-hand block, 2314HG in light gray\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO part. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214472962298,"sku":"2314GS","price":30.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2314GS.jpg?v=1785150350"},{"product_id":"bearing-block-r-h-complete-for-et-1-and-et-2-gray-black","title":"SEBO Right-Hand Bearing Block for ET-1 and ET-2 Power Heads — Gray Black","description":"\u003cp\u003eA brush roll that squeals at one end, wanders sideways, or takes a moment to come up to speed has usually lost a bearing. Part 2313GS is the right-hand half of that pair in the gray black finish, and it ships complete, so the bearing already sits in its housing and the repair is a swap rather than a press-fit rebuild on the bench.\u003c\/p\u003e\u003cp\u003eSEBO draws this piece at position 105 in the ET 1 \/ ET 2 power head diagram, and at position 105 again in the DART and FELIX diagrams. The failure has a recognisable arc. First comes a rise in running noise that tracks brush speed rather than motor speed, then the belt begins creeping toward one end of its pulley, and finally the roll develops enough play to be rocked visibly in its seat by hand. Left long enough, an out-of-square roll wears its own end cap and starts scrubbing the carpet harder on one side of the opening than the other.\u003c\/p\u003e\u003cp\u003eLook over the opposite end while the roll is out. The left-hand block, part 2314GS in the same finish, carries identical hours and tends to wear on much the same schedule, and doing both at once avoids a second strip-down. Clear wound hair from the roll shaft before reassembly, since that binding loads the bearings every time the head runs. Light gray ET-1 heads take block 2313HG instead, so order by the finish on the head in front of you. Fitment on this gray black block runs across both head widths, which is why one number covers uprights and canisters alike.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 as well as ET-2 power heads, switched or unswitched\u003c\/li\u003e\n\u003cli\u003ePart number: 2313GS\u003c\/li\u003e\n\u003cli\u003eRight-hand brush roll bearing block, supplied complete with the bearing seated\u003c\/li\u003e\n\u003cli\u003eFinish: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 105 in the ET 1 \/ ET 2, DART and FELIX parts lists\u003c\/li\u003e\n\u003cli\u003eRelated numbers: 2314GS left-hand block, 2313HG in light gray\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO part. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214473552122,"sku":"2313GS","price":18.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2313GS_74be7a83-888a-4bc1-812f-9e2c64caf642.jpg?v=1785153960"},{"product_id":"belt-333-3m-htdii-6-for-et-1-et-2-softcase-and-370-comfort","title":"SEBO Toothed Brush Belt 333 3M HTDII-6 for FELIX, DART, ET-1\/ET-2 and 370 COMFORT","description":"\u003cp\u003eA toothed belt cannot slip the way a smooth one does, which is why SEBO drives its brush rolls through a geared profile rather than a flat rubber loop. Part 2923 is the 333 3M HTDII-6, the same belt the SOFTCASE CE12 parts list records under the heading toothed belt 333 HTD 3M 6. It sits at position 103 on the ET-1\/ET-2, DART and FELIX sheets and at position 125 on the SOFTCASE CE12.\u003c\/p\u003e\u003cp\u003eThis is the one true consumable in the drive train. Everything else in the head is metal or moulded plastic; the belt is rubber, it is under constant tension, and it wears whether the machine is used hard or gently. A stretched belt announces itself as a brush that free-wheels, ticks under load, or gives up altogether in deep pile while the suction motor sounds entirely normal. One that has begun shedding teeth leaves black crumbs of its own inside the head, and a belt that has been run slack long enough will glaze and start to smell hot. Because the geared profile has to mesh, a tired belt also chews the pulley it runs on, so replacing it early is the cheaper decision.\u003c\/p\u003e\u003cp\u003eFull fitment is broad: the SEBO ET-1 and ET-2 power heads in both with-switch and without-switch versions, the FELIX Premium and FELIX 2 Premium, the DART, the 370 COMFORT, the CE12 SOFTCASE, the AIRBELT D4 PREMIUM, the AIRBELT E3 Premium, the AIRBELT K3 PREMIUM and the C3.1. On the 370 COMFORT it pairs with brush pulley 2919ER, and motor pulley 2319 is the driven end on the FELIX Premium, FELIX 2 Premium, DART, 370 COMFORT, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM, C3.1 and both ET heads. Access door 2909VO is the orange flap that has to come off to reach it. Keep a spare on the shelf; this is the part that strands a machine mid-room.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSEBO part 2923 — belt 333 3M HTDII-6, toothed\u003c\/li\u003e\n\u003cli\u003eFits: SEBO ET-1 and ET-2 power heads (with or without switch), FELIX Premium, FELIX 2 Premium, DART, 370 COMFORT, CE12 SOFTCASE, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1\u003c\/li\u003e\n\u003cli\u003eParts-diagram positions: 103 (ET-1\/ET-2, DART, FELIX), 125 (SOFTCASE CE12)\u003c\/li\u003e\n\u003cli\u003eType: geared drive belt, so it meshes rather than gripping by friction\u003c\/li\u003e\n\u003cli\u003eTypical symptom: brush free-wheeling, ticking under load, or stalling in deep pile\u003c\/li\u003e\n\u003cli\u003eRelated part numbers: 2919ER brush pulley, 2319 motor pulley, 2909VO access door\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine SEBO\u003c\/strong\u003e; ships in 2–5 business days\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214474535162,"sku":"2923","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0f2340c355f940c6ecec795e4f1492c2.jpg?v=1786668775"},{"product_id":"rear-bottom-plate-for-et-2-gray-black","title":"SEBO Rear Bottom Plate for ET-2 Power Heads — Gray Black","description":"\u003cp\u003eOrder by head type rather than by appearance. The ET-2 floor nozzle is wider than its ET-1 sibling and takes its own rear panel, catalogued as SKU 2305GS in gray black and shown at position 109 of the ET 1 \/ ET 2 power head diagram as the complete rear bottom plate. The corresponding panel for the narrower head is 2304GS, and the two are not interchangeable.\u003c\/p\u003e\u003cp\u003eThe panel spans the back of the sole, keeping the trailing lip in even contact with the floor while sealing the air path behind the roll. Damage along that edge is common on machines dragged over thresholds and door bars, and the giveaway is a nozzle that rocks under hand pressure or leaves a thin line of debris trailing behind it. A second symptom is a head that suddenly feels light on carpet, because air is entering behind the roll instead of being drawn through the pile in front of it. None of that improves with a fresh bag or a clean filter, which is why the fault so often gets chased in the wrong place first.\u003c\/p\u003e\u003cp\u003eDiagnosis takes a minute with the head upside down on a bench. Sight along the rear lip for a bow, run a fingernail along it for thin spots, and press each end down to see whether the panel flexes away from the shell. If a felt or foam seal came off with the old plate, move it across unless the new one already carries its own. Clear the packed hair that collects along the back of the roll while the underside is open, because that debris holds the panel off its seat and starts the cycle again on a brand new plate.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX 2 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-2 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2305GS\u003c\/li\u003e\n\u003cli\u003eColour: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 109, ET 1 \/ ET 2 power head parts list\u003c\/li\u003e\n\u003cli\u003eSupplied complete\u003c\/li\u003e\n\u003cli\u003eRelated number: 2304GS, the ET-1 equivalent rear bottom plate\u003c\/li\u003e\n\u003cli\u003eSeals the air path behind the brush roll and sets the trailing lip height\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO part, listed for anyone searching a FELIX 2 Premium sole plate or an ET-2 rear bottom plate replacement. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214476108026,"sku":"2305GS","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/6f00fa1488e4e542af598d1d86ed21d0.jpg?v=1786669681"},{"product_id":"bumper-for-et-2-gray-black","title":"SEBO ET-2 Power Head Bumper — Gray Black","description":"\u003cp\u003eWider heads take their own trim, and 2303GS is the gray black bumper SEBO supplies for the ET-2 floor nozzle. The ET 1 \/ ET 2 power head diagram shows it at position 101 as the complete bumper, and despite the family resemblance it does not interchange with the narrower ET-1 moulding, which is ordered as 2302GS in the same finish.\u003c\/p\u003e\u003cp\u003eBumpers earn their keep along room edges, where the head meets skirting on very nearly every pass. The wear pattern reflects that: the corners go first, the retaining channel loses its grip next, and eventually a length of the strip stands away from the shell. Once the trim cracks or pulls out, those impacts land on the housing instead, and scuffs start appearing on the machine and on the furniture alike. A strip that rattles when the head is shaken has already let go of its channel even if it still looks intact from above, so check by feel rather than by eye.\u003c\/p\u003e\u003cp\u003eReplacement is a direct swap along the front edge with the nozzle laid on its back. Clean the groove out before pressing the new moulding in, work from one corner across rather than pushing the middle down first, and run a thumb along the finished edge to confirm it sits level with the shell. This part is listed by SEBO for the FELIX 2 Premium, and it suits ET-2 heads whether or not they were built with an on\/off rocker, so the switch layout of your own machine does not change the order.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX 2 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-2 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2303GS\u003c\/li\u003e\n\u003cli\u003eColour: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 101, ET 1 \/ ET 2 power head parts list\u003c\/li\u003e\n\u003cli\u003eSupplied complete\u003c\/li\u003e\n\u003cli\u003eRelated number: 2302GS, the equivalent bumper for the narrower ET-1 head\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO trim for anyone searching a FELIX 2 Premium bumper or an ET-2 nozzle bumper replacement. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214478074106,"sku":"2303GS","price":20.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2303GS_1e6fa52f-e135-433f-9e39-0037e4e6d234.jpg?v=1785143136"},{"product_id":"pile-adjustment-knob-for-et-1-and-et-2-gray-black","title":"SEBO Pile Adjustment Knob for ET-1 and ET-2 Power Heads \u0026mdash; Gray Black","description":"\u003cp\u003eCarpet height on an ET-1 or ET-2 power head is chosen with a single control, and 2931GS is it in gray black. SEBO shows the knob at position 110 on the ET-1\/ET-2 sheet, where the DART list files the same position under pile adjustment button. Turning it steps the brush roll up or down so the bristles meet plush, medium or low carpet at a sensible depth instead of skating over the fibers or stalling in them.\u003c\/p\u003e\u003cp\u003eKnobs catch on furniture legs and split at the hub long before the mechanism underneath gives out. A cracked hub turns without driving the shaft below it, which strands the head on whatever setting it was last left on, and a knob that has gone missing altogether leaves nothing to grip. Fitting a new one restores indexed selection without opening the rest of the adjustment group. If the detents themselves feel mushy rather than the knob feeling loose, look past this part to the spring at 106, part 2929, and to the complete pile adjustment assembly at 107, sold as 2316GS in gray black.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2931GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e gray black, matching the darker head trim\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 110 on the ET-1\/ET-2 sheet, and 110 on the DART list as the pile adjustment button\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther finishes:\u003c\/strong\u003e 2931HG in light gray, 2931SB in silver\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2316GS adjustment assembly, 2929 spring\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eOrder by finish rather than by feel: gray black, light gray and silver knobs share the same fitting but look plainly different on the head. Genuine SEBO part from an authorized dealer, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214480597242,"sku":"2931GS","price":8.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0733ea0293158c3f0fa21738f6b746bf.jpg?v=1786668905"},{"product_id":"pile-adjustment-knob-for-et-1-and-et-2-silver","title":"SEBO Pile Adjustment Knob in Silver for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eSilver is the third finish SEBO offers for the height control on its power heads, and 2931SB is that knob. It is the round dial on the head that steps the brush roll up or down to suit the floor underneath: low for flat commercial loop, high for deep pile, so the brush works the fibers instead of stalling against them.\u003c\/p\u003e\u003cp\u003eThe diagrams place the silver knob at position 110 for ET-1 and ET-2 power heads, and again at position 110 on the FELIX sheet. Worn detents are the usual reason one gets ordered. The knob turns too freely, the chosen height no longer holds, and brush contact changes by itself halfway through a room. A split hub is the other common failure, and it shows up as a control that spins without moving anything. Should a new knob fail to cure it, the spring behind the mechanism is 2929 at position 106 and the complete adjustment assembly is 2316GS at 107.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2931SB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e silver\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 110 on the power head sheet and on the FELIX sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction:\u003c\/strong\u003e sets brush roll height by carpet pile depth\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther finishes:\u003c\/strong\u003e 2931HG in light gray, 2931GS in gray black\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eMachines left the factory with different trim, so match the finish already on the head rather than assuming: silver, light gray and gray black knobs interchange mechanically but look nothing alike in place. All three share the same diagram position, which means the drawing alone will not tell them apart and the part number has to do the work. Supplied as factory SEBO stock through an authorized dealer account, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214480892154,"sku":"2931SB","price":8.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/479e9b47e3f9212791c63bcf5b2d2111.jpg?v=1786668910"},{"product_id":"wiring-for-swivel-neck-for-et-1-et-2-and-disco","title":"SEBO Swivel Neck Wiring for ET-1, ET-2 and DISCO Power Heads","description":"\u003cp\u003eOf all the wiring inside a power head, the run through the swivel neck is the one that actually moves. It twists and flexes with every turn of the head and every change of direction, and part 0876ER is the pre-made loom SEBO supplies for exactly that section.\u003c\/p\u003e\u003cp\u003eFlex fatigue is gradual and then sudden. Strands break one at a time inside insulation that still looks perfect, so the brush roll starts cutting out at a particular angle of the handle, comes back when the head is straightened, and eventually stops for good. Fits the ET-1 and ET-2 power heads in both switched and unswitched builds, the DISCO Floor Polisher, and the machines these heads are supplied on: FELIX Premium, FELIX 2 Premium, DART, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and the C3.1.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e SEBO 0876ER, swivel neck wiring\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 114 on the SEBO ET 1 \/ ET 2, DART and FELIX sheets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTypical fault:\u003c\/strong\u003e the roller drops out as the head is steered, then returns when it is straightened\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied:\u003c\/strong\u003e made up to length with its terminations already fitted\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated power head wiring:\u003c\/strong\u003e 0880 for the safety switch with its lead, 0881 for the board-to-switch harness\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMachines these heads ship on:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eWork the new loom through the neck's full range of movement before the housing goes back together, so nothing is trapped, stretched or pinched at the extremes of travel. Repeating the original routing matters more here than anywhere else in the machine, because this is the one length of wire that will be bent several thousand times a year.\u003c\/p\u003e\u003cp\u003eGenuine SEBO swivel neck wiring for ET-1 and ET-2 power heads, ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214487118074,"sku":"0876ER","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0876ER.jpg?v=1785156314"},{"product_id":"wiring-from-pcb-to-on-off-switch-for-et-1-and-et-2","title":"SEBO On\/Off Switch Wiring Harness for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eShort looms take the worst of the vibration, and the run from the on\/off switch back to the board inside an ET power head is one of the shortest on the machine. Part 881 replaces that harness complete on an ET-1 or ET-2 head.\u003c\/p\u003e \u003cp\u003eA conductor fatigued at its crimp gives a switch that works when it feels like it: the head starts, dies as soon as the wand is flexed, then behaves perfectly on the bench a minute later. Because the fault follows movement rather than temperature or run time, it is one of the more frustrating ones to chase, and it is often mistaken for a failing switch or a tired brush motor. Renewing the loom brings back a positive, repeatable switch action, and it is worth looking closely at the switch contacts themselves while the wiring is out of the housing, since the two components fail from the same cause and at roughly the same age.\u003c\/p\u003e \u003cul\u003e \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 881\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eMachines:\u003c\/strong\u003e SEBO ET-1 and ET-2 power heads\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eFunction:\u003c\/strong\u003e factory loom joining the on\/off switch to the board\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003ePoints to it:\u003c\/strong\u003e switching that cuts in and out, a head that responds to being wiggled, a control that needs pressure held on it\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eInstall:\u003c\/strong\u003e match the connector orientation to the harness you remove\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eRelated:\u003c\/strong\u003e part 880, the micro safety switch with wiring for the same heads\u003c\/li\u003e \u003c\/ul\u003e \u003cp\u003eSymptoms separate this part from the interlock switch cleanly enough. Intermittent running, a head that answers to being wiggled, and switching that works one minute and not the next all sit with the harness. A head that stays completely silent from the moment it is connected sits with the micro safety switch, part 880, instead. Matching the symptom to the part first saves ordering both.\u003c\/p\u003e\u003cp\u003eUnplug the vacuum before opening the head, and route the new harness along the original path so it is not trapped when the housing closes. Searches for a SEBO ET-1 switch harness, an ET-2 on off wiring loom or a genuine SEBO power head wiring repair part land on 881. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214487249146,"sku":"881","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0881.jpg?v=1709349133"},{"product_id":"power-head-cover-for-et-2-without-on-off-switch-for-9251am-black","title":"SEBO ET-2 Power Head Cover — Black, No-Switch Configuration","description":"\u003cp\u003eGetting the switch configuration right is the whole job when you order a shell for an ET-2 nozzle. Part 20345SWET is the black top housing for SEBO ET-2 Power Heads built without an on\/off rocker, moulded solid where the switched version carries an opening. It is the cover supplied on machine 9251AM.\u003c\/p\u003e\u003cp\u003eIn SEBO's ET 1, ET 2 Power Heads exploded view this cover sits at position 135 and is described as the black ET-2 cover. Covers for the other head drawn on that same sheet carry different numbers at different positions, and the two look close enough in a photograph to be confused, so identify which nozzle is actually on the machine before ordering rather than judging by colour alone. The nozzle itself is normally marked, and the diagram position is the quickest way to confirm a match once you know which head you have.\u003c\/p\u003e\u003cp\u003eWhat the cover does is straightforward: it closes the top of the power head, encloses the drive, and holds the shape the rest of the nozzle is assembled to. Once it has cracked, grit reaches parts that were meant to stay covered and the fixings around the break stop pulling the housing together. Renewing the shell leaves the internal drive components alone; those carry their own part numbers and are ordered separately if they need attention at the same time.\u003c\/p\u003e\u003cp\u003eThis head runs a 15 inch roller, so a strip of hair across the full width is easy to miss when the shell is off. Clearing it, and checking the belt while the cover is away, turns a cosmetic repair into a proper service.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003ePart number: 20345SWET, genuine SEBO ET-2 power head cover\u003c\/li\u003e\n\u003cli\u003eColour: black, as fitted to machine 9251AM\u003c\/li\u003e\n\u003cli\u003eConfiguration: without on\/off switch, no rocker aperture\u003c\/li\u003e\n\u003cli\u003eDiagram position: 135 on the SEBO ET 1, ET 2 Power Heads parts list\u003c\/li\u003e\n\u003cli\u003eFits: SEBO ET-2 Power Heads supplied with no on\/off rocker\u003c\/li\u003e\n\u003cli\u003eDrive parts for the same head: belt 2923, motor pulley 2319, bearing blocks 2313GS and 2314GS, brush motor 2974ER, printed circuit board 2689ER\u003c\/li\u003e\n\u003cli\u003eWear items: 15\" brush roller 2838AM, soft-bristle roller 2838GE, brush roller cleaning tool 8366WS\u003c\/li\u003e\n\u003cli\u003eBody parts: bumper 2303GS, rear bottom plate 2305GS, chassis 2325GS, wheel 2306GS, access door 2909VO\u003c\/li\u003e\n\u003cli\u003eUpper housing only, supplied singly; ships in 2–5 business days\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214503239930,"sku":"20345SWET","price":32.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/ec165901acfd0dcc40d56a1d1c8f33a9.jpg?v=1786670654"},{"product_id":"power-head-cover-for-et-2-red","title":"SEBO ET-2 Power Head Cover - Red","description":"\u003cp\u003eEvery ET-2 head takes a shell sized to it, and 2341DRET is the red one, supplied plain with no name printed on the face. It closes the nozzle over the drive side and gives the head its visible color.\u003c\/p\u003e\u003cp\u003ePosition 135 in the ET 1 \/ ET 2 power head diagram is where SEBO draws it. That sheet title covers two head families on one drawing, so read it as the name of a diagram and let the part number do the work: this listing is recorded against ET-2 power heads built with the switch, and the shells drawn on the other half of that sheet are separate numbers entirely. Confirm which variant is on the machine before ordering, because switched and unswitched heads are not treated as interchangeable in SEBO parts listings.\u003c\/p\u003e\u003cp\u003eThe reason people come looking is usually mechanical rather than cosmetic. A shell that has cracked around a boss stops holding the head square, the joint opens under vibration, and grit that should stay outside ends up on the belt and pulley. Catching it early keeps the repair to one part. Fitting the replacement is straightforward with the head already apart, and that is the moment to look over the belt and the bristle strip while they are reachable.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2341DRET\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e red, plain, no print applied\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-2 power heads with the switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 135, SEBO ET 1 \/ ET 2 power head sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied as:\u003c\/strong\u003e the shell on its own, with no internal components\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNot included:\u003c\/strong\u003e belt, roller, switch or fixings\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther ET-2 shells:\u003c\/strong\u003e 2341SWET black, 2341WEET in white with the ET-2 print, and 2341WESE, the other printed white shell\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis is the genuine SEBO ET-2 power head cover in red, and the number to quote for an ET-2 nozzle top replacement. SEBO lists its small hardware individually as well, with screw 3.9 x 13 as 0102 and 0102ER for a ten pack. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214503272698,"sku":"2341DRET","price":31.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/ff07811abf9b8557d3f9a4df19a85812.jpg?v=1786670656"},{"product_id":"power-head-cover-for-et-2-black","title":"SEBO ET-2 Power Head Cover - Black","description":"\u003cp\u003eGrit that gets past a broken shell lands on the belt and pulley, which is the practical argument for replacing a cracked cover rather than living with it. Part 2341SWET is the black upper shell of the SEBO ET-2 power head, supplied plain, without a printed model name on the surface.\u003c\/p\u003e\u003cp\u003eSEBO shows the ET-2 cover at position 135 in its ET 1 \/ ET 2 diagram, recorded against heads built with the switch. Mechanically the shell is the molded top of the nozzle: it takes the fixings, holds the housing to shape, and seals the drive area from the dust the machine is picking up an inch below it. The failure is nearly always a split at a screw boss or a broken locating tab, and once either has happened the top stops pulling down flush and the crack keeps extending under vibration.\u003c\/p\u003e\u003cp\u003eThe replacement arrives as the cover only. Belt, roller, switch and fixings all transfer across from the head being repaired, so the job is a straight exchange with a screwdriver. If any of the original screws are chewed, SEBO lists them on their own, with screw 3.9 x 13 as 0102 singly and 0102ER in a ten pack, and locking washers as 0141 and 0141ER.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2341SWET, sold singly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e black, plain molding, no print\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-2 power heads with the switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 135, ET 1 \/ ET 2 power head sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied as:\u003c\/strong\u003e the cover only, with no internals\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrinted and colored alternatives:\u003c\/strong\u003e 2341WEET in white with the ET-2 print, 2341WESE as the other printed white shell, and 2341DRET in red\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA black SEBO ET-2 power head cover replacement is what this listing is, and the shells for the other head family, which look much the same in a photograph, carry entirely different numbers. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214503338234,"sku":"2341SWET","price":31.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/ec165901acfd0dcc40d56a1d1c8f33a9_96f785dc-eec3-408a-89ea-598a937c0868.jpg?v=1786670659"},{"product_id":"power-head-cover-for-et-2-with-et-2-print-white","title":"SEBO ET-2 Power Head Cover with ET-2 Print - White","description":"\u003cp\u003ePrinted with the ET-2 designation, this white shell is ordered as 2341WEET and belongs on ET-2 power heads built with the switch. The print is what separates it from the other white shells in the range, and it is the detail a photograph tends to lose.\u003c\/p\u003e\u003cp\u003eSEBO lists the cover at position 135 in its ET 1 \/ ET 2 diagram, a drawing that covers two head families on one sheet, so treat the sheet title as the name of a diagram and let the part number settle the fitment. The cover screws and clips down over the drive side of the nozzle, and it absorbs most of the knocks a head collects against furniture legs and baseboards. That is also why it is a wear item: the corners take the impacts, the fixing points take the vibration, and eventually one of them lets go. A head with a cracked cover no longer closes flat, which puts dust where the belt runs and lets the housing flex every time the machine is pushed.\u003c\/p\u003e\u003cp\u003eWhat arrives is the shell alone, so the roller, belt, switch and screws all carry over from the head being worked on. With the head open it costs nothing to check the belt for glazing and the bristle strip for wear before closing it back up, and if a screw is past reuse SEBO catalogs its hardware individually, listing screw 3.9 x 13 as 0102 and 0102ER for a ten pack.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2341WEET\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor and finish:\u003c\/strong\u003e white, with the ET-2 designation printed on the top face\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-2 power heads with the switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 135, ET 1 \/ ET 2 power head sheet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack:\u003c\/strong\u003e one cover, no internal components\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther white ET-2 shell:\u003c\/strong\u003e 2341WESE, which carries a different print on the same molding\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePlain ET-2 shells:\u003c\/strong\u003e 2341SWET in black, 2341DRET in red\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eAnyone searching for a genuine SEBO ET-2 power head cover in white, or an ET-2 nozzle top with the model name printed on it, wants this number. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214503371002,"sku":"2341WEET","price":31.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/88065e92e3fa55bd0a30c17ba3f37e6d.jpg?v=1786670662"},{"product_id":"power-head-cover-for-et-2-with-felix-print-white","title":"SEBO ET-2 Power Head Cover with FELIX Print - White","description":"\u003cp\u003eFELIX 2 Premium machines running the ET-2 head use this printed white shell, part 2341WESE. The FELIX name is printed across the top, so it is not a visual match for the plain or ET-2 marked versions even though the molding underneath is common to all of them.\u003c\/p\u003e\u003cp\u003eThe shell is the molded top of the power head. It holds the clip points and screw bosses that let the nozzle close flat while keeping dust off the drive underneath, and it is the surface that meets every baseboard and chair leg in the house. SEBO records it against ET-2 power heads built with the switch, so the switch variant is worth confirming before the order goes in. Replace the cover when a fixing point has cracked, when a corner has broken away, or when the top will not seat down square on the base any more; a shell that has lost its fit lets the housing flex and passes that movement into the belt path.\u003c\/p\u003e\u003cp\u003eIt is supplied bare. No belt, roller, switch or fixings are included, so those transfer from the head being repaired and the whole job comes down to a screwdriver and a few minutes. If a screw has stripped, SEBO lists its hardware on its own, with screw 3.9 x 13 as 0102 singly and 0102ER in a ten pack, and locking washers as 0141 and 0141ER.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2341WESE\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor and finish:\u003c\/strong\u003e white, wearing the FELIX print\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e the SEBO FELIX 2 Premium, and ET-2 power heads with the switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied as:\u003c\/strong\u003e the shell alone, without internal components\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrint differs from:\u003c\/strong\u003e 2341WEET, the white shell marked with the ET-2 designation\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePlain ET-2 shells:\u003c\/strong\u003e 2341SWET black, 2341DRET red\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eTypical searches that land here are FELIX 2 Premium power head cover and genuine SEBO ET-2 cover with FELIX print, and both describe this part. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214503502074,"sku":"2341WESE","price":31.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/a27c7a8726204332e9f5875c50a52323.jpg?v=1786669687"},{"product_id":"access-door-with-axle-and-spring-for-et-1-and-et-2-orange","title":"SEBO Access Door with Axle and Spring for ET-1 and ET-2 Power Heads \u0026mdash; Orange","description":"\u003cp\u003eET-1 and ET-2 power heads pass this hinged door on to every machine built around them, which is why one orange component covers so much of the SEBO range. Part 2909VO ships complete with its axle and spring, and SEBO puts it at position 108 on the ET-1\/ET-2, DART and FELIX parts sheets alike.\u003c\/p\u003e\u003cp\u003eThe door is what gets opened for belt and brush access, so its hinge sees more cycles than almost anything else on the head. As the spring slackens or the axle wears its bore oval, the door stops sitting flush: it hangs open a few millimetres, drags on carpet as the head is pulled back, rattles over hard floors, and eventually breaks at the pivot where the plastic has been working. Fitting the assembled part restores the pivot and the closing tension in one go, with no hardware to transfer across from a broken door and nothing to line up by hand.\u003c\/p\u003e\u003cp\u003eFull fitment runs to the SEBO ET-1 and ET-2 power heads in both the with-switch and without-switch versions, the FELIX Premium and FELIX 2 Premium, the DART, the AIRBELT D4 PREMIUM, the AIRBELT E3 Premium, the AIRBELT K3 PREMIUM and the C3.1. Behind the same door sit the parts most often replaced with it: toothed belt 2923, axle 2928, spring 2929 and orange foot pedal assembly 2937OR. Roller sizes split by head — the 12 inch 5010AM covers the ET-1 heads, FELIX Premium, DART, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1, while the ET-2 heads and the FELIX 2 Premium take the 15 inch 2838AM. Searches for a SEBO access door with its axle and spring fitted, an ET-1 belt door or a FELIX brush access door land here.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSEBO part 2909VO — hinged access door, axle and spring included\u003c\/li\u003e\n\u003cli\u003eFits: SEBO ET-1 and ET-2 power heads (with or without switch), FELIX Premium, FELIX 2 Premium, DART, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1\u003c\/li\u003e\n\u003cli\u003eColor: orange\u003c\/li\u003e\n\u003cli\u003eParts-diagram position: 108 on the ET-1\/ET-2, DART and FELIX sheets\u003c\/li\u003e\n\u003cli\u003eTypical symptom: a door that will not latch flush, drags on carpet, or has snapped at the hinge\u003c\/li\u003e\n\u003cli\u003eRelated part numbers: 2923 belt, 2928 axle, 2929 spring, 2937OR foot pedal with axle and spring\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine SEBO\u003c\/strong\u003e; ships in 2–5 business days\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214507041018,"sku":"2909VO","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2909VO_bbb0cc33-49e9-460f-8834-32029ed2e7b1.jpg?v=1785150214"},{"product_id":"chassis-for-et-2-gray-black","title":"SEBO ET-2 Power Head Chassis — Gray Black","description":"\u003cp\u003ePart 2325GS is the gray black chassis built for the ET-2 head, the moulded base that the motor, roll bearings and wheels all mount into. It is specific to the ET-2, which is the wider of the two power head families, so confirm the head designation on your own machine before ordering rather than matching by outline.\u003c\/p\u003e\u003cp\u003eDamage at this level is nearly always physical: a drop down a stair, a crack running out from a screw boss, a wheel mount that no longer holds its position. What sends people looking for a frame is usually a repair that refused to take. Bearings replaced and the roll still runs noisy, a new belt that keeps walking off its pulley, a sole plate that will not pull up flush at one corner. All three trace back to a frame that has lost its geometry, and none of them respond to another round of wear parts. SEBO lists the ET-2 chassis at position 100 in the ET 1 \/ ET 2 power head diagram.\u003c\/p\u003e\u003cp\u003eThe frame is supplied on its own, so the motor, bearing blocks, wheels, pulley and height linkage all move across from the old one. Keep the fasteners grouped by location as they come out, and take the opportunity to renew anything already close to the end of its life while access is unusually good. The equivalent frame for the narrower ET-1 head is 2324GS in the same finish, and the light gray ET-1 version is 2324HG. Set the new frame down on a flat surface before building it up and confirm it sits without a rock, which is the simplest check that the replacement is true.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX 2 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-2 power heads built with or without an on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 2325GS\u003c\/li\u003e\n\u003cli\u003eColour: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 100, ET 1 \/ ET 2 power head parts list\u003c\/li\u003e\n\u003cli\u003eSupplied as the bare frame; original internals transfer across\u003c\/li\u003e\n\u003cli\u003eCarries the motor mounting, bearing seats and wheel locations\u003c\/li\u003e\n\u003cli\u003eRelated number: 2324GS, the ET-1 chassis\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO part. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214510579962,"sku":"2325GS","price":31.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/93436893dabbdd75636d4b4a5db5a352.jpg?v=1786669684"},{"product_id":"back-cover-ts-neck-for-et-1-et-2-felix-except-white-and-disco-gray-black","title":"SEBO Back Cover for the TS-Neck \u0026mdash; FELIX, ET-1, ET-2 and DISCO, Gray Black","description":"\u003cp\u003eBehind the TS-neck joint sits a molded panel that caps the back of the head. Part 2947GS is that panel in gray black, shaped to the housing contour and drilled for the original screws, so the head goes back together without packing or shimming anything into place.\u003c\/p\u003e\u003cp\u003eSEBO's power head diagram numbers the cover 115, and the FELIX sheet uses the same number, immediately after the swivel neck wiring at 114 and just before the metal segment set at 116. Panels crack where they get gripped during a wand change, or when the head is tipped hard against a stair nose. Once broken, the opening lets dust reach the neck hardware and the joint loses some of its stiffness, so the head feels less planted underfoot. Replacing the cover is a screwdriver job with the head on the bench, and it is the right moment to look at the segments and slide inside the same joint.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2947GS, TS-neck back cover\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched, and the DISCO floor polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 115 on the power head and FELIX sheets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther finish:\u003c\/strong\u003e light gray panel 2947HG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 0876ER swivel neck wiring at 114, 2950ER segment set at 116, 2945GS slide at 119\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting tip:\u003c\/strong\u003e photograph the screw layout before the old panel comes off\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA genuine SEBO TS-neck cover keeps the dust out of the joint it protects, which is the whole reason to fit the correct moulding rather than tape over a split. Factory SEBO part supplied by an authorized dealer, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214514970874,"sku":"2947GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0ef463bbc1139d200d413b609783f585.jpg?v=1786668920"},{"product_id":"release-button-cover-for-et-1-et-2-felix-swivel-neck-2307gs-and-disco-gray-black","title":"SEBO Release Button Cover for FELIX, ET-1, ET-2 and DISCO Swivel Necks \u0026mdash; Gray Black","description":"\u003cp\u003eEvery time the handle is reclined, a thumb lands on the neck release button and on the cap that covers it. Part 2952GS is that cap in gray black, giving the button a defined face to press and keeping the mechanism beneath it sealed away from dust.\u003c\/p\u003e\u003cp\u003eSEBO numbers the button cover 118 on the ET-1\/ET-2 power head diagram and 118 again on the FELIX sheet, immediately after the release button and its leaf spring at 117. When the cap splits or works its way loose, the release starts to feel vague: you press, nothing obvious happens, and the handle only drops on the second or third attempt. If a new cap does not restore a crisp action, the button assembly itself is the next item to check, listed in gray black as 1737GS, and the complete gray black swivel neck it all mounts into is 2307GS.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2952GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched, and the DISCO floor polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNeck reference:\u003c\/strong\u003e used on swivel neck 2307GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 118 on the power head and FELIX sheets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther finish:\u003c\/strong\u003e light gray cap 2952HG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 1737GS release button with leaf spring, 2951GS socket cover, 2945GS slide\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eSmall parts like this decide how a machine feels in the hand, and a sound cap is the difference between a handle that releases on the first press and one that has to be worked at. Order by finish rather than by shape, since the light gray cap fits the same button but sits obviously wrong against darker trim. Authorized SEBO dealer stock, packed and shipped in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214525653242,"sku":"2952GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/92dff885fa0a839dc6919563415f13e0.jpg?v=1786668936"},{"product_id":"socket-cover-ts-neck-for-et-1-et-2-felix-except-white-and-disco-gray-black","title":"SEBO TS-Neck Socket Cover for FELIX, ET-1, ET-2 and DISCO \u0026mdash; Gray Black","description":"\u003cp\u003ePower reaches the brush motor through contacts in the neck, and 2951GS is the gray black cap that closes over them. It keeps carpet fluff and grit off the connection point where the power head joins the machine, in a spot that sits low down and collects everything the floor has to offer.\u003c\/p\u003e\u003cp\u003eSEBO places the socket cover at position 120 on both the ET-1\/ET-2 power head diagram and the FELIX sheet, next along from the swivel neck slide at 119. A cracked or absent cap tends to announce itself electrically rather than visually: the brush roll cuts in and out as the neck flexes, because nothing is holding the connection square any more. Unplug the machine at the outlet before opening the neck, and check the swivel neck wiring, part 0876ER, for chafing while the contacts are exposed.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2951GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched, and the DISCO floor polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 120 on the power head and FELIX sheets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther finish:\u003c\/strong\u003e light gray cap 2951HG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 0876ER swivel neck wiring, 2945GS slide, 2952GS release button cover, 2947GS back cover\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSafety step:\u003c\/strong\u003e disconnect from the outlet before working on the neck\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eAn intermittent brush roll is one of the more frustrating faults to chase on a SEBO ET-1, and a missing socket cover is among the first causes worth ruling out before anything electrical is condemned. Genuine SEBO part, authorized dealer stock, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214526013690,"sku":"2951GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/f79c4382de9b7ab7eece7ba8e5737685.jpg?v=1786668928"},{"product_id":"lens-left-without-on-off-switch-for-et-1-and-et-2","title":"SEBO Left Lens for ET-1 and ET-2 Power Heads — Switchless Version","description":"\u003cp\u003eClouded or cracked, a lens is a cosmetic fault that also lets grit reach the front of the nozzle. SKU 20955 is the left-hand lens moulded for the ET-1 and ET-2 power head families in the configuration supplied with no on\/off rocker, and it covers the light aperture at the leading corner of the head.\u003c\/p\u003e\u003cp\u003eTwo details decide whether this is the right ordering choice. The first is side: left and right lenses carry separate part numbers and do not interchange, so set the head down on its sole plate, look at it from the operating position, and work out which corner you are replacing before ordering. The second is switch layout, because heads built with an on\/off rocker use different front mouldings and a lens lifted from one will not seat properly in the other. Get either wrong and the new part sits proud of its recess instead of clipping flush, which puts it straight back in the firing line of the next chair leg.\u003c\/p\u003e\u003cp\u003eReplacement is usually prompted by a lens gone milky enough to dim the light it sits over, one starred by an impact, or one that has lost a retaining tab and keeps working its way out on corners. Fitting it into a clean recess matters more than it sounds, since grit trapped behind the moulding will crack the next one just as quickly. SEBO also lists this lens against the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium, all of which are supplied with power heads from the same families, so canister owners can order the same number with confidence.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits ET-1 and ET-2 power heads supplied with no on\/off rocker\u003c\/li\u003e\n\u003cli\u003ePart number: 20955\u003c\/li\u003e\n\u003cli\u003eAlso listed by SEBO for the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eLeft-hand side; the right-hand lens is a separate number\u003c\/li\u003e\n\u003cli\u003eClear moulded lens, genuine SEBO\u003c\/li\u003e\n\u003cli\u003eSold individually\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eShips in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214528307450,"sku":"20955","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/ea22de16f3c40a252791f6381e55bf41.jpg?v=1786670157"},{"product_id":"on-off-button-lens-for-et-1-and-et-2","title":"SEBO On\/Off Button Lens for Switched ET-1 and ET-2 Power Heads","description":"\u003cp\u003eSwitched power heads carry a small moulded lens over the on\/off control. Part 2957 is that piece: the face your thumb presses and the cover that keeps carpet dust away from the switch sitting behind it.\u003c\/p\u003e\u003cp\u003eSEBO lists it at position 139 on the ET-1\/ET-2 power head diagram, where it is noted as the left hand item, at 139 on the FELIX sheet and at 136 on the DART. Yellowing, a star crack across the face, or a lens that has popped out and vanished under the sofa are the reasons this part gets ordered. Because the lens is only a cover, it is worth confirming that the switch itself still operates cleanly while the head is open: the single pole switch is 05114, the lever and leaf spring behind it are 2958ER, and SEBO sells the whole switch group built up as 2959ER if the fault turns out to be electrical rather than cosmetic.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2957\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads built with the on\/off switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 139 on the power head and FELIX sheets, 136 on the DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e button face and dust cover for the head's on\/off switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2956 brush light lens at 140, 05114 switch, 2958ER lever with leaf spring, 2959ER complete switch assembly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCheck first:\u003c\/strong\u003e confirm the switch still latches before blaming the lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eUnswitched heads have no lens to lose, so check which build you have before ordering a SEBO ET-1 on\/off button lens. The brush light lens on the other side of the head is 2956, a different moulding at the next position along, and the two are easy to confuse when working from the drawing rather than the number. Genuine SEBO stock from an authorized dealer; ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214528340218,"sku":"2957","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/c4e52fcde7b157052422e5b0922e5a20.jpg?v=1786668948"},{"product_id":"lens-right-brush-light-for-et-1-and-et-2","title":"SEBO Brush Light Lens, Right Hand, for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eClear plastic keeps grit off the brush light while letting the beam through, and 2956 is the right hand lens for that duty. It seats in the power head housing over the lamp, taking the scuffs and knocks that come from working tight against baseboards, table legs and stair risers.\u003c\/p\u003e\u003cp\u003eSEBO catalogues the right hand lens at position 140 on the ET-1\/ET-2 diagram, at 140 on the FELIX sheet and at 137 on the DART, immediately alongside the on\/off button lens. Lenses cloud with age and crack on impact, and a hazed lens dims the light long before the lamp behind it gives up, which is why a machine that seems to have lost its brush light often only needs the plastic changed. Wipe out the lamp recess while the lens is off the head, and check the seat for old grit so the new lens sits flush rather than proud.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2956, right hand lens\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 140 on the power head and FELIX sheets, 137 on the DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e protects and covers the brush light in the head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2957 on\/off button lens at 139, 2684ER printed circuit board\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTip:\u003c\/strong\u003e clean the lamp recess before the new lens goes in\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eBuyers hunting a SEBO ET-2 brush light lens replacement should note the handing: this is the right hand moulding, and the switch lens on the other side of the head is a separate number entirely. Both sit within one position of each other on the same diagram, so it is easy to order the wrong one from a drawing alone. Genuine SEBO lens supplied through an authorized dealer, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214528372986,"sku":"2956","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2956_411f9f5a-468b-4659-aca8-e6fd83aa6b4e.jpg?v=1785142869"},{"product_id":"foot-pedal-with-axle-and-spring-for-et-1-et-2-and-disco-orange","title":"SEBO Foot Pedal with Axle and Spring for FELIX, ET-1, ET-2 and DISCO \u0026mdash; Orange","description":"\u003cp\u003eOrange plastic, a steel pivot pin and a return spring arrive together as one item in 2937OR. Step on the pedal and the handle unlocks from upright so the machine can be reclined for a pass under a table; lift your foot and the spring carries the pedal back, ready for the next release.\u003c\/p\u003e\u003cp\u003eSEBO draws the pedal at position 112 on the ET-1\/ET-2 power head sheet, at 112 on the DART diagram and at 112 on the FELIX diagram, with the wheel at 111 on one side of it and the complete swivel neck at 113 on the other. The DISCO floor polisher parts list carries the same pedal at position 24. Fit a new one when the handle drops loose the moment the pedal is brushed, when the pedal stays down after being pressed, or when a snapped spring leaves the lock rattling as you push. Since the pin and spring come in the pack, nothing has to be salvaged off the old assembly.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2937OR\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied as:\u003c\/strong\u003e pedal, axle and return spring together\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e orange\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched, and the DISCO floor polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 112 on the power head, DART and FELIX sheets; 24 on the DISCO list\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2306GS wheel at 111, 2307GS complete swivel neck at 113\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis is one of the most-searched SEBO FELIX pedal repairs for a reason: the pedal takes a boot every time the machine is used, and it is the part that decides whether the handle release still feels positive. German-made SEBO component from an authorized dealer, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214528733434,"sku":"2937OR","price":10.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2937OR_efad1f05-495b-44c7-8c75-1a58885a96c8.jpg?v=1785139812"},{"product_id":"bearing-segments-metal-ts-neck-for-all-et-1-et-2-and-disco-swivel-necks-6-pc-set","title":"SEBO Metal Bearing Segments for the TS-Neck Swivel \u0026mdash; 6 Piece Set","description":"\u003cp\u003eSix machined metal segments carry the load inside a SEBO TS-neck swivel, and 2950ER supplies the full set. They ring the joint between power head and neck, spreading steering forces so the head turns on metal instead of grinding plastic against plastic.\u003c\/p\u003e\u003cp\u003eSEBO shows the segments as a six-piece set at position 116 on the ET-1\/ET-2 power head diagram and at 116 on the FELIX sheet, with the DISCO floor polisher list carrying them at position 7. Change all six together. Mixing tired segments with new ones loads the joint unevenly, and the swivel keeps the notchy, sloppy feel that sent you looking for this part in the first place. The two neighbours on the same diagram wear at a similar rate, so pull the slide 2945GS at position 119 and the swivel neck bearing 2954 at 122 while the joint is open and judge all three together.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2950ER\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack:\u003c\/strong\u003e six metal segments, sold as one complete set\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e metal, for the TS-neck swivel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e the TS-neck swivel on ET-1 and ET-2 power heads, switched and unswitched, and on the DISCO floor polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 116 on the power head and FELIX sheets, 7 on the DISCO list\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2945GS and 2945HG slides, 2954 neck bearing, 2947GS back cover\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eOf every part in a SEBO ET-1 or ET-2 swivel neck rebuild, this set does the most to bring back a tight, quiet joint, because it is the metal that actually takes the steering load rather than the plastic wrapped around it. Fitting the set is a strip-and-rebuild of the neck, so it is worth ordering everything the joint needs in one go. Authorized SEBO dealer supply, out the door in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214531027194,"sku":"2950ER","price":14.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/efa97c3bba2028741c79821e4c216750.jpg?v=1786668925"},{"product_id":"lever-with-leaf-spring-for-et-1-and-et-2","title":"SEBO Switch Lever with Leaf Spring for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eBetween your thumb and the electrical contacts sits a lever backed by a leaf spring, and 2958ER supplies both as one piece. The spring gives the on\/off action its snap and returns the lever to rest after each press, so the control commits to on or to off rather than hovering somewhere between the two.\u003c\/p\u003e\u003cp\u003eSEBO draws the lever at position 131 on the ET-1\/ET-2 power head sheet, at 131 on the FELIX diagram and at 139 on the DART, where it sits with the single pole switch 05114 and the wire 0881 in the group that makes up the complete switch. A tired or broken spring shows up as a mushy button, a lever that stays pushed in, or a brush roll that shuts itself off when the head takes a knock against a chair leg. The lever is also supplied inside the built-up assembly 2959ER, which is the better choice when the switch body or its wiring has failed as well.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2958ER, lever and leaf spring together\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 131 on the power head and FELIX sheets, 139 on the DART\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e gives the on\/off control its travel, snap and return\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2959ER complete switch assembly, 05114 single pole switch, 0881 wire to the board, 2957 button lens\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eWhen a SEBO ET-1 switch feels dead under the thumb but the machine still runs, the lever and its spring are the parts to look at before anything electrical gets condemned, and they are far less work to change than the board behind them. Genuine SEBO parts, authorized dealer supply, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214532763898,"sku":"2958ER","price":8.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2958ER.jpg?v=1785151879"},{"product_id":"swivel-neck-slide-for-et-1-et-2-felix-except-white-and-disco-gray-black","title":"SEBO Swivel Neck Slide for FELIX, ET-1, ET-2 and DISCO \u0026mdash; Gray Black","description":"\u003cp\u003eSteering feel comes from the swivel neck, and the slide is the piece that guides it. Finished in gray black, 2945GS rides in the neck joint linking head to handle, holding the pivot on a controlled path as the machine is swept left and right along a wall.\u003c\/p\u003e\u003cp\u003eSEBO draws this slide at position 119 on the ET-1\/ET-2 power head sheet and at the same number on the FELIX diagram, one place after the button cover at 118 and one before the socket cover at 120. A slide worn thin lets the neck feel loose and vague; one that has scored or picked up grit makes the head fight every change of direction. Either symptom points straight at this part. While the joint is apart it is worth checking the two components that share the load with it: the six-piece metal segment set 2950ER at position 116 and the swivel neck bearing 2954 at 122. If the neck itself is cracked rather than merely worn, the complete gray black assembly is 2307GS at 113.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2945GS\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e gray black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched, and the DISCO floor polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 119 on the power head and FELIX sheets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish check:\u003c\/strong\u003e the light gray equivalent is stocked separately as 2945HG\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2950ER segment set, 2954 neck bearing, 2947GS back cover, 2951GS socket cover\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eSearches for a SEBO ET-2 swivel neck repair usually end at one of three parts, and the slide is the one to rule out before committing to a full rebuild of the joint. Authorized SEBO dealer stock, dispatched in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214533714170,"sku":"2945GS","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0d89380aa5368074327b0d406778b531.jpg?v=1786668915"},{"product_id":"screw-f-3-9-x-21-din-968-single-for-et-1-and-et-2","title":"SEBO Screw F 3.9 x 21 (DIN 968) for ET-1 and ET-2 Power Heads","description":"\u003cp\u003ePower heads take more punishment than the machines they hang off, with the brush roll spinning inches away and every joint shaken constantly. The F 3.9 x 21 to DIN 968 is the long screw holding that housing together on SEBO's ET-1 and ET-2. DIN 968 describes a cross-recessed pan head tapping screw with a collar, meaning a built-in flange under the head that spreads the clamping load over a wider ring of plastic than a plain pan head manages.\u003c\/p\u003e\u003cp\u003eThat flange is the reason the standard is used here. On a component that vibrates continuously, a screw head bearing on a small area works its way into the moulding until the joint has play in it again. The collar keeps the pressure spread and the joint tight for far longer.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 1020\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO power heads ET-1 and ET-2\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpecification:\u003c\/strong\u003e F 3.9 x 21 to DIN 968\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead and drive:\u003c\/strong\u003e cross-recessed pan head with collar\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 3.9 mm diameter, 21 mm long\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSold:\u003c\/strong\u003e each\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShorter DIN 968 screw:\u003c\/strong\u003e part 1021 at 13 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eAt 21 mm it is noticeably deeper than the 13 mm DIN 968 screw used elsewhere on the same head, and the two are easy to confuse once they are out of the casing. Put the short one where the long one belongs and the joint is only half clamped, which turns up later as a creak, a gap along the seam, or a brush housing that no longer holds its alignment.\u003c\/p\u003e\u003cp\u003eReplace one when the recess has rounded, when it no longer draws the casing halves together, or when the original was lost during a belt or brush roll service. Unplug the machine before opening a power head and keep the screws laid out in the order they came off, because lengths are mixed within a single casing.\u003c\/p\u003e\u003cp\u003eSearches for a SEBO ET-1 housing screw, a SEBO ET-2 power head fastener or a DIN 968 3.9 x 21 replacement all point here. Genuine SEBO hardware supplied by an authorized dealer, with dispatch in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214535418106,"sku":"1020","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/01020.jpg?v=1709348801"},{"product_id":"screw-f-3-9-x-13-din-968-single-for-et-1-et-2-and-softcase","title":"SEBO Screw F 3.9 x 13 (DIN 968) for ET-1, ET-2 and SOFTCASE","description":"\u003cp\u003eTwo DIN 968 screws share the ET parts list and the difference between them is eight millimetres of thread. This is the 13 mm one, part 1021, fitted on the ET-1 and ET-2 power heads and on the SOFTCASE. Both carry the collared cross-recessed pan head that the standard defines, a flange under the head that widens the bearing surface so the screw does not sink into the plastic under vibration.\u003c\/p\u003e\u003cp\u003eBecause that head form matches its longer relative exactly, these two get mixed up on the bench more often than any other pair in the box. The giveaway comes on final tightening: the right screw pulls the joint flat and stops, the wrong one either bottoms out early or spins on in a hole it was never meant to reach.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 1021\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-1, ET-2 and SOFTCASE\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpecification:\u003c\/strong\u003e F 3.9 x 13 to DIN 968\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead and drive:\u003c\/strong\u003e cross-recessed pan head with collar\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e 3.9 mm diameter, 13 mm long\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSold:\u003c\/strong\u003e each\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLonger DIN 968 screw:\u003c\/strong\u003e part 1020 at 21 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eChange one when the head has rounded out under a slipping driver, when the screw turns without clamping, or when a strip-down has left a casing screw missing. Keep a couple spare if you service ET heads regularly, as these are the ones that roll off a bench and disappear into a workshop floor.\u003c\/p\u003e\u003cp\u003eA power head lives a harder life than the machine it hangs from. The brush roll runs inches away from every fastener in the casing, and the vibration that carries into the joints never stops while the machine is switched on. That is the reason SEBO specifies a collared screw here rather than a plain pan head, and the reason a casing screw is worth replacing rather than reusing once its recess has started to open up.\u003c\/p\u003e\u003cp\u003eAnyone looking for a SEBO ET-2 casing screw, a SOFTCASE body screw or a genuine SEBO DIN 968 3.9 x 13 replacement wants this part number rather than the 21 mm version. Hold the old screw against the specification above before ordering. Genuine SEBO fastener from an authorized dealer, shipping in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214535450874,"sku":"1021","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/01021.jpg?v=1709348798"},{"product_id":"screw-am4-x-30-din-7985-single-for-x-g-series-370-comfort-300-350-et-1-et-2-and-duo","title":"SEBO AM4 x 30 Screw, DIN 7985, for X and G Series, 370 COMFORT, 300\/350, ET-1, ET-2 and DUO","description":"\u003cp\u003eAt 30 mm this is the long one. Part 176, an AM4 x 30 screw to DIN 7985, reaches deep through the housing on SEBO's X-series and G-series machines, on the 370 COMFORT, on the 300 and the 350, on the ET-1 and ET-2 power heads, and on the DUO. It is sold individually.\u003c\/p\u003e\u003cp\u003eDIN 7985 is the pan-head cross-recess standard, so the head sits proud and takes a Phillips driver. The reason to order by the full designation is that several M4 screws of different lengths appear on the same machine, often within a few centimetres of each other, and they are not interchangeable — a shorter screw in this hole simply will not reach the material it is meant to be pulling together.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO X series, G series, 370 COMFORT, 300 and 350, the ET-1 and ET-2 power heads, and the DUO\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSize:\u003c\/strong\u003e AM4 x 30\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStandard:\u003c\/strong\u003e DIN 7985\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack:\u003c\/strong\u003e sold individually\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOrder as:\u003c\/strong\u003e SEBO part 176\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eDeep fastenings such as this one carry more of the clamping load than the short screws around them. Strip the thread here and you are left with an assembly that never quite pulls together no matter how hard everything else is tightened, usually announced by a creak when the machine is picked up or a seam you can open with a thumbnail. If the boss itself has broken up rather than the screw, fitting a new screw alone will not cure it.\u003c\/p\u003e\u003cp\u003eOne designation covering this many machines is a consequence of SEBO reusing a small set of fasteners across the range, which is convenient if you are stocking a workshop drawer rather than repairing a single vacuum. A few spares ordered alongside the part you actually came for are rarely wasted.\u003c\/p\u003e\u003cp\u003eSearches for a SEBO X series screw, an ET-2 housing screw or DIN 7985 M4 x 30 all point here. Keep the old screw for comparison, and note where each length came from before the parts tray gets mixed. Genuine SEBO hardware from an authorized dealer.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214537253114,"sku":"176","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0176.jpg?v=1709348766"},{"product_id":"spring-for-axle-adjustment-assembly-for-et-1-and-et-2","title":"SEBO Spring for the Axle Adjustment Assembly \u0026mdash; ET-1 and ET-2 Power Heads","description":"\u003cp\u003eA height setting only holds because a spring is holding it. Part 2929 is that spring inside the axle adjustment assembly of the ET-1 and ET-2 power heads, catalogued at position 106 on SEBO's ET-1\/ET-2, DART and FELIX sheets, immediately ahead of the complete pile adjustment assembly at 107 and the selector knob at 110.\u003c\/p\u003e\u003cp\u003eAs the spring weakens, the head stops keeping the height it was given. Brush contact turns uneven, one setting drags on plush carpet while the next barely reaches the fibers, and the selector loses the crisp step from one position to the next. Because the part is buried in the adjustment group, it is usually renewed while the head is already stripped on the bench, alongside whichever selector knob the machine carries: 2931GS in gray black, 2931HG in light gray, 2931SB in silver. Where the whole group is tired rather than just the spring, SEBO sells the assembly complete as 2316GS or, for light gray machines, 2316HG.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2929, single spring\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, with or without the on\/off switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 106 on the ET-1\/ET-2, DART and FELIX lists\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e holds tension in the axle adjustment mechanism that sets brush height\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2316GS and 2316HG pile adjustment assemblies, 2931GS, 2931HG and 2931SB knobs\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTypical symptom:\u003c\/strong\u003e a carpet height setting that will not stay where it is put\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eAnyone searching for a SEBO ET-1 height adjustment spring is usually chasing that one fault, and this is the smallest part in the group capable of causing it, so it is the sensible place to start. Genuine SEBO component supplied by an authorized dealer, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214540890362,"sku":"2929","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/ef2faebb8522a36290cbd8c73a909dc9.jpg?v=1786668898"},{"product_id":"wire-tie-short-for-x1-x2-x4-x5-g-series-and-et-2","title":"SEBO Short Wire Tie for AUTOMATIC X, ESSENTIAL G, FELIX 2 and ET-2 Power Heads","description":"\u003cp\u003eOf the two internal wire ties SEBO stocks, 5401 is the shorter one. The ESSENTIAL G4\/G5 drawing lists it at item 143 as the outer tie under the bottom plate, and SEBO's ET power head sheet carries it at item 137 in the same outer position.\u003c\/p\u003e\u003cp\u003eThose two references say most of what needs saying about where it lives. This is the tie that gathers the loom running along the underside of a machine or through a power head and holds it away from the brush roll, the drive and everything else down there that turns. On the power head sheet it sits within a few positions of the motor pulley and the switch assembly, which is exactly the area where loose wiring has somewhere dangerous to go.\u003c\/p\u003e\u003cp\u003eTies get cut to reach something during a repair and are then easy to overlook when the machine goes back together. A loom left unsecured does not fail immediately; it drifts, finds a moving part or a hot surface, and shows up months later as a chafed lead. Length matters as much as presence: the longer tie leaves slack where this shorter one pulls the bundle in properly, so use the number the diagram specifies for the position rather than whichever one is in the drawer. The long version is 5402.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO AUTOMATIC X2 and X5; SEBO ESSENTIAL G1, G2, G4 and G5; SEBO FELIX 2 Premium; SEBO ET-2 power heads, switched and unswitched\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength:\u003c\/strong\u003e short tie\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 5401\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e item 143 outer, bottom plate, ESSENTIAL G4\/G5; item 137 outer, ET power heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction:\u003c\/strong\u003e secures internal wiring clear of moving parts\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLong version:\u003c\/strong\u003e 5402\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eFit it in the position the drawing shows rather than wherever there is room, since the routing is what keeps the loom out of trouble in the first place. Genuine SEBO wire tie, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214542987514,"sku":"5401","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/5401.jpg?v=1785150534"},{"product_id":"brush-motor-120v-200w-with-pulley-for-et-2","title":"SEBO 200 W Brush Motor with Pulley for ET-2 Power Heads","description":"\u003cp\u003eThe 200 watt brush motor is the ET-2 specific unit, and 2974ER is it: 120 volts, pulley fitted, ready to drop straight into the head. That higher rating is what separates it from the 175 watt motor, part 2973ER, so identify the head before ordering rather than treating the two as interchangeable — they share a diagram position but not a part number.\u003c\/p\u003e\u003cp\u003eFitment is short and precise. SEBO lists 2974ER for ET-2 power heads in both the switched and unswitched builds, and for the FELIX 2 Premium upright that carries an ET-2 head. On the power head parts diagram the motor sits at position 128 and is listed together with items 129 and 139, so what arrives is the drive assembly rather than a bare armature.\u003c\/p\u003e\u003cp\u003eReplace it when the brush roll turns slowly or stops while suction stays strong, when dry bearings set up a squeal that rises with speed, or when a burnt smell follows the head down the hallway. A motor that has begun to drag will also chew through belts, so a machine on its second or third belt in quick succession is worth a closer look at the drive rather than another belt. Two cheaper faults mimic a dead motor and should be ruled out first: the carbon brush set 05141S, and the 200 W printed circuit board 2689ER. With the head open, the belt 2923, the motor pulley 2319, the 15 in brush roller 2838AM and the bearing blocks 2313GS and 2314GS are all within reach for inspection.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2974ER\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRating:\u003c\/strong\u003e 120 V, 200 W\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied:\u003c\/strong\u003e with pulley\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-2 power heads, switched and unswitched, and the FELIX 2 Premium\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 128, listed with 129 and 139\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated numbers:\u003c\/strong\u003e 05141S carbon brush set, 2689ER circuit board, 2923 belt, 2319 motor pulley, 2838AM brush roller\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNot to be confused with:\u003c\/strong\u003e the 175 W brush motor, part 2973ER\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eSearches for a SEBO ET-2 brush motor, a 200 W power head motor replacement or part 2974ER all point at this unit. Genuine SEBO drive motor from an authorized dealer. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214545346810,"sku":"2974ER","price":98.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/51746a1a2515aa10f8356294e6cbe34f.jpg?v=1786669693"},{"product_id":"carbon-brush-set-for-et-1-and-370-comfort-power-head-2973er-et-2-2974er-and-disco-3252er","title":"SEBO Carbon Brush Set for ET-1, ET-2 and DISCO Power Head Motors","description":"\u003cp\u003eRoller stopped, suction unaffected. That combination points at the power head motor rather than anything in the airway, and part 05141S is the carbon set that serves it. SEBO uses the same set across three motors: the 2973ER in the ET-1 and the 370 COMFORT power head, the 2974ER in the ET-2, and the 3252ER in the DISCO polisher.\u003c\/p\u003e\u003cp\u003eBrush motor carbons wear more slowly than the pair in a suction motor, since the agitator only draws current while the head is running, but the end state is identical. The roller becomes reluctant to start, stalls when it meets thick pile, comes back if the machine is rocked, and finally does nothing at all. Fits the ET-1 and ET-2 power heads in both switched and unswitched builds, the DISCO Floor Polisher, the 370 COMFORT, and the machines these heads are supplied on — FELIX Premium, FELIX 2 Premium, DART, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and the C3.1.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e SEBO 05141S, carbon brush set\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMotors:\u003c\/strong\u003e 2973ER, 2974ER and 3252ER\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 129 on the SEBO ET 1 \/ ET 2, DART and FELIX sheets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSuction motor instead:\u003c\/strong\u003e the FELIX and DART fan motor takes 05140S\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRule out first:\u003c\/strong\u003e a broken belt, a roller bound with hair, or a failed switch such as 05114\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplace when:\u003c\/strong\u003e the roller is slow to start, stalls in thick pile, or stops while airflow through the hose is unchanged\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMachines these heads ship on:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, AIRBELT D4 PREMIUM, AIRBELT E3 Premium, AIRBELT K3 PREMIUM and C3.1\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eCheck that the roller spins freely by hand before the head goes back together, so the new carbons are not put straight to work against a jam that will wear them out again. Genuine SEBO carbons for an ET-1 or ET-2 power head, ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214545707258,"sku":"05141S","price":14.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/05141S.jpg?v=1785148938"},{"product_id":"motor-pulley-for-et-1-et-2-and-370-comfort","title":"SEBO Motor Pulley for ET-1, ET-2 and 370 COMFORT Power Heads","description":"\u003cp\u003eDrive reaches the brush roll through a small pulley on the motor shaft, and 2319 is that pulley. Once the groove polishes smooth or the hub loses its grip on the shaft, the belt begins slipping under load: brush speed falls away the moment the head meets carpet, and belts start wearing out sooner than they should.\u003c\/p\u003e\u003cp\u003eSEBO places it at position 138 in the ET 1 \/ ET 2 and FELIX diagrams, and at position 135 in the DART diagram. The symptoms are easy to confuse with a stretched belt, which is why the pulley is so often overlooked. The distinguishing signs are a bright, mirror-polished groove where the surface should still have some texture, black belt dust packed around the motor mount, and a fresh belt that starts slipping again within weeks of being fitted. A pulley turning on its shaft rather than with it is the clearest case of all, and it usually announces itself as a brush roll that stops under load while the motor keeps running.\u003c\/p\u003e\u003cp\u003eThis is worth renewing while a head is already stripped for a belt or bearing job, since the access is the same and a worn pulley will chew through a new belt. Fitment is broad: the SEBO FELIX Premium, FELIX 2 Premium, DART, 370 COMFORT and C3.1 along with the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium, covering ET-1 and ET-2 power heads in switched and unswitched form.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, FELIX 2 Premium, DART, 370 COMFORT, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 as well as ET-2 power heads, switched or unswitched\u003c\/li\u003e\n\u003cli\u003ePart number: 2319\u003c\/li\u003e\n\u003cli\u003eMotor pulley for the brush roll drive\u003c\/li\u003e\n\u003cli\u003eDiagram positions: 138 in the ET 1 \/ ET 2 and FELIX lists, 135 in the DART list\u003c\/li\u003e\n\u003cli\u003eWorth fitting at the same time as a fresh belt\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO part. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214545903866,"sku":"2319","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2319_83ff1ce9-4af2-4d49-b0e0-a5dac11dd070.jpg?v=1785163589"},{"product_id":"printed-circuit-board-200w-for-et-2-power-head-new-version-with-yellow-on-off-light","title":"SEBO 200W Printed Circuit Board for ET-2 Power Heads","description":"\u003cp\u003eRated at 200W and carrying the yellow on\/off lamp, part 2689ER is SEBO's later control board for the ET-2 power head. It sits at position 134 in the ET 1, ET 2 Power Heads parts diagram.\u003c\/p\u003e\u003cp\u003eSwitching and speed control for the head both run through this board, so a failure here stops the roller dead while the suction motor carries on exactly as normal. That split, good airflow at the nozzle but a brushroll that is dead or comes and goes, is the usual reason one gets ordered. A snapped belt produces a very similar complaint, so it is worth lifting the base plate and confirming the belt and roller are sound before spending money on electronics.\u003c\/p\u003e\u003cp\u003eFitment covers ET-2 Power Heads (with switch) and ET-2 Power Heads (without switch), and the board is also used on the SEBO FELIX 2 Premium. Match the wattage carefully: the 175W board is a different part with its own number, 2684ER, and the two are not interchangeable, so read the rating off the board that comes out before ordering.\u003c\/p\u003e\u003cp\u003eLabel each connector as it comes away so the new board wires back exactly as the old one did, keep it dry and away from static, and hold it by the edges. Anyone searching for a SEBO ET-2 circuit board, a 200W power head board, or a FELIX 2 Premium controller replacement is looking at this number.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO ET-2 power heads, with or without a switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso fits:\u003c\/strong\u003e FELIX 2 Premium\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRating:\u003c\/strong\u003e 200W\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVersion:\u003c\/strong\u003e later board with the yellow on\/off lamp\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2689ER\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 134 in SEBO's ET 1, ET 2 Power Heads diagram\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDo not substitute:\u003c\/strong\u003e the 175W board, 2684ER\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO board from an authorized dealer. Ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214547902714,"sku":"2689ER","price":48.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2689ER.jpg?v=1785153424"},{"product_id":"switch-single-pol-for-et-1-and-et-2","title":"SEBO Single-Pole Switch for ET-1 and ET-2 Power Heads","description":"\u003cp\u003ePart 5114 is the single-pole switch used on SEBO ET-1 and ET-2 power heads: the contact that makes and breaks the supply feeding the powered brush head.\u003c\/p\u003e\u003cp\u003eBecause the ET heads are switched independently of the machine they are plugged into, this switch is what stands between a working brush roller and a head that does nothing while everything else carries on as normal. That symptom pattern is the giveaway. The vacuum runs, suction is there, and the roller simply refuses to turn, or turns only while the switch is held at a particular point. A tired single-pole switch may also need a second press to catch, or cut the head out mid-pass when the handle flexes. It is operated at every single use, so wear here counts as a maintenance item rather than a sign of something deeper wrong with the head.\u003c\/p\u003e\u003cp\u003eSingle pole means the switch interrupts one side of the supply feeding the head, which is all that is needed to start and stop the brush motor. It is a small component doing a job that gets done thousands of times over the life of a machine, and SEBO supplies it as a service part precisely because the rest of an ET-1 or ET-2 head normally outlasts it comfortably. Replacing the switch is a far better proposition than writing off a power head that is otherwise mechanically sound.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitment:\u003c\/strong\u003e SEBO ET-1 and ET-2 power heads\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e single-pole switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction:\u003c\/strong\u003e controls the supply to the powered brush head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplace when:\u003c\/strong\u003e the switch sticks, needs repeated presses, or cuts out under use\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 5114\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eUnplug before opening the head, and keep each wire on the terminal it came off. While the head is apart it is worth turning the roller over by hand to confirm it spins freely, so that a seized roller is not mistaken for an electrical fault and a new switch fitted to cure something it was never causing. Genuine SEBO switching hardware, part 5114, packed and away in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214554882298,"sku":"5114","price":8.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/05114.jpg?v=1709348970"},{"product_id":"micro-safety-switch-w-wiring-for-et-1-and-et-2","title":"SEBO Micro Safety Switch with Wiring for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eA micro switch is what tells an ET power head it is safe to run. Part 880 is that switch for the SEBO ET-1 and ET-2, supplied complete with its wiring so nothing has to be spliced onto an existing loom or crimped by hand.\u003c\/p\u003e \u003cp\u003eWhen the switch or its leads give up, the head reads the interlock as open and simply refuses to turn. That is easy to mistake for a failed brush motor or a broken wand connection, and it is the reason ET heads get replaced when a small component was the whole problem. The pattern is recognisable: the canister motor runs normally, the head stays silent, and there is no motor sound at all from the nozzle rather than a straining one. Fitting the correct original switch, wiring included, restores the interlock and normal running in one part instead of a chain of guesses.\u003c\/p\u003e \u003cul\u003e \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 880\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eMachines:\u003c\/strong\u003e SEBO ET-1 and ET-2 power heads\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e micro safety interlock switch, wiring supplied\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003ePoints to it:\u003c\/strong\u003e the head will not turn, the interlock is not making, the brush roll is dead with no motor sound\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eInstall:\u003c\/strong\u003e move the leads across one at a time so the order cannot be lost\u003c\/li\u003e \u003cli\u003e\n\u003cstrong\u003eRelated:\u003c\/strong\u003e part 881, the on\/off switch harness for the same heads\u003c\/li\u003e \u003c\/ul\u003e \u003cp\u003eParts 880 and 881 solve different complaints on the same heads, and it is worth being clear which one you have. A head that is completely dead from the moment it is connected points at the interlock switch supplied here. A head that starts and then cuts in and out as the wand is moved points instead at the on\/off harness, part 881.\u003c\/p\u003e\u003cp\u003eDisconnect the machine from the outlet before opening the head, and inspect the wand contacts while you are in there, since a dirty contact set produces symptoms close enough to be confused with this fault. A SEBO ET-1 safety switch, an ET-2 interlock switch with wiring or a genuine SEBO power head micro switch is part 880. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214555177210,"sku":"880","price":20.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0880.jpg?v=1709348451"},{"product_id":"switch-complete-for-et-1-and-et-2-with-lever-and-leaf-spring-2958er-05114-and-wire-0881-to-pcb","title":"SEBO Complete Switch Assembly for Switched ET-1 and ET-2 Power Heads","description":"\u003cp\u003eComplete switch assemblies save the guesswork when a switched power head goes dead. Part 2959ER arrives built up with the 2958ER lever and its leaf spring, the single pole switch 05114, and the 0881 wire that runs back to the PCB, so nothing has to be salvaged off the old unit at the bench.\u003c\/p\u003e\u003cp\u003eSEBO shows the assembly at position 141 on the ET-1\/ET-2 power head diagram, covering items 131 to 133, and at position 138 on the DART where it takes in items 139 to 141. Order it when the brush roll runs only while the button is held down, when the switch has stopped latching, or when the wire has broken away at the board end. Buying the group complete also sidesteps the awkward part of the job, which is transferring a wire onto a new switch body in a confined housing. The lens that covers the button is a separate moulding, part 2957, and is worth replacing at the same time if it has yellowed or cracked.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2959ER, complete assembly\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupplied with:\u003c\/strong\u003e the 2958ER lever with leaf spring, switch 05114, and the 0881 wire to the PCB\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads built with the on\/off switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram positions:\u003c\/strong\u003e 141 on the power head sheet, taking in 131 to 133; 138 on the DART, taking in 139 to 141\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2957 button lens, 2684ER printed circuit board\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eAnyone searching for a SEBO ET-2 power head switch replacement wants the whole group rather than the individual contacts, and this is that part. Genuine SEBO assembly from an authorized dealer, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214555275514,"sku":"2959ER","price":20.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2959ER.jpg?v=1785156150"},{"product_id":"swivel-neck-support-r-h-for-et-1-and-et-2","title":"SEBO Right-Hand Swivel Neck Support for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eBraces on either flank hold the neck pivot square to the floor head, and 2311 is the right-hand one for ET-1 plus ET-2 power heads. It shows up as position 123 in the ET 1 \/ ET 2 power head, DART and FELIX diagrams, described in each as the right swivel neck support.\u003c\/p\u003e\u003cp\u003ePlay at the pivot rarely begins in the pivot itself. More often a brace has fractured around its mounting boss, letting the joint shift under load so the head wanders off line and the whole assembly feels vague in the hand. Because the crack usually runs where the plastic is thinnest and the part stays in place after it splits, the damage is easy to miss on a quick look. The reliable test is to take the brace off and flex it between finger and thumb; a sound one resists, a failed one hinges. Symptoms worth taking seriously are a rattle from the joint, steering that has lost its precision, and a head that no longer tracks straight when pushed at speed.\u003c\/p\u003e\u003cp\u003eThe pair share identical duty and identical hours, so the left-hand brace, part 2312, is worth checking the same way while the head is already open. Fitment runs across the SEBO FELIX Premium, FELIX 2 Premium, DART and C3.1 uprights and the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium canisters, on ET-1 and ET-2 heads alike, switched or unswitched. Nothing about the wiring layout of the head changes the choice, since the support is a purely structural moulding with no electrical role.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 as well as ET-2 power heads, switched or unswitched\u003c\/li\u003e\n\u003cli\u003ePart number: 2311\u003c\/li\u003e\n\u003cli\u003eRight-hand side\u003c\/li\u003e\n\u003cli\u003eDiagram position: 123 in the ET 1 \/ ET 2, DART and FELIX parts lists\u003c\/li\u003e\n\u003cli\u003eSold individually; the left-hand support is part 2312\u003c\/li\u003e\n\u003cli\u003eHolds the neck pivot square to the head under push and pull loads\u003c\/li\u003e\n\u003cli\u003eRelated neck assemblies: 2307GS gray black, 2307HG light gray\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eShips in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214555767034,"sku":"2311","price":14.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/c569b178571c6e421bc7f97fb5a9267f.jpg?v=1786668840"},{"product_id":"swivel-neck-support-l-h-for-et-1-and-et-2","title":"SEBO Left-Hand Swivel Neck Support for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eMirror image of part 2311, this brace carries the opposite flank of the neck pivot on ET-1 plus ET-2 floor nozzles. Part 2312 appears at position 124 in the ET 1 \/ ET 2 power head, DART and FELIX diagrams as the left swivel neck support.\u003c\/p\u003e\u003cp\u003eThese braces are what stop the pivot twisting out of alignment as the handle is pushed and pulled. A hairline fracture is easy to miss and produces a maddeningly vague fault: loose steering, a rattle from the joint, and nothing visibly wrong until the brace is off the machine and flexed between finger and thumb. What makes it worth pursuing is that the same looseness gets blamed on the neck assembly, which is a far larger job, so ruling the braces out first saves opening the head twice. A support that has failed at its mounting boss will often still sit in position under its screw, which is exactly why a visual check alone is not enough.\u003c\/p\u003e\u003cp\u003eDoing both flanks at once is the repair that actually holds, since the two see identical hours and the surviving brace is usually not far behind. The right-hand support is part 2311, and the neck itself is 2307GS in gray black or 2307HG in light gray for ET-1 heads. Fitment covers the SEBO FELIX Premium, FELIX 2 Premium, DART and C3.1 uprights along with the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium canisters, on ET-1 and ET-2 heads alike. Switch layout makes no difference to the order, because the brace is structural and carries nothing electrical.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 as well as ET-2 power heads, switched or unswitched\u003c\/li\u003e\n\u003cli\u003ePart number: 2312\u003c\/li\u003e\n\u003cli\u003eLeft-hand side\u003c\/li\u003e\n\u003cli\u003eDiagram position: 124 in the ET 1 \/ ET 2, DART and FELIX parts lists\u003c\/li\u003e\n\u003cli\u003eSold individually; the right-hand support is part 2311\u003c\/li\u003e\n\u003cli\u003eKeeps the neck pivot aligned under push and pull loads\u003c\/li\u003e\n\u003cli\u003eRelated neck assemblies: 2307GS gray black, 2307HG light gray\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eShips in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214555832570,"sku":"2312","price":12.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/323c135cfb4faec86002631df98a4910.jpg?v=1786668843"},{"product_id":"swivel-neck-bearing-for-et-1-et-2-and-disco","title":"SEBO Swivel Neck Bearing for FELIX, DART, ET-1, ET-2 and DISCO","description":"\u003cp\u003eTurning a SEBO upright into a corner puts every bit of that load through the swivel neck bearing. Part 2954 is the factory bearing for the joint, letting the head rotate against its housing without the stiffness or side-to-side play that makes an upright tiring to push around furniture.\u003c\/p\u003e\u003cp\u003eIt appears at position 122 on the ET-1\/ET-2 power head diagram, at 122 on the DART sheet and at 122 for the FELIX, sitting just before the right and left swivel neck supports at 123 and 124. Roughness felt through the handle, a low grinding note as you turn, or a head that flops when the machine is stood upright are the classic signs the bearing has had enough. It rarely wears alone: the six-piece metal segment set 2950ER at position 116 and the swivel neck slide at 119 share the same steering loads, and the support axle 2928 at 126 runs in the same assembly, so inspect all of them while the neck is apart.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 2954\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, switched and unswitched, plus the DISCO floor polisher\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso listed for:\u003c\/strong\u003e FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 PREMIUM, AIRBELT E3 Premium and AIRBELT K3 PREMIUM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiagram position:\u003c\/strong\u003e 122 on the power head, DART and FELIX sheets\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJob:\u003c\/strong\u003e carries the rotational load between head and neck\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated part numbers:\u003c\/strong\u003e 2950ER metal segment set, 2945GS and 2945HG slides, 2928 support axle, 2311 and 2312 neck supports\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA full SEBO swivel neck rebuild comes down to a handful of parts, and this bearing is the one that decides whether the finished joint turns sweetly or merely turns. Order it with the segment set if the neck has covered years of carpet, since the two wear together and the labour is the same either way. Genuine SEBO bearing from an authorized dealer, shipping in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214557536506,"sku":"2954","price":6.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/5330c63b8f82d3f0e287d4f04a6f457a.jpg?v=1786668943"},{"product_id":"swivel-neck-complete-for-et-1-and-et-2-gray-black","title":"SEBO Complete Swivel Neck for ET-1 and ET-2 Power Heads — Gray Black","description":"\u003cp\u003eWhere the wand meets the floor head, one moulded joint has to pivot, lie down flat and pass both air and current at the same time. That joint is the swivel neck, and 2307GS is the complete gray black assembly for ET-1 as well as ET-2 power heads, shown at position 113 in the ET 1 \/ ET 2 power head diagram and again at position 113 in the FELIX diagram.\u003c\/p\u003e\u003cp\u003eFailures here read as a head that will not recline properly, a nozzle that resists turning, or brush drive that comes and goes as the joint articulates. That last one is the clearest signal, because the conductors running through the neck flex at the same point on every stroke and eventually fatigue where the moulding bends hardest. Mechanical wear arrives alongside it: the pivot loosens, the head starts to feel vague on corners, and in bad cases the neck will no longer hold the head at the lowest reclined position for under-furniture work.\u003c\/p\u003e\u003cp\u003eBecause the part ships as a full assembly there are no clips or bushings to salvage from the damaged one. Note how the internal leads are dressed before removal so the replacement goes back on the same routing, and check the neck supports on either flank while everything is apart, since a cracked brace produces very similar symptoms. Those are parts 2311 on the right and 2312 on the left, and both are quick to test by flexing them once they are off the machine. Light gray ET-1 heads take neck 2307HG instead of this one.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, FELIX 2 Premium, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 as well as ET-2 power heads, switched or unswitched\u003c\/li\u003e\n\u003cli\u003ePart number: 2307GS\u003c\/li\u003e\n\u003cli\u003eColour: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 113 in the ET 1 \/ ET 2 and FELIX parts lists\u003c\/li\u003e\n\u003cli\u003eSupplied as one complete assembly, with pivot and wiring path renewed together\u003c\/li\u003e\n\u003cli\u003eCarries airflow, the brush drive feed and the steering load of the machine\u003c\/li\u003e\n\u003cli\u003eRelated numbers: 2307HG light gray neck, 2311 and 2312 neck supports\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eShips in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214557831418,"sku":"2307GS","price":44.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/2307GS.jpg?v=1785146191"},{"product_id":"pile-adjustment-assembly-for-et-1-and-et-2-gray-black","title":"SEBO Pile Adjustment Assembly for ET-1 and ET-2 Power Heads — Gray Black","description":"\u003cp\u003eHeight selection on an ET-1 or ET-2 head runs through a single mechanism, and 2316GS is that mechanism complete in gray black. It governs how far the brush drops toward the floor, so the bristles reach into the pile on carpet without the nozzle pinning itself down on deep pile or riding too high to make contact on a short weave.\u003c\/p\u003e\u003cp\u003eBecause it is supplied as an assembly rather than as loose linkage pieces, it goes in as a unit and there is nothing to align on the bench first. SEBO lists it at position 107 in the ET 1 \/ ET 2, DART and FELIX diagrams. Order one when a setting refuses to hold, when the selector moves without changing anything, or when the nozzle stays at one height whatever the control says. A related complaint is a head that has become hard to push on one particular floor covering, which usually means the mechanism has dropped to its lowest position and stuck there.\u003c\/p\u003e\u003cp\u003eBefore ordering, take the head off the wand and check that nothing is simply jammed with debris, since packed hair around the linkage mimics a failed mechanism. If the selector still moves freely but the brush height never changes, the linkage itself has given up. Fitment covers the SEBO FELIX Premium, FELIX 2 Premium, DART and C3.1 uprights along with the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium canisters, on ET-1 and ET-2 heads alike. Light gray heads take the matching assembly 2316HG.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 as well as ET-2 power heads, switched or unswitched\u003c\/li\u003e\n\u003cli\u003ePart number: 2316GS\u003c\/li\u003e\n\u003cli\u003ePile height adjustment assembly, supplied complete\u003c\/li\u003e\n\u003cli\u003eColour: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 107 in the ET 1 \/ ET 2, DART and FELIX parts lists\u003c\/li\u003e\n\u003cli\u003eReplaces the whole linkage rather than individual pieces\u003c\/li\u003e\n\u003cli\u003eRelated number: 2316HG in light gray\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO part. Ships in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214559895802,"sku":"2316GS","price":18.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/cd8df65c3d5cac6691c18798e8bba935.jpg?v=1786668858"},{"product_id":"wheel-complete-for-et-1-and-et-2-gray-black","title":"SEBO Power Head Wheel Assembly for ET-1 and ET-2 — Gray Black","description":"\u003cp\u003ePush a floor head across bare boards and a flat-spotted wheel announces itself straight away. Item 2306GS is the complete gray black wheel fitted to ET-1 and ET-2 power heads, supplied already assembled so it goes straight onto the machine with nothing to build up on the bench first.\u003c\/p\u003e\u003cp\u003eSEBO carries it at position 111 across three sheets, the ET 1 \/ ET 2 power head diagram, the DART diagram and the FELIX diagram. Wheels fail in three ordinary ways. Hair and thread wind around the axle until the wheel turns stiffly or not at all, the rim chips on a threshold strip or a stair nosing, and plain abrasion flattens one part of the tread so the head thumps once per revolution. A seized wheel is the one that does real harm, because from that point the head skids rather than rolls and can leave grey marks along hard flooring.\u003c\/p\u003e\u003cp\u003eFitment here is unusually broad. The same wheel serves the SEBO FELIX Premium, FELIX 2 Premium, DART and C3.1 uprights along with the AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium canisters, and it suits ET-1 as well as ET-2 heads whether or not they carry an on\/off rocker. Confirm the new wheel spins freely once seated, and clear any wound thread from the axle boss while access is easy, since a clean boss is what keeps the next wheel turning. Working on both sides at the same visit is the sensible approach when one has already flat-spotted, because the other has covered the same distance. Light gray heads take the matching wheel 2306HG instead.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits the SEBO FELIX Premium, FELIX 2 Premium, DART, C3.1, AIRBELT D4 Premium, AIRBELT E3 Premium and AIRBELT K3 Premium\u003c\/li\u003e\n\u003cli\u003eSuits ET-1 as well as ET-2 power heads, switched or unswitched\u003c\/li\u003e\n\u003cli\u003ePart number: 2306GS\u003c\/li\u003e\n\u003cli\u003eColour: gray black\u003c\/li\u003e\n\u003cli\u003eDiagram position: 111 in the ET 1 \/ ET 2, DART and FELIX parts lists\u003c\/li\u003e\n\u003cli\u003eSupplied as one complete wheel assembly, nothing to press together\u003c\/li\u003e\n\u003cli\u003eRelated number: 2306HG in light gray\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eShips in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214560256250,"sku":"2306GS","price":16.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/25fe82fd892814d477c78c578b62496c.jpg?v=1786668826"},{"product_id":"et-2-power-head-with-on-off-switch-for-d4-red","title":"SEBO ET-2 Power Head with On\/Off Switch for C3.1 — Red","description":"\u003cp\u003eCarpet is where suction alone runs out of ideas, and the ET-2 is the wider of the two driven floor heads SEBO builds to make up the difference. This is the red one, part 9250AM, with the control mounted on the head itself.\u003c\/p\u003e\u003cp\u003eA motor inside the housing turns the brush shaft, so the roller keeps combing the pile at its own steady rate instead of depending on how much air is passing through it. The size difference between the families is easy to check against a parts list: an ET-2 takes SEBO's 15-inch brush roller, listed as 2838AM with 2838GE as the soft-bristle alternative, where the smaller ET-1 takes a 12-inch roller. The rocker on top is the second thing to check, because it decides which sibling number you need. 9251AM is the same ET-2 body in black with no control on the head, meant for installations that start and stop the brush somewhere upstream; 9259AM is white with a switch and 9958AM is black with a switch.\u003c\/p\u003e\u003cp\u003ePeople usually reach for a whole head rather than internals after a fall has cracked the housing, when the drive has stopped turning the roller, or when a second head is wanted so a spare hose is ready to go. If the head being replaced has a rocker on it, this is the like-for-like part in red.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO C3.1, and systems specified for the switched ET-2 head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 9250AM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eControl:\u003c\/strong\u003e on\/off rocker on the head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e red\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrush roller:\u003c\/strong\u003e 15-inch 2838AM, soft-bristle 2838GE\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSame head, other builds:\u003c\/strong\u003e 9259AM white, 9958AM black, 9251AM black without a switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUseful alongside:\u003c\/strong\u003e 8366WS brush roller cleaning tool\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eSupplied new and genuine by an authorized SEBO dealer. Ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214562287866,"sku":"9250AM","price":389.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/0b3164c934b5760e461f45e97040fe39.jpg?v=1786667398"},{"product_id":"et-2-power-head-with-on-off-switch-white","title":"SEBO ET-2 Power Head with On\/Off Switch for FELIX and C3.1 — White","description":"\u003cp\u003ePairing a white machine with a matching floor head is the usual reason this number gets ordered. 9259AM is the ET-2, the wider of SEBO's two driven heads, finished in white and fitted with its own on\/off control. It is listed for the FELIX Premium and FELIX 2 Premium uprights and for the C3.1.\u003c\/p\u003e\u003cp\u003eInside the housing a dedicated motor spins the brush shaft, so the roller keeps agitating carpet regardless of how much suction is reaching the hose — the difference between lifting grit out of pile and sliding it along the top of it. Being able to stop the brush at the head is what makes the switched version worth having on rugs and smooth flooring, where a live roller is a nuisance. The head's size shows up in its consumables: an ET-2 takes the 15-inch brush roller 2838AM, or 2838GE in soft bristle, where an ET-1 takes a 12-inch roller.\u003c\/p\u003e\u003cp\u003eHair and thread wind themselves around any driven roller in a house with long-haired occupants or pets, and 8366WS is the tool for cutting it free before the load reaches the bearings. Doing that occasionally is usually the difference between replacing a roller and replacing a head.\u003c\/p\u003e\u003cp\u003eCheck the old head before ordering. If it has no rocker, the unswitched ET-2 is 9251AM. If it is the smaller family, the white ET-1 with a switch is 9258AM. The same white ET-2 is also built in red as 9250AM and black as 9958AM for owners matching a differently finished machine.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO FELIX Premium, FELIX 2 Premium and C3.1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 9259AM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eControl:\u003c\/strong\u003e on\/off rocker on the head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e white\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrush roller:\u003c\/strong\u003e 2838AM 15-inch, 2838GE soft bristle\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlternatives:\u003c\/strong\u003e 9251AM unswitched, 9250AM red, 9958AM black, 9258AM white ET-1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaintenance:\u003c\/strong\u003e 8366WS brush roller cleaning tool\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO stock from an authorized dealer. Ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214562353402,"sku":"9259AM","price":389.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/52d6745c20872ca945540e733abb760d.jpg?v=1786667429"},{"product_id":"et-2-power-head-with-on-off-switch-black","title":"SEBO ET-2 Power Head with On\/Off Switch — Black","description":"\u003cp\u003eOrdering by colour alone gets people into trouble with these heads, so start with the family. 9958AM is an ET-2, the wider of SEBO's two driven floor heads, finished in black and built with an on\/off control on the head itself.\u003c\/p\u003e\u003cp\u003eThe brush roll is turned by a motor carried inside the housing, which is what separates a power head from a plain suction floor tool once there is carpet under it. A rocker on the head means the roller can be stopped without touching the machine, useful the moment you cross onto a hard floor or a rug that would otherwise be dragged along. Consumables tell the two families apart at a glance: the ET-2 takes the 15-inch brush roller 2838AM, or 2838GE in soft bristle, where an ET-1 takes a 12-inch roller, so a parts receipt for the old machine is often the fastest way to confirm which you have.\u003c\/p\u003e\u003cp\u003eThe same ET-2 body is produced in red as 9250AM and in white as 9259AM, and 9251AM is the black one with no control at all, so check what the old head carried before ordering. Central vacuum installations fitting a head to a new hose usually want the 2780AM adapter and the 6272CA telescopic wand alongside it.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO systems specified for the switched ET-2 head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 9958AM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eControl:\u003c\/strong\u003e on\/off rocker on the head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrush roller:\u003c\/strong\u003e 2838AM 15-inch, 2838GE soft bristle\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOther builds:\u003c\/strong\u003e 9250AM red, 9259AM white, 9251AM black without a switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated:\u003c\/strong\u003e 2780AM wand adapter, 6272CA telescopic wand\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO head from an authorized dealer, supplied complete rather than as internals to transplant into an old shell. Ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214562418938,"sku":"9958AM","price":389.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/dec2db696845b6de4918318c2e7ed472.jpg?v=1786667491"},{"product_id":"et-2-power-head-without-on-off-switch-for-central-vacuums-black","title":"SEBO ET-2 Power Head without On\/Off Switch for Central Vacuum Systems — Black","description":"\u003cp\u003eNo control on the housing at all: 9251AM is the ET-2 floor head in black, built for central vacuum installations where the brush is switched at the handle or back at the power unit rather than under your foot.\u003c\/p\u003e\u003cp\u003eEverything else follows the ET-2 pattern. A motor carried inside the head turns the brush shaft, which is what keeps the roller working pile at a constant rate rather than leaving the job to airflow. It is the wider of SEBO's two driven heads, and the parts list confirms it: the roller specified for an ET-2 is the 15-inch 2838AM, or 2838GE where soft bristles are wanted for finer floor coverings, against a 12-inch roller in the smaller ET-1. Choosing correctly between switched and unswitched matters more than it sounds, since a head with its own rocker fitted to a system that already controls the brush elsewhere leaves two places to remember and one of them usually gets forgotten.\u003c\/p\u003e\u003cp\u003eOrder this one when the old head is cracked, when its drive has failed, or when a second head keeps a large installation running while the first is serviced. The switched equivalents are 9250AM in red, 9259AM in white and 9958AM in black. Central vacuum owners fitting a head to a new hose often need the 2780AM wand adapter with its 34-inch cord, and 6272CA is the telescopic wand listed for these systems.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e SEBO central vacuum systems specified for the ET-2 head without a switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e 9251AM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eControl:\u003c\/strong\u003e none on the head, switched upstream\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColour:\u003c\/strong\u003e black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrush roller:\u003c\/strong\u003e 2838AM 15-inch, or 2838GE soft bristle\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitched versions:\u003c\/strong\u003e 9250AM, 9259AM, 9958AM\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated:\u003c\/strong\u003e 2780AM wand adapter, 6272CA telescopic wand, 6272PI wand with a plastic tip\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaintenance:\u003c\/strong\u003e 8366WS brush roller cleaning tool\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eGenuine SEBO head from an authorized dealer. Ships in 2–5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214562451706,"sku":"9251AM","price":379.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/16fef3b9c0679af9919acd644cd26967.jpg?v=1786667408"},{"product_id":"central-vacuum-telescopic-wand-for-et-1-and-et-2","title":"SEBO Central Vacuum Telescopic Wand for ET-1 and ET-2 Power Heads","description":"\u003cp\u003eWorking height on a central vacuum is set by the wand rather than the hose, and part 6272CA is the SEBO telescopic tube built to sit between the hose handle and an ET power head. It extends to wherever your back is comfortable, locks there, and collapses again for the closet.\u003c\/p\u003e\u003cp\u003eIt fits the SEBO ET-1 and ET-2 power heads in both the switched and the unswitched builds. A wand carries the entire airstream from the head up to the hose, so its condition matters more than its appearance suggests. A dented tube leaks air along its length, a tired locking collar creeps shorter under the weight of the head, and a scored joint bleeds off suction quietly for as long as the machine runs.\u003c\/p\u003e\u003cp\u003eWhat owners describe is weak pickup at the floor with a motor that sounds perfectly healthy, and the wand is one of the first things worth ruling out. Fitting a sound tube puts the seal back across the full run from head to hose, and the head starts lifting what it should again.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart:\u003c\/strong\u003e 6272CA telescopic wand for central vacuum systems\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits:\u003c\/strong\u003e ET-1 and ET-2 power heads, with or without switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength:\u003c\/strong\u003e adjusts and locks anywhere across its telescopic range\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRelated:\u003c\/strong\u003e 6272PI is the same wand supplied with a plastic tip\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlso useful:\u003c\/strong\u003e 2780AM, the adapter with 34 in. cord for running an ET head on central vacuum tubing\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplace when:\u003c\/strong\u003e the tube is dented, the collar slips under load, or the joint leaks air\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eA wand is also the part most often damaged by something other than use. Wheeled over, stood on or dropped down a stairwell, it bends where the tube is thinnest and never seals properly again afterwards. Ordering the SEBO original matters here because the electrical path and the way the tube enters the ET head are both part of the design, not simply a question of diameter.\u003c\/p\u003e\u003cp\u003eGenuine SEBO replacement, out the door in 2-5 business days.\u003c\/p\u003e","brand":"SEBO","offers":[{"title":"Default Title","offer_id":45214562484474,"sku":"6272CA","price":79.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0684\/3934\/3354\/files\/6272CA_070421b2-e0ea-4d7e-b6ad-6a2045b3fccf.jpg?v=1785149202"}],"url":"https:\/\/evacuumsandmore.com\/collections\/sebo-et-2.oembed?page=3","provider":"Vacuums and More","version":"1.0","type":"link"}